Polymer Structure and Property III

The adhesion characteristics and surface energies of two series of polyamidoimides (PAI) with different molecular weights, monomer unit structures, hinge groups in the main chain of the macromolecules, and thermal prehistory were determined via delamination at 180° and test fluids contact angles. We found that PAI are high-energy polymers, the surface energy of which varies in the range from 32 to 45 mJ/m². In contrast to flexible-chain polymers, the exponent in the McLeod equation is two, which is due to the flat parallel orientation of the macromolecular chains in the surface layers. The main contribution to the change in surface characteristics of these polymers is the change in the packing density of PAI macromolecules, which is reflected mainly in the change in the polymers’ dispersion component. We found that the adhesion properties of PAI with respect to high- and low-energy substrates are determined mainly by the macromolecules packing density in the surface layers with their conformation state unchanged. Full article

The influence of reactive processing, non reactive and reactive copolymers on immiscible polypropylene (PP)–polystyrene (PS) blends with varying PS concentrations (10 wt.% and 25 wt.%) was evaluated by mechanical (tensile and tensile impact), rheological (melt flow rate, extensional and dynamic rheology) and morphological (scanning electron microscopy) analysis. As an extended framework of the study, the creation of a link to industrial applicable processing conditions as well as an economically efficient use of compatibilzing agent were considered. For radical processed blends, a high improvement in melt strength was observed while non reactive copolymers exhibited a pronounced increase in toughness and ductility correlated with overall best phase homogeneity. Conversely, the influence of the reactive copolymer was quite different for the varied PS concentrations not allowing the assumption of a specific trend for resulting blend properties, but nevertheless in the case of a lower PS concentration the tensile impact strength exceeded the value of virgin PP. Since PS and PP are widely used, the findings of this work could not only be relevant for the generation of more versatile blends compared to virgin components but also for recycling purposes, allowing the enhancement of specific properties facilitating the production of more valuable secondary materials. Full article

This paper investigates the photo-initiated cationic polymerization of diglycidyl ether of bisphenol A (DGEBA) modified with bisphenol A (BPA)/polyethylene glycol (PEG) hyperbranched epoxy resin. The relationship between curing behavior, rheological, and thermal properties of the modified DGEBA is investigated using photo-differential scanning calorimetry (DSC) and photo-rheometer techniques. It is seen that the addition of the hyperbranched epoxy resin can increase UV conversion (α_UV) and reduce gelation time (t_gel). After photo-initiation polymerization (dark reaction) occurred, a second exothermic peak in the DSC thermogram takes place: namely, the occurrence of curing reaction owing to the activated monomer (AM) mechanism. Consequently, the glass transition temperature decreased, and at the same time, UV intensity increased which was due to the molecular weight between crosslinking points (M_c). Furthermore, the radius of gyration (R_g) of the network segment is determined via small-angle X-ray scattering (SAXS). It is noted that the higher the M_c, the larger the radius of gyration proves to be, resulting in low glass transition temperature. Full article

Poly(butylene terephthalate-co-tetramethylene ether glycol) (PBT-co-PTMEG) copolymers with PTMEG ranging from 0 to 40 wt% were synthesized through melt polymerization. The structure and composition were supported by Fourier-transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance spectroscopy (¹H NMR). All samples had excellent thermal stability at a T_d−5% around 370 °C. Crystallization temperature (T_c) and enthalpy of crystallization (ΔH_c) were detected by differential scanning calorimetry (DSC), revealing a decrement from 182.3 to 135.1 °C and 47.0 to 22.1 J g⁻¹, respectively, with the increase in PTMEG concentration from 0 to 40 wt%. Moreover, nonisothermal crystallization was carried out to explore the crystallization behavior of copolymers; the crystallization rate of PBT reduced gradually when PTMEG content increased. Hence, a decrement in the spherulite growth rate was detected in polarizing light microscope (PLM) observation, observing that the PTMEG could enhance the hindrance in the molecular chain to lower the crystallinity of PBT-co-PTMEG copolyester. Moreover, thermal properties and the crystallization rate of PBT-co-PTMEG copolymers can be amended via the regulation of PTMEG contents. Full article

Star-shaped polymers are very attractive because of their potential application ability in various technological areas due to their unique molecular topology. Thus, information on the molecular structure and chain characteristics of star polymers is essential for gaining insights into their properties and finding better applications. In this study, we report molecular structure details and chain characteristics of 17-armed polystyrenes in various molecular weights: 17-Arm(2k)-PS, 17-Arm(6k)-PS, 17-Arm(10k)-PS, and 17-Arm(20k)-PS. Quantitative X-ray scattering analysis using synchrotron radiation sources was conducted for this series of star polymers in two different solvents (cyclohexane and tetrahydrofuran), providing a comprehensive set of three-dimensional structure parameters, including radial density profiles and chain characteristics. Some of the structural parameters were crosschecked by qualitative scattering analysis and dynamic light scattering. They all were found to have ellipsoidal shapes consisting of a core and a fuzzy shell; such ellipse nature is originated from the dendritic core. In particular, the fraction of the fuzzy shell part enabling to store desired chemicals or agents was confirmed to be exceptionally high in cyclohexane, ranging from 74 to 81%; higher-molecular-weight star polymer gives a larger fraction of the fuzzy shell. The largest fraction (81%) of the fuzzy shell was significantly reduced to 52% in tetrahydrofuran; in contrast, the lowest fraction (19%) of core was increased to 48%. These selective shell contraction and core expansion can be useful as a key mechanism in various applications. Overall, the 17-armed polystyrenes of this study are suitable for applications in various technological fields including smart deliveries of drugs, genes, biomedical imaging agents, and other desired chemicals. Full article

Thermoplastic vulcanizate (TPV) has excellent elastomeric properties and can be reprocessed multiple times. TPV is typically produced by using the dynamic vulcanization (DV) method in which rubber is crosslinked simultaneously with thermoplastics. Peroxide-crosslinked TPV can increase the compatibility between rubber and thermoplastics but loses its reprocessability due to excess crosslinking in the latter. In this work, we overcome this obstacle by using a two-step mixing method to prepare fully crosslinked elastomers of ethylene vinyl acetate copolymer (EVA) and natural rubber (NR). Each sample formulation was prepared with three different mixing methods for comparison: NR-DV, Split-DV, and All-DV. For NR-DV, NR was crosslinked prior to the addition of EVA together with the thermal stabilizer (TS). For Split-DV, a small amount of EVA and NR was crosslinked prior to the addition of EVA and TS. In the All-DV method, EVA and NR were crosslinked, and then TS was added. The appearance and processability of the samples were affected by the degree of crosslinking. NR-DV showed a non-homogeneous texture. Although the samples of the All-DV method appeared homogeneous, their mechanical and rheological properties were inferior to those of the Split-DV method. The mechanical properties of the Split-DV samples were not significantly changed after reprocessing 10 times. Therefore, Split-DV is the preferred method for TPV production. Full article