sensors-logo

Journal Browser

Journal Browser

Luminescence and Chemiluminescence Sensors

A special issue of Sensors (ISSN 1424-8220). This special issue belongs to the section "Chemical Sensors".

Deadline for manuscript submissions: closed (10 June 2018) | Viewed by 25116

Special Issue Editors


E-Mail Website
Guest Editor
University of Córdoba, Department of Analytical Chemistry, University Institute of Research in Fine Chemistry and Nanochemistry (IUIQFN), Córdoba, Spain
Interests: microfluidic sensor and biosensors development, new sensing nanomaterials (nanoparticles and liposomes); luminescence sensing; agri-food, clinical and toxicological analysis

E-Mail Website
Guest Editor
University of Córdoba, Department of Analytical Chemistry, University Institute of Research in Fine Chemistry and Nanochemistry (IUIQFN), Córdoba, Spain
Interests: biosensor development; new hybrid nanomaterials for sensing; luminescence sensors; agri-food; clinical and toxicological analysis

Special Issue Information

Dear Colleagues,

This Special Issue aims to cover the most recent achievements in luminescence and chemiluminescence sensors under the principle of integrating chemical, biochemical or mimetic, recognition elements to a physicochemical transducer in order to generate a luminescence signal, which is easily understood by the operator. Contributions covering either review or original articles on new sensing principles or the application of recently developed sensors to the clinical, pharmaceutical, toxicological, or agri-food analysis, among others, will be welcome.

The development of new sensing approaches, based on multiple luminescence (time-resolved, anti-Stokes, fluorescence resonance energy transfer (FRET), direct photoluminescence) or chemiluminescence phenomena are under continuous development. The integration of nanostructures (nanomaterials, liposomes, and scaffolds) into the (bio)sensing area is one of the most ongoing expansion. The incorporation of nanomaterials in the (bio)sensing zone offer advantageous surface-to-volumes ratios, outstanding surfaces properties, that help to improve basic analytical (bio)sensor features, such as sensitivity and selectivity. Innovations may also include essential developments in (bio)receptors, (bio)mimetics, electronics, transduction, microfluidics, lab-on-a-chip or the latest uses of remote smartphone readouts.

In order to provide our readers with the latest advances on luminescence and chemiluminescence (bio)sensor advances, we would like to invite you to consider submitting a manuscript to our upcoming Special Issue, “Luminescence and Chemiluminescence (Bio)sensors”, to be published in 2018. Under the expanded scope of the journal, this Special Issue aims to gather a collection of papers dedicated to all aspects of luminescence phenomena exploited in (bio)sensing, with emphasis on novel approaches to (bio)sensor design, integrated luminometric devices, signal transduction and recent applications. If authors are interested in contributing to this Special Issue, we would very much appreciate receiving the tentative title and an outlined abstract of the proposed article.

Dr. Juan Manuel Fernández-Romero
Dr. María Paz Aguilar-Caballos
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Sensors is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

 

  • (Bio)sensors
  • Luminescence
  • Chemiluminescence
  • Lateral-flow (bio)sensors
  • Microfluidic biosensors
  • On-Chip (bio)sensors
  • Time-resolved luminescence
  • Up-conversion nanophosphors
  • FRET
  • Molecular beacons
  • Nanomaterials
  • Nanoparticles
  • Multiplexed (bio)sensing

Published Papers (5 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

Jump to: Review

9 pages, 4157 KiB  
Article
Plasmonic-Ceria Nanoparticles as Fluorescence Intensity and Lifetime Quenching Optical Sensor
by Nader Shehata, Effat Samir and Ishac Kandas
Sensors 2018, 18(9), 2818; https://doi.org/10.3390/s18092818 - 27 Aug 2018
Cited by 7 | Viewed by 3593
Abstract
Ceria nanoparticles have been recently used as an optical fluorescent material with visible emission under ultraviolet excitation, due to the formation of trivalent cerium ions with corresponding oxygen vacancies. This paper introduces the enhancement of both fluorescence emission and lifetime through adding gold [...] Read more.
Ceria nanoparticles have been recently used as an optical fluorescent material with visible emission under ultraviolet excitation, due to the formation of trivalent cerium ions with corresponding oxygen vacancies. This paper introduces the enhancement of both fluorescence emission and lifetime through adding gold nanoparticles. The reason is due to possible coupling between the plasmonic resonance of gold nanoparticles and the fluorescence emission of ceria that has been achieved, along with enhanced formation of trivalent cerium ions. Both factors lead to higher fluorescence intensity peaks and shorter fluorescence lifetimes. As an application, gold-ceria nanoparticles have been used as an optical sensing material for lead particles in aqueous media based on fluorescence quenching. Stern-Volmer constant of in-situ gold-ceria nanoparticles is found to be 2.424 M−1, with a relative intensity change of up to 40% at 0.2 g/L. Full article
(This article belongs to the Special Issue Luminescence and Chemiluminescence Sensors)
Show Figures

Figure 1

11 pages, 2177 KiB  
Article
An Electrochemiluminescence Sensor Based on Nafion/Magnetic Fe3O4 Nanocrystals Modified Electrode for the Determination of Bisphenol A in Environmental Water Samples
by Jiye Chai, Xinru Yu, Jian Zhao, Aili Sun, Xizhi Shi and Dexiang Li
Sensors 2018, 18(8), 2537; https://doi.org/10.3390/s18082537 - 03 Aug 2018
Cited by 10 | Viewed by 3448
Abstract
The well-dispersive and superparamagnetic Fe3O4-nanocrystals (Fe3O4-NCs) which could significantly enhance the anodic electrochemiluminescence (ECL) behavior of luminol, were synthesized in this study. Compared to ZnS, ZnSe, CdS and CdTe nanoparticles, the strongest anodic ECL signals [...] Read more.
The well-dispersive and superparamagnetic Fe3O4-nanocrystals (Fe3O4-NCs) which could significantly enhance the anodic electrochemiluminescence (ECL) behavior of luminol, were synthesized in this study. Compared to ZnS, ZnSe, CdS and CdTe nanoparticles, the strongest anodic ECL signals were obtained at +1.6 V on the Fe3O4-NCs coated glassy carbon electrode. The ECL spectra revealed that the strong ECL resonance energy transfer occurred between luminol and Fe3O4-NCs. Furthermore, under the optimized ECL experimental conditions, such as the amount of Fe3O4-NCs, the concentration of luminol and the pH of supporting electrolyte, BPA exhibited a stronger distinct ECL quenching effect than its structural analogs and a highly selective and sensitive ECL sensor for the determination of bisphenol A (BPA) was developed based on the Fe3O4-NCs. A good linear relationship was found between the ECL intensity and the increased BPA concentration within 0.01–5.0 mg/L, with a correlation coefficient of 0.9972. The detection limit was 0.66 × 10−3 mg/L. Good recoveries between 96.0% and 105.0% with a relative standard deviation of less than 4.8% were obtained in real water samples. The proposed ECL sensor can be successfully employed to BPA detection in environmental aqueous samples. Full article
(This article belongs to the Special Issue Luminescence and Chemiluminescence Sensors)
Show Figures

Figure 1

10 pages, 1818 KiB  
Article
Targeting FRET-Based Reporters for cAMP and PKA Activity Using AKAP79
by Nshunge Musheshe, Miguel J. Lobo, Martina Schmidt and Manuela Zaccolo
Sensors 2018, 18(7), 2164; https://doi.org/10.3390/s18072164 - 05 Jul 2018
Cited by 11 | Viewed by 4298
Abstract
Fluorescence resonance energy transfer (FRET)-based sensors for 3′–5′cyclic adenosine monophosphate (cAMP) and protein kinase A (PKA) allow real-time imaging of cAMP levels and kinase activity in intact cells with high spatiotemporal resolution. The development of FRET-based sensors has made it possible to directly [...] Read more.
Fluorescence resonance energy transfer (FRET)-based sensors for 3′–5′cyclic adenosine monophosphate (cAMP) and protein kinase A (PKA) allow real-time imaging of cAMP levels and kinase activity in intact cells with high spatiotemporal resolution. The development of FRET-based sensors has made it possible to directly demonstrate that cAMP and PKA signals are compartmentalized. These sensors are currently widely used to dissect the organization and physiological function of local cAMP/PKA signaling events in a variety of cell systems. Fusion to targeting domains has been used to direct the sensors to a specific subcellular nanodomain and to monitor cAMP and PKA activity at specific subcellular sites. Here, we investigate the effects of using the A-kinase anchoring protein 79 (AKAP79) as a targeting domain for cAMP and PKA FRET-based reporters. As AKAP79 interacts with PKA itself, when used as a targeting domain, it can potentially impact on the amplitude and kinetics of the signals recorded locally. By using as the targeting domain wild type AKAP79 or a mutant that cannot interact with PKA, we establish that AKAP79 does not affect the amplitude and kinetics of cAMP changes or the level of PKA activity detected by the sensor. Full article
(This article belongs to the Special Issue Luminescence and Chemiluminescence Sensors)
Show Figures

Figure 1

17 pages, 1690 KiB  
Article
Polystyrene Oxygen Optodes Doped with Ir(III) and Pd(II) meso-Tetrakis(pentafluorophenyl)porphyrin Using an LED-Based High-Sensitivity Phosphorimeter
by Alexandre F. De Moraes Filho, Pedro M. Gewehr, Joaquim M. Maia and Douglas R. Jakubiak
Sensors 2018, 18(6), 1953; https://doi.org/10.3390/s18061953 - 15 Jun 2018
Cited by 4 | Viewed by 4863
Abstract
This paper presents a gaseous oxygen detection system based on time-resolved phosphorimetry (time-domain), which is used to investigate O2 optical transducers. The primary sensing elements were formed by incorporating iridium(III) and palladium(II) meso-tetrakis(pentafluorophenyl)porphyrin complexes (IrTFPP-CO-Cl and PdTFPP) in polystyrene (PS) solid [...] Read more.
This paper presents a gaseous oxygen detection system based on time-resolved phosphorimetry (time-domain), which is used to investigate O2 optical transducers. The primary sensing elements were formed by incorporating iridium(III) and palladium(II) meso-tetrakis(pentafluorophenyl)porphyrin complexes (IrTFPP-CO-Cl and PdTFPP) in polystyrene (PS) solid matrices. Probe excitation was obtained using a violet light-emitting diode (LED) (low power), and the resulting phosphorescence was detected by a high-sensitivity compact photomultiplier tube. The detection system performance and the preparation of the transducers are presented along with their optical properties, phosphorescence lifetimes, calibration curves and photostability. The developed lifetime measuring system showed a good signal-to-noise ratio, and reliable results were obtained from the optodes, even when exposed to moderate levels of O2. The new IrTFPP-CO-Cl membranes exhibited room temperature phosphorescence and moderate sensitivity: <τ0>/<τ21%> ratio of ≈6. A typically high degree of dynamic phosphorescence quenching was observed for the traditional indicator PdTFPP: <τ0>/<τ21%> ratio of ≈36. Pulsed-source time-resolved phosphorimetry combined with a high-sensitivity photodetector can offer potential advantages such as: (i) major dynamic range, (ii) extended temporal resolution (Δτ/Δ[O2]) and (iii) high operational stability. IrTFPP-CO-Cl immobilized in polystyrene is a promising alternative for O2 detection, offering adequate photostability and potentially mid-range sensitivity over Pt(II) and Pd(II) metalloporphyrins. Full article
(This article belongs to the Special Issue Luminescence and Chemiluminescence Sensors)
Show Figures

Figure 1

Review

Jump to: Research

21 pages, 1386 KiB  
Review
A Fluorescent Biosensors for Detection Vital Body Fluids’ Agents
by Witold Nawrot, Kamila Drzozga, Sylwia Baluta, Joanna Cabaj and Karol Malecha
Sensors 2018, 18(8), 2357; https://doi.org/10.3390/s18082357 - 24 Jul 2018
Cited by 58 | Viewed by 8238
Abstract
The clinical applications of sensing tools (i.e., biosensors) for the monitoring of physiologically important analytes are very common. Nowadays, the biosensors are being increasingly used to detect physiologically important analytes in real biological samples (i.e., blood, plasma, urine, and saliva). This review focuses [...] Read more.
The clinical applications of sensing tools (i.e., biosensors) for the monitoring of physiologically important analytes are very common. Nowadays, the biosensors are being increasingly used to detect physiologically important analytes in real biological samples (i.e., blood, plasma, urine, and saliva). This review focuses on biosensors that can be applied to continuous, time-resolved measurements with fluorescence. The material presents the fluorescent biosensors for the detection of neurotransmitters, hormones, and other human metabolites as glucose, lactate or uric acid. The construction of microfluidic devices based on fluorescence uses a variety of materials, fluorescent dyes, types of detectors, excitation sources, optical filters, and geometrical systems. Due to their small size, these devices can perform a full analysis. Microfluidics-based technologies have shown promising applications in several of the main laboratory techniques, including blood chemistries, immunoassays, nucleic-acid amplification tests. Of the all technologies that are used to manufacture microfluidic systems, the LTCC technique seems to be an interesting alternative. It allows easy integration of electronic and microfluidic components on a single ceramic substrate. Moreover, the LTCC material is biologically and chemically inert, and is resistant to high temperature and pressure. The combination of all these features makes the LTCC technology particularly useful for implementation of fluorescence-based detection in the ceramic microfluidic systems. Full article
(This article belongs to the Special Issue Luminescence and Chemiluminescence Sensors)
Show Figures

Figure 1

Back to TopTop