Search Results (38)

The potential for creating composite cements by incorporating fly ash is demonstrated. Analysis revealed that the fly ash examined consists of 69.66 wt. % silicon oxide, 21.34 wt. % aluminum oxide, 1.57 wt. % calcium oxide and 2.78 wt. % iron oxide. Fly ash mainly consists of quartz (SiO₂), goethite (FeO(OH)) and mullite (3Al₂O₃·2SiO₂). The properties of the cement composition containing 5 to 25 wt. % fly ash were studied. Incorporating fly ash enhances system dispersion, promotes mixture uniformity, and stimulates the pozzolanic reaction. Compositions of composite cements consisting of 90% CEM I 42.5 and 10% fly ash were developed. The cement stone based on the obtained composite cement had a compacted structure with a density of 2.160 g/cm³, which is 9.4% higher than the control sample. It is shown that when composite cement containing 10% fly ash interacts with water, hydration reactions of cement minerals (C₃S, C₂S, C₃A and C₄AF) begin first. This is accompanied by the formation of hydrate neoplasms, such as calcium hydroxide (Ca(OH)₂) and calcium hydrosilicates (C-S-H). Fly ash particles containing amorphous silica progressively participate in a pozzolanic reaction with Ca(OH)₂, leading to the formation of additional calcium hydrosilicates phases. This process enhances structural densification and reduces the porosity of the cement matrix. After 28 days of curing, the compressive strength of the resulting composite cements ranged from 42.1 to 54.2 MPa, aligning with the strength classes 32.5 and 42.5 as specified by GOST 31108-2020. Full article

Groundwater is a strategically important source of drinking water supply in the arid and rural regions of Kazakhstan. The objective of this study is to assess the quality of groundwater at 11 water intakes located in the Kordai, Shu, and Merke Districts of the Shu transboundary basin in the Zhambyl Region. A comprehensive assessment of physicochemical parameters was performed, including concentrations of nitrates, sulfates, chlorides, iron, manganese, and other constituents, with subsequent comparison against regulatory limits defined by Order No. 26 of the Ministry of Health of the Republic of Kazakhstan (dated 20 February 2023), GOST standards, and ST RK ISO standards. The findings revealed that a number of water intakes exceeded the maximum allowable concentrations for specific indicators, especially in areas subject to significant anthropogenic pressure. The most vulnerable sources were identified near settlements characterized by intensive agricultural practices and inadequate wastewater treatment systems. Spatial comparison of the results enabled the identification of potentially contaminated areas as well as aquifer zones suitable for drinking water supply. The study emphasizes the importance of regular groundwater monitoring and spatial analysis techniques (GIS) to enhance the reliability and comprehensiveness of water quality assessments. The data obtained in this study can serve as a basis for informed decision-making in the area of water resource protection and contribute to the achievement of United Nations Sustainable Development Goal 6 (SDG 6)—to ensure availability and sustainable management of water and sanitation for all. Full article

The microstructural evolution and mechanical properties of WWER 440 steam generator steel GOST 22K after long-term operation were thoroughly examined in this study. The samples were taken directly from a steam generator using the small punch test method. The uniqueness of these samples lies in the fact that they were real operating materials used in a nuclear power plant with different years of operation. The microstructure was characterized using optical microscopy and transmission electron microscopy supplemented by selective electron diffraction and semi-quantitative chemical microanalysis. It was found that with the prolongation of the operation time of the steam generator, the density of carbides increased slightly, which was reflected in a decrease in the mean distance between particles, but these differences were very small, which indicates the microstructural stability of GOST 22K steel. The stability of this steel was also confirmed by measuring its mechanical properties, which changed only minimally depending on the years of operation. The tensile strength values were in the range of 508 to 579 MPa. In the case of the ductile-to-brittle transition temperature (DBTT), a slight increase was found after 6 years of operation. The DBTT did not change significantly with subsequent operation. Full article

Coal combustion generates significant volumes of ash, a technogenic by-product that poses a serious threat to regional environmental sustainability (environmental chemical contamination and air pollution). This study aims to assess the feasibility of utilizing this type of ash as a raw material component in the fabrication of refractory bricks and to investigate the fundamental properties of the resulting experimental products. Ash was incorporated into the batch composition at concentrations ranging from 10% to 40% by weight, blended with clay and water, then shaped through pressing and subjected to firing at 1000 °C and 1100 °C in an air atmosphere for 2 h. After complete cooling, the samples were subjected to compressive strength testing. Samples containing 40 wt% coal ash exhibited insufficient compressive strength and were therefore excluded from subsequent investigations. For the remaining samples, apparent density, open porosity and slag resistance were determined. The microstructural characterization was performed, and the phase composition of the samples was analyzed. The results revealed that the phase composition of the experimental samples differs significantly from that of the reference sample (ShA-grade chamotte brick in accordance with GOST 390-96, currently used as lining in metallurgical furnaces across the country), exhibiting a higher mullite content and the absence of muscovite. A small amount of kaolinite was detected in the experimental samples even after a 2-h firing process. This observation may be attributed to the effect of kaolinite crystallinity on the transformation process from kaolinite to metakaolinite. The mechanical strength of the experimental samples meets the relevant standards, while slag resistance demonstrated an improvement of approximately 15%. Open porosity was found to decrease in the experimental samples. In addition, a change in the pore size distribution was observed. Notably, the proportion of pores larger than 10,000 nm was significantly reduced. These findings confirm the feasibility of incorporating coal ash as a viable raw material component in the formulation of refractory materials. Full article

The effects of leaf clumping on leaf area index (LAI, m²·m⁻²) retrieval have been proved by several studies. For dense and highly clumped Moso bamboo canopies, LAI is usually retrieved using the SAIL-series models that do not account for leaf clumping, although these retrievals are subsequently successfully validated by indirect ground-based methods that do account for leaf clumping. In order to explore these two seemingly contradictory results, LAIs of 21 Moso bamboo canopies retrieved by the GOST2 model (incorporating leaf clumping), the 4SAIL model and the SNAP tool (both without leaf clumping), respectively, were validated against ground-based LAI estimations, including the direct allometric method and indirect digital hemispherical photograph (DHP) methods. LAIs retrieved by GOST2 show strong agreement with the surrogate truth estimated by the allometric method (R² = 0.79, RMSE = 3.03), but underestimations of retrieved LAIs by 4SAIL and the SNAP tool reach up to 27.6 and 28.8, respectively, due to lack of consideration of leaf clumping. These results indicate the following: (1) Depending on gap analysis-based clumping index (Ω) algorithms, leaf clumping corrections in indirect ground-based LAI estimations are unsuccessful for highly clumped Moso bamboo canopies due to heavy overlapped leaves; (2) LAIs of dense and highly clumped Moso bamboo canopies can be retrieved from satellite remote sensing data through canopy reflectance models with leaf clumping consideration; (3) The misunderstanding of LAI ranges of Moso bamboo canopies by previous studies (2.2–6.5) can be attributed to the application of gap analysis-based Ω for indirect ground-based LAI estimations; and (4) Effective leaf area index (L_e) derived from satellite remote sensing data, and validated using gap analysis-based L_e/Ω, could be erroneously interpreted as LAI. Full article

The feasibility of producing high-quality zinc phosphate cement based on a frit-sintered mixture of ZnO, SiO₂, MgO, and Bi₂O₃ oxides, with the addition of phosphorous slag and an aqueous solution of orthophosphoric acid as the mixing liquid, was demonstrated. The raw materials used for zinc phosphate cement preparation were investigated using various physicochemical analysis methods. It was found that the phosphorous slag contains silicon oxide (37.6%), aluminum oxide (4.49%), calcium oxide (42.4%), magnesium oxide (2.19%), as well as fluorine (1.94%) and calcium fluoride (4.91%). The slag predominantly consists of an amorphous glassy phase with minor inclusions of crystalline components. During the sintering process, the addition of 1.5–3.0 wt.% phosphorous slag to the frit promotes the formation of low-melting eutectics due to the presence of fluorides, resulting in a 100 °C reduction in the sintering temperature. An optimal zinc phosphate cement powder composition was developed, comprising: ZnO—83.0%, MgO—9.0%, SiO₂—3.5%, Bi₂O₃—3.0%, and phosphorous slag—1.5%. The resulting sintered product exhibited a whiteness of 97.8%, which exceeds that of the reference sample by 2.6%. Upon mixing the powder with the mixing liquid, zinc ions are released first, initiating a chemical reaction that leads to the formation of zinc, magnesium, and aluminum phosphates. The compressive strength of the resulting composite cements ranged from 101.8 to 111.9 MPa, fully complying with the requirements for cement grade as specified in GOST 31578-2012. Full article

The importance of assessing the microbiological safety of food products is beyond doubt, which is also true for milk and dairy products. The goal of this work was to evaluate the changes in the composition of the gas phase in milk based on signals from chemical sensors to predict the quantity of the bacteria in the milk samples. The gas phase in raw milk samples and samples during pasteurization, as well as for a standard (a model aqua solution of macronutrients and minerals), was studied using an array of sensors with polycomposite coatings, including those contaminated with E. coli bacteria. Assessment of microbiological indicators was carried out according to GOST in parallel with the gas-phase analysis. The applicability of the results obtained on model systems was assessed using milk samples, including those containing other types of pathogenic microorganisms (Staphylococcus aureus, Klebsiella spp., etc.). It was found that the obtained models can be used to assess the presence and quantity of E. coli in milk at the pasteurization stage. Full article

Zoo conditions are unique for reindeer, since domestic reindeer are not kept in captive facilities like cattle. In the zoo, reindeer are usually surrounded by many different animals that they would never encounter naturally. Thus, they might be infected with new helminths. Numerous petting zoos raise concerns about the safety of tactile interactions for human visitors. Our study is the first large-scale one. Qualitative and quantitative fecal analyses were carried out for 233 reindeer distributed over 50 Russian zoos according to the National Standard of the Russian Federation (GOST R 54627-2011) Ruminant animals—Methods of Laboratory Helminthological Diagnostics. Where possible, DNA analyses of helminths were performed targeting internal transcribed spacer region. As a result, F. hepatica, Paramphistomum sp., Moniezia sp. (including M. expansa), gastrointestinal strongylids (including Nematodirus spp.), Dictyocaulus sp., E. rangiferi, Trichuris sp., and Capillaria sp. were found in 106 (45%) zoo reindeer. All these helminths were previously reported in reindeer and pose no direct danger for humans. The intensity of invasions was mostly low. Fecal examination might be considered as an indirect method for mange diagnostics, as Chorioptes and Demodex mites were found in reindeer fecal samples. The latter may represent a novel species of mite specific for reindeer. Full article

Pollution by active ingredients is one of the most significant and widespread forms of pollution on Earth. Medicines can have a negative impact on ecosystems, and contamination can have unpredictable consequences. An urgent and unexplored task is to study the Lake Baikal ecosystem and its organisms for the presence of trace concentrations of active pharmaceutical ingredients. Our study aimed to conduct a qualitative analysis of active pharmaceutical ingredients, and quantitative analysis of ibuprofen in endemic amphipods of Lake Baikal, using methods of high-performance liquid chromatography and mass spectrometry (HPLC-MS). Acetylsalicylic acid (aspirin), ibuprofen, acetaminophen, azithromycin, dimetridazole, metronidazole, amikacin, spiramycin, and some tetracycline antibiotics were detected in the studied littoral amphipods. We also detected different annual loads of active pharmaceutical ingredients on amphipods. Using the multiple reaction monitoring (MRM) mode mentioned in GOST International Technical Standards, we detected molecules, fragmented as amikacin, chlortetracycline, doxycycline, oxytetracycline, dimetridazole, metronidazole and spiramycin. Thus, we first revealed that invertebrates of Lake Baikal can uptake pharmaceutical contaminants in the environment. Full article

A novel solid-phase synthetic approach was developed to produce a mineral-like composite ceramic based on strontium titanate (SrTiO₃) and yttrium titanate (Y₂Ti₂O₇) matrices for immobilizing radionuclides such as ⁹⁰Sr and its daughter product ⁹⁰Y, as well as lanthanides and actinides, via reactive spark plasma sintering technology (SPS-RS). Using XRD, SEM, and EDS analyses, the sintering kinetics of the initial mixed oxide reactants of composition Y_xSr_1–1.5xTiO₃ (x = 0.2, 0.4, 0.6 and 1) and structure-phase changes in the ceramics under SPS-RS conditions were investigated as a function of Y³⁺ content. In addition, a detailed study of phase transformation kinetics over time as a function of the heating temperature of the initial components (SrCO₃, TiO₂, and Y₂O₃) was conducted via in situ synchrotron XRD heating experiments. The composite ceramic achieved relatively high physicomechanical properties, including relative density between 4.92–4.64 g/cm³, Vickers microhardness of 500–800 HV, and compressive strength ranging from 95.5–272.4 MPa. An evaluation of hydrolytic stability and leaching rates of Sr²⁺ and Y³⁺ from the matrices was performed, demonstrating rates did not exceed 10⁻⁵–10⁻⁶ g·cm⁻²·day⁻¹ in compliance with GOST R 50926-96 and ANSI/ANS 16.1 standards. The leaching mechanism of these components was studied, including the calculation of solution penetration depth in the ceramic bulk and ion diffusion coefficients in the solution. These findings show great promise for radioactive waste conditioning technologies and the manufacturing of radioisotope products. Full article

The paper presents a reliable technology combining sol–gel synthesis and spark plasma sintering (SPS) to obtain SrTiO₃ perovskite-type ceramics with excellent physicomechanical properties and hydrolytic stability for the long-term retention of radioactive strontium radionuclides. The Pechini sol–gel method was used to synthesize SrTiO₃ powder from Sr(NO₃)₂ and TiCl₃ (15%) precursors. Ceramic matrix samples were fabricated by SPS in the temperature range of 900–1200 °C. The perovskite structure of the synthesized initial SrTiO₃ powder was confirmed by X-ray diffraction and thermal analysis results. Scanning electron microscopy revealed agglomeration of the nanoparticles and a pronounced tendency for densification in the sintered compact with increasing sintering temperature. Chemical homogeneity of ceramics was confirmed by energy dispersive X-ray analysis. Physicochemical characteristic studies included density measurement results (3.11–4.80 g·cm⁻³), dilatometric dependencies, Vickers microhardness (20–900 HV), and hydrolytic stability (10⁻⁶–10⁻⁷ g·cm⁻²·day⁻²), exceeding GOST R 50926-96 and ISO 6961:1982 requirements for solid-state matrices. Ceramic sintered at 1200 °C demonstrated the lowest strontium leaching rate of 10⁻⁷ g/cm²·day, optimal for radioactive waste (RAW) isolation. The proposed approach can be used to fabricate mineral-like forms suitable for RAW handling. Full article

This article reports on a simple method for producing high-octane gasoline from CO and H₂ on a Co-Al₂O₃/SiO₂/HZSM-5/Al₂O₃ hybrid catalyst. In the selected pressure range (0.5, 1.0, and 2.0 MPa), it was found that a decrease in pressure and an increase in temperature contribute to an increase in the content of branched hydrocarbons. The optimal technological parameters of the process were determined to ensure high selectivity and productivity for C₅–C₁₀ hydrocarbons: pressure—1.0 MPa, ratio H₂/CO = 2, gas space velocity—1000 h⁻¹, temperature—250 °C. The selectivity for the gasoline fraction is 65.2%, and the ratio of branched to linear hydrocarbons (iso/n index) is 2.3. Under the specified technological conditions, an experimental batch of gasoline fraction (1000 cm³) was produced at the pilot plant during 400 h of continuous operation. The main physicochemical and operational parameters of the experimental gasoline fraction of hydrocarbons have been determined. The octane number determined by the research method according to GOST R 52947-2019 is 78.5 units. Full article

This paper reports a method for the fabrication of mineral-like SrMoO₄ ceramics with a powellite structure, which is promising for the immobilization of the high-energy ⁹⁰Sr radioisotope. The reported method is based on the solid-phase “in situ” interaction between SrO and MoO₃ oxides initiated under spark plasma sintering (SPS) conditions. Dilatometry, XRD, SEM, and EDX methods were used to investigate the consolidation dynamics, phase formation, and structural changes in the reactive powder blend and sintered ceramics. The temperature conditions for SrMoO₄ formation under SPS were determined, yielding ceramics with a relative density of 84.0–96.3%, Vickers microhardness of 157–295 HV, and compressive strength of 54–331 MPa. Ceramic samples demonstrate a low Sr leaching rate of 10⁻⁶ g/cm²·day, indicating a rather high hydrolytic stability and meeting the requirements of GOST R 50926-96 imposed on solid radioactive wastes. The results presented here show a wide range of prospects for the application of ceramic matrixes with the mineral-like composition studied here to radioactive waste processing and radioisotope manufacturing. Full article

Fresh groundwater, as an essential component of global water resources and a special type of mineral wealth, has a whole set of features that affect social infrastructure, the economy and the environmental well-being of the population. At the same time, groundwater is vulnerable and limited despite its replenishable nature and vast reserves. Recently, in some countries, the practice of extracting groundwater resources by private individuals on their territory has been actively spreading, but not in all states. This is considered acceptable and is enshrined in national regulations. Uncontrolled exploitation of aquifers by small water users can affect the safety of ecosystems and the depletion of drinking groundwater reserves. In this regard, the state policy and system for regulating access to groundwater resources for all subsoil users should be based on a well-thought-out concept. This article is devoted to the organizational, economic, and regulatory issues of groundwater extraction by individuals for their own needs in the Russian Federation. A comparative analysis of the state approach to groundwater extraction by private individuals in other states (mainly in the example of Germany and China) is made. The latest trends in legislation in this area are analyzed, shortcomings in the system of state regulation of groundwater use are identified, and mechanisms for legalizing the activities of individual water users are proposed. Global groundwater regulation should be based on rationality, control, safety, protection, sustainability, and future generations’ care. Full article

Precipitation strengthening in titanium-stabilized austenitic stainless steels can improve the hot yield strength, as requested, e.g., for nuclear industry applications. The resulting properties depend mainly on the parameters of the heat treatment and previous forming. The influence of the heat treatment parameters on the development of the microstructure and mechanical properties was determined for steel 08Ch18N10T (GOST). Solution annealing and stabilization with different temperatures and holds were performed on the steel, which was, in delivered condition, stabilized at 720 °C. Heat-treated samples were subjected to static tensile testing at room temperature and at 350 °C, microstructural analysis using light, scanning electron and transmission electron microscopy focused on precipitates, and HV10 hardness testing. The strengthening mechanism and its dependence on the stabilization parameters are described. The results of the experiment show the influence of the state of the input material on the final effect of heat treatment—repeated heat treatment achieved lower-strength characteristics than the initial state, while almost all modes showed above-limit values for the mechanical properties. Stabilization temperatures of 720 to 800 °C were found to be optimal in terms of the achieved hot yield strength. At higher temperatures, slightly lower strengths were achieved, but at significantly shorter dwell times. Full article