Search Results (5,630)

Underreamed anchor bolts, as an emerging anchoring element in geotechnical engineering, operate via a fundamentally distinct load transfer mechanism compared with conventional friction type anchors. The accurate and reliable prediction of their ultimate bearing capacity constitutes a pivotal technological impediment to their broader engineering adoption. Firstly, this paper systematically elucidates the constituent mechanisms of underreamed anchor resistance and their progressive load transfer trajectory. Subsequently, in situ full-scale pull-out experiments are leveraged to decompose the load–displacement response throughout its entire evolution. The multi-stage development law and the underlying mechanisms governing the evolution of anchorage characteristics are thereby elucidated. Based on the experimental dataset, a three-dimensional elasto-plastic numerical model is rigorously established. The model delineates, at high resolution, the failure mechanism of surrounding soil mass and the spatiotemporal evolution of its three-dimensional displacement field. A definitive critical displacement criterion for the attainment of the ultimate bearing capacity of underreamed anchors is established. Consequently, analytical models for the ultimate side frictional stress and end-bearing capacity at the limit state are advanced, effectively circumventing the parametric uncertainties inherent in extant empirical formulations. Ultimately, characteristic parameters of the elasto-plastic branch of the load–displacement curve are extracted. An ultimate bearing capacity prognostic framework, founded on an optimized hyperbolic model, is established. Its superior calibration fidelity to the evolving load–displacement response and its demonstrable engineering applicability are rigorously substantiated. Full article

This paper reports a novel effort to estimate and evaluate the coefficients of Hg transfer across the water/air interface in lakes such as Cane Creek Lake (CCL, Cookeville, TN, USA). This was accomplished by calculating the coefficients (k_w) using the Two-Thin Film (TTF) Model for Hg transfer together with the field-measured data of Hg emission flux (F), dissolved gaseous mercury concentration (DGM), air Hg concentration (C_a), and water temperature for Henry’s coefficient (K_H) obtained from a separate field study at the CCL. The daily mean k_w values range from 0.045 to 0.21 m h⁻¹, with the min. at 0.0025–0.14 and the max. at 0.079–0.41 m h⁻¹, generally higher for the summer, and from 0.0092 to 0.15, with the min. at 0.0032–0.033 and the max. at 0.017–0.31 m h⁻¹, generally lower for the fall and winter, exhibiting an apparent seasonal trend. The highest k_w values occur in August (mean: 0.21, max.: 0.41 m h⁻¹). Our k_w results add to and enrich the aquatic interfacial Hg transfer coefficient database and provide an alternative avenue to evaluate and select the coefficients for the TTF Model’s application. The k_w results are of value in gaining insights into the Hg transfer actually occurring across the water/air interface under environmental influences (e.g., wind/wave, solar radiation). Our k_w results do not show a clear, consistent correlation of k_w with wind/wave effect, nor sunlight effect, in spite of some correlations in sporadic cases. Generally, the k_w values do not exbibit the trends prescribed by the model sensitivity study. The comparisons of our k_w results with those obtained using wind-based transfer models (the Liss/Merlivat Model, the Wanninkhof Model, and the modified linear model) show that they depart from each other. The findings of this study indicate that the TTF Model has limitations and weaknesses. One major assumption of the TTF Model is the equilibrium of the Hg distribution between the air and water films across the water/air interface. The predominant oversaturation of DGM shown by our DGM data evidently challenges this assumption. This study suggests that aquatic interfacial Hg transfer is considerably more complicated, involving a group of factors, more than just wind and wave. Full article

Biologically treated swine farm wastewater still contains high levels of refractory organics, humic substances and antibiotic residues, posing environmental risks and limiting opportunities for water reuse. Wastewater treatment by ozonation alone suffers from low mass transfer efficiency and selective oxidation. To overcome these limitations, a catalytic ozonation process (O₃/Fe²⁺/H₂O₂) was applied and optimized using Response Surface Methodology (RSM) based on single-factor experiments and Central Composite Design (CCD) for advanced swine farm wastewater treatment. The optimal conditions ([O₃] = 25.0 mg/L, [Fe²⁺] = 25.9 mg/L, [H₂O₂] = 41.1 mg/L) achieved a COD removal of 44.3%, which was 86.8% higher than that of ozonation alone, and increased TOC removal to 29.5%, indicating effective mineralization. Biodegradability (BOD₅/COD) of swine farm wastewater effluent increased from 0.01 to 0.34 after the catalytic ozonation treatment. Humic-like and fulvic-like substances were removed by 93.7% and 95.4%, respectively, and antibiotic degradation was significantly accelerated and enhanced. The synergistic process improved ozone utilization efficiency by 33.1% and removed 53.95% of total phosphorus through Fe³⁺-mediated coprecipitation. These findings demonstrate that with catalytic ozone decomposition and production of hydroxyl radicals, the O₃/Fe²⁺/H₂O₂ system effectively integrates enhanced ozone utilization efficiency, radical synergy, and simultaneous pollutant removal, providing a cost-effective and technically feasible strategy for advanced swine farm wastewater treatment and safe reuse. Full article

Electrocoagulation (EC) is a sustainable strategy for wastewater treatment, but the role of hydrodynamics and impeller design remains underexplored. This study assessed the impacts of electrode type (Al, Fe), impeller type (SBT, PBT), treatment time, and the inclusion of zeolite (ECZ) on the efficacy of compost wastewater treatment. The results obtained were also compared with those obtained in the EC treatment of the same wastewater in a reactor equipped with a folding paddle impeller. Key performance indicators included a decrease in chemical oxygen demand (COD), residual turbidity, electrode mass loss, energy consumption, pH, temperature, and settling behaviour. Al electrodes achieved higher COD removal (80–92%) but consumed more energy, while Fe electrodes showed slightly higher electrode mass loss. Zeolite increased residual turbidity but improved the settling behaviour during longer treatments. Fe electrodes led to larger pH shifts, whereas Al electrodes caused higher temperature increases. Compared with the folding paddle impeller, SBT and PBT promoted more favourable pH evolution, slightly higher COD removal, and lower residual turbidity. These advantages could be attributed to enhanced turbulence, mass transfer, and solid–liquid interactions, which enhance coagulant formation and dispersion. L8 Taguchi optimisation identified the addition of zeolite as the main factor influencing COD reduction, while treatment time was key for minimising electrode consumption. The findings demonstrate that impeller selection, combined with process optimisation, contributes to the mechanical process intensification of EC, improving treatment efficiency, electrode durability, and cost-effectiveness. Full article

The hydrogen economy stands at the forefront of the global energy transition, and additive manufacturing (AM) is increasingly recognized as a critical enabler of this transformation. AM offers unique capabilities for improving the performance and durability of hydrogen energy components through rapid prototyping, topology optimization, functional integration of cooling channels, and the fabrication of intricate, hierarchical, structured pores with precisely controlled connectivity. These features facilitate efficient heat and mass transfer, thereby improving hydrogen production, storage, and utilization efficiency. Furthermore, AM’s multi-material and functionally graded printing capability holds promise for producing components with tailored properties to mitigate hydrogen embrittlement, significantly extending operational lifespan. Collectively, these advances suggest that AM could lower manufacturing costs for hydrogen-related systems while improving performance and reliability. However, the current literature provides limited evidence on the integrated techno-economic advantages of AM in hydrogen applications, posing a significant barrier to large-scale industrial adoption. At present, the technological readiness level (TRL) of AM-based hydrogen components is estimated to be 4–5, reflecting laboratory-scale progress but underscoring the need for further development, validation and industrial-scale demonstration before commercialization can be realized. Full article

The role of wall roughness in heat and mass transfer for fully developed viscous flows in square microchannels is investigated here. Since the roughness, which is the key geometrical feature to be investigated, introduces high velocity gradients at the wall, the effect of the viscous dissipation is considered. A fully developed flow in the forced convection regime is assumed. This assumption allows the two-dimensional treatment of the problem; thus, the velocity and temperature fields are simulated on the microchannel cross-section. The boundary roughness is modeled by randomly throwing points around the nominal square cross-section perimeter and by connecting those points to generate a simple polygon. This modification of the nominal square shape of the cross-section influences the velocity and temperature fields, which are computed by employing a finite element method solver. The heat and mass transfer is studied by calculating the Nusselt and the Poiseuille numbers as a function of roughness amplitude at the boundary. Each Nusselt and Poiseuille number is obtained by employing an averaging procedure over a sample of a thousand cases. Full article

Solid oxide electrolysis cells (SOECs) have emerged as a promising technology for efficient energy storage and CO₂ utilization via H₂O–CO₂ co-electrolysis. While most previous studies focused on planar or tubular configurations, this work investigated a novel flat, tubular SOEC design using a comprehensive 3D multi-physics model developed in COMSOL Multiphysics 5.6. This model integrates charge transfer, gas flow, heat transfer, chemical/electrochemical reactions, and structural mechanics to analyze operational behavior and thermo-mechanical stress under different voltages and pressures. Simulation results indicate that increasing operating voltage leads to significant temperature and current density inhomogeneity. Furthermore, elevated pressure improves electrochemical performance, possibly due to increased reactant concentrations and reduced mass transfer limitations; however, it also increases temperature gradients and the maximum first principal stress. These findings underscore that the design and optimization of flat tubular SOECs in H₂O–CO₂ co-electrolysis should take the trade-off between performance and durability into consideration. Full article

To address the challenges of complex composition, high chemical oxygen demand (COD) content, and the difficulty of treating organic wastewater from brewery wastewater, as well as the limitations of traditional Fenton technology, including low catalytic activity and high material costs, this study proposes the use of biochemical sludge as a raw material. Coupled with iron salt activation and mechanical ball milling technology, a low-cost, high-performance iron-doped mesoporous nano-sludge biochar material is prepared. This material was employed as a particle electrode to construct a three-dimensional electro-Fenton system for the degradation of organic wastewater from sauce-flavor liquor brewing. The results demonstrate that the sludge-based biochar produced through this approach possesses a mesoporous structure, with an average particle size of 187 nm, a specific surface area of 386.28 m²/g, and an average pore size of 4.635 nm. Iron is present in the material as multivalent iron ions, which provide more electrochemical reaction sites. Utilizing response surface methodology, the optimized treatment process achieves a maximum COD degradation rate of 71.12%. Compared to the control sample, the average particle size decreases from 287 μm to 187 nm, the specific surface area increases from 44.89 m²/g to 386.28 m²/g, and the COD degradation rate improves by 61.1%. Preliminary investigations suggest that the iron valence cycle (Fe²⁺/Fe³⁺) and the mass transfer enhancement effect of the mesoporous nano-structure are keys to efficient degradation. The Fe-O-Si structure enhances material stability, with a degradation capacity retention rate of 88.74% after 30 cycles of use. When used as a particle electrode to construct a three-dimensional electro-Fenton system, this material demonstrates highly efficiency in organic matter degradation and shows promising potential for application in the treatment of organic wastewater from sauce-flavor liquor brewing. Full article

To address environmental pollution issues and optimize the utilization of waste biomass resources, this study proposes a novel eco-friendly sound-absorbing material based on maple leaf waste and tests its sound absorption performance. The fibers were extracted from maple leaf waste through a wet decomposition and grinding process. Metallurgical microscopy was employed to observe the microstructural characteristics of maple leaf fibers to identify the potential synergistic effect. The effects of two key factors—sample thickness and mass density—on sound absorption performance were investigated. The sound absorption coefficients were measured using the transfer function method in a dual-microphone impedance tube to evaluate their sound-absorbing performance. Experimental results demonstrate that the prepared maple leaf fibers, as acoustic materials, exhibit excellent acoustic performance across a wide frequency range, with an average sound absorption coefficient of 0.7. Increasing sample thickness improves the sound absorption coefficient in low- and mid-frequency ranges. Additionally, increased sample mass density was found to enhance acoustic performance in low- and mid-frequency bands. This study developed an eco-friendly material with lightweight and efficient acoustic absorption properties using completely biodegradable maple leaf waste. The results provide high-performance, economical, and ecologically sustainable solutions for controlling building and traffic noise while promoting the development of eco-friendly acoustic materials. Full article

Coke is an essential raw material in the blast furnace (BF) ironmaking process. Its moisture content significantly impacts BF ironmaking production. This study employs a coupled Computational Fluid Dynamics–Discrete Element Method (CFD-DEM) approach to simulate the drying process of wet coke within a coke silo (CS) dryer. Initially, the model was validated by comparing numerical results with experimental data from the literature. Subsequently, it investigated the gas flow dynamics, heat and mass transfer characteristics, and differences in drying behaviour across distinct dryer zones. Finally, the effects of inlet gas velocity and inlet gas temperature on the drying process were systematically quantified. Simulation results reveal that the bottom of the CS dryer exhibits a low-velocity laminar state, while the middle and upper regions display intense gas flow motion. Consequently, the bottom region exhibits insufficient particle drying in comparison to other zones, with the average particle moisture content decreasing by less than 20%. Under the continuous heat exchange between the hot gas and the particles, the moisture content of the particles decreases rapidly. Based on the drying rate behaviour, the drying process exhibits the following three different stages: the pre-heating period, the constant-rate period, and the falling-rate period. Compared to zones 1 and 3, zone 2 exhibits higher temperatures due to its high heat transfer efficiency, which significantly promotes a reduction in particle moisture content. An increase in inlet gas velocity enhances the particle drying rate and heat flux, accelerates moisture reduction, and raises the temperature. The impact of inlet gas velocity is most pronounced after the constant-rate period, with particle drying uniformity decreasing as the inlet gas velocity increases, consequently leading to a decline in drying quality. Increasing inlet gas temperature significantly increases particle temperature and heat flux throughout the drying period and accelerates the high-rate drying stage. These findings provide fundamental insights for further understanding and studying the coke drying process. Full article

This study experimentally investigates the boiling heat transfer characteristics of R32 and R410A refrigerants in heat exchangers, systematically analyzing the effects of tube thickness, saturation temperature, latent heat, liquid-phase density, and viscosity. The average boiling heat transfer coefficients (HTCs) of R32 and R410A were compared across varying mass flow rates and saturation temperatures. The results reveal that, independent of tube thickness, the boiling HTC of R32 exhibits a non-monotonic increase followed by a decrease with rising mass flow rate. Additionally, elevated saturation temperatures reduced vaporization latent heat, liquid-phase density, and gas-phase viscosity, while the flow pattern may also change. Meanwhile, R32 demonstrated superior boiling heat transfer performance compared to R410A under equivalent conditions. Furthermore, the correlation is proposed to predict the HTCs, indicating ±10% prediction error. This study provides critical insights for optimizing refrigeration systems and advancing heat exchanger modeling frameworks. Full article

Background: This study investigated sex differences in foot arch structure and function, and their impact on postural control and energy flow during dynamic tasks. Findings aim to inform sex-specific training, movement assessment, and injury prevention strategies. Methods: A total of 108 participants (53 males and 55 females) underwent foot arch morphological assessments and performed a sit-to-stand (STS). Motion data were collected using an infrared motion capture system, three-dimensional force plates, and wireless surface electromyography. A rigid body model was constructed in Visual3D, and joint forces, segmental angular and linear velocities, center of pressure (COP), and center of mass (COM) were calculated using MATLAB. Segmental net energy was integrated to determine energy flow across different phases of the STS. Results: Arch stiffness was significantly higher in males. In terms of postural control, males exhibited significantly lower mediolateral COP frequency and anteroposterior COM peak velocity during the pre-seat-off phase, and lower COM displacement, peak velocity, and sample entropy during the post-seat-off phase compared to females. Conversely, males showed higher anteroposterior COM velocity before seat-off, and greater anteroposterior and vertical momentum after seat-off (p < 0.05). Regarding energy flow, males exhibited higher thigh muscle power, segmental net power during both phases, and greater shank joint power before seat-off. In contrast, females showed higher thigh joint power before seat-off and greater shank joint power after seat-off (p < 0.05). Conclusions: Significant sex differences in foot arch function influence postural control and energy transfer during STS. Compared to males, females rely on more frequent postural adjustments to compensate for lower arch stiffness, which may increase mechanical loading on the knee and ankle and elevate injury risk. Full article

Micron-sized near-spherical α-Al₂O₃ powders are widely used as thermal fillers due to their high thermal conductivity, high packing density, good flowability, and low cost. During the high-temperature calcination, the resulting α-Al₂O₃ powders often exhibit an aggregated worm-like morphology owing to limitations in solid-state mass transfer. Researchers have employed various mineralizers to regulate the morphology of α-Al₂O₃ powders; however, the preparation of micron-sized highly spherical α-Al₂O₃ powders via solid-state calcination is still a great challenge. In this work, micron-sized near-spherical α-Al₂O₃ powders were synthesized through high-temperature calcination using hydratable alumina (ρ-Al₂O₃) as precursor with water-soluble mineralizer ammonium fluoroborate (NH₄BF₄). ρ-Al₂O₃ can undergo a hydration reaction with water to form AlO(OH) and Al(OH)₃ intermediates, serving as an excellent precursor. With the addition of 0.1 wt% NH₄BF₄, the product exhibits an optimal near-spherical morphology. Excessive addition (>0.2 wt%), however, significantly promotes the transformation of α-Al₂O₃ from a near-spherical to a plate-like structure. Further studies reveal that the introduction of NH₄BF₄ not only modulates the crystal morphology but also effectively reduces the content of sodium impurities in the powder through a high-temperature volatilization mechanism, thereby enhancing the thermal conductivity of the powder. It is shown that the thermal conductivity of the micron-sized α-Al₂O₃/ epoxy resin composites reaches 1.329 ± 0.009 W/(m·K), which is 7.4 times that of pure epoxy resin. Full article

This study evaluates the impact of mineralogy, elemental composition, and reaction pathways on hydrogen (H₂) generation in seven ultramafic and mafic (basaltic) rocks. Experiments were conducted under typical low-temperature hydrothermal conditions (150 °C) and captured early and evolving stages of fluid–rock interaction. Pre- and post-interactions, the solid phase was analyzed using X-ray Diffraction (XRD) and X-ray Photoelectron Spectroscopy (XPS), while Inductively Coupled Plasma Mass Spectrometry (ICP-MS) was used to determine the composition of the aqueous fluids. Results show that not all geologic H₂-generating reactions involving ultramafic and mafic rocks result in the formation of serpentine, brucite, or magnetite. Our observations suggest that while mineral transformation is significant and may be the predominant mechanism, there is also the contribution of surface-mediated electron transfer and redox cycling processes. The outcome suggests continuous H₂ production beyond mineral phase changes, indicating active reaction pathways. Particularly, in addition to transition metal sites, some ultramafic rock minerals may promote redox reactions, thereby facilitating ongoing H₂ production beyond their direct hydration. Fluid–rock interactions also regenerate reactive surfaces, such as clinochlore, zeolite, and augite, enabling sustained H₂ production, even without serpentine formation. Variation in reaction rates depends on mineralogy and reaction kinetics rather than being solely controlled by Fe oxidation states. These findings suggest that ultramafic and mafic rocks may serve as dynamic, self-sustaining systems for generating H₂. The potential involvement of transition metal sites (e.g., Ni, Mo, Mn, Cr, Cu) within the rock matrix may accelerate H₂ production, requiring further investigation. This perspective shifts the focus from serpentine formation as the primary driver of H₂ production to a more complex mechanism where mineral surfaces play a significant role. Understanding these processes will be valuable for refining experimental approaches, improving kinetic models of H₂ generation, and informing the site selection and design of engineered H₂ generation systems in ultramafic and mafic formations. Full article

A 75-year-old patient was transferred to the oncology department due to the discovery of a large pelvic tumor compressing the femoral neurovascular bundle suspected to be of malignant origin. Further investigation revealed a rare complication related to a 27-year-old total hip arthroplasty (THA). The final diagnosis was a severe adverse local tissue reaction (ALTR) resulting from excessive implant wear—first from a metal-on-metal (MoM) bearing and later exacerbated by a revision to a metal-on-polyethylene (MoP) articulation. The clinical course was further complicated by periprosthetic joint infection (PJI). The patient underwent extensive tumor-like mass resection followed by two-stage revision arthroplasty. Despite these interventions, infection persisted, ultimately necessitating joint resection. This case highlights the rare but serious convergence of dreaded orthopedic complications (ALTR and PJI). It underscores the diagnostic challenge posed by wear-induced pseudotumors, which are rare even among arthroplasty specialists and are often unfamiliar to oncologists. This case illustrates the importance of early orthopedic evaluation, maintaining a high index of suspicion in atypical presentations, and invites further discussion about the interplay between ALTRs and infection risk in arthroplasty patients. Full article