Search Results (35)

This study aims to bridge the critical knowledge gap in understanding the dynamic microstructural evolution during high-solid-fraction semi-solid rheo-die casting process, including slurry preparation (0.1–0.3 K/s) and rheo-die casting (10–150 K/s). A novel phase-field model coupling continuous cooling with explicit nucleation was developed, enabling the dynamic simulation of continuous solidification microstructure evolution, considering two-stage cooling rate transition characteristics. Integrated the Swirled Enthalpy Equilibration Device (SEED) slurry preparation and graded-cooling mold experiments established variable cooling rate and solid fraction conditions for quantitative analysis of α-Al morphological evolution during rheo-die casting solidification. Through experimental and simulation investigations of the Al-7Si alloy, it is concluded that during Stage I slurry preparation, the primary α₁-Al phase coarsened due to Ostwald ripening. In Stage II rheo-die casting, primary α₁-Al undergoes continued growth under a moderate cooling rate (15 K/s). Meanwhile, secondary α₂-Al formation exhibits a cooling-rate and solid fraction dependence: a high cooling rate (150 K/s) promotes explosive nucleation with the volume fraction decreasing from 4.78% to 0.33% as the solid fraction rises, whereas a mid-cooling rate (15 K/s) substantially suppresses its formation. Mechanistically, a high cooling rate promotes solute trapping, which intensifies constitutional undercooling, thereby elevating both the nucleation and growth driving forces to facilitate the formation of secondary α₂-Al, whereas higher solid fractions restrict secondary phase formation by narrowing the solidification windows from 22 °C to 7 °C. Full article

Sludge is a semi-solid waste generated during the process of wastewater treatment. Due to the addition of polymerized ferric chloride in the flocculation process, the sludge produced by the sewage treatment plant in Liaocheng Jiaming Industrial Park contains a high content of iron oxide. In this paper, chemical analysis and particle size analysis of local sludge and sludge ash were conducted. In order to assess the potential of substituting cement as cementitious material with different dosages of sludge or sludge ash with high iron oxide content, setting time, compressive strength, microscopic analysis using microscopic testing (XRD, TG/DTG, SEM) and a toxicity characteristic leaching procedure (TCLP) were analyzed. These procedures determined the physical properties, compressive strength, hydration products, microstructure, and heavy metal contaminants of cement slurries replaced by local sludge or sludge ash with different dosages of high iron oxide content. The results show that less than 5% of local sludge or sludge ash can be incorporated into cement slurry as an alternative cementitious material for solid waste disposal. Full article

To improve the flow mass transfer inside the electrodes and the efficiency of an all-iron redox flow battery, a semi-solid all-iron redox flow battery is presented experimentally. A slurry electrode is designed to replace the traditional porous electrode. Moreover, the effects of an additional external magnetic field are further investigated in the semi-solid battery experiment. The results show that the mass transfer of the slurry in the battery flow channel and the prolonged discharge time are significantly affected by the additional external magnetic fields. In addition, a three-dimensional model of the semi-solid all-iron redox flow battery is presented in detail, and it is verified to be reliable by experimental data. The simulation results show that the ion concentration distributions in the battery become more uniform with the increase in the flow rate and the initial concentration. Furthermore, it is also found that the size of the flow channel influences the mass transfer efficiency of the slurry. After optimizing the flow channel, it is found that when the flow channel length of the slurry inlet and outlet section is 2 cm, the operating efficiency of the semi-solid battery shows an increasing trend. This work provides comprehensive insight into the improvement of the performances of flow batteries, which will be conducive to the practical application of flow batteries. Full article

In this paper, the ultrasonic vibration treatment (UVT) technique was used to prepare a SnSbCu11-6 alloy semi-solid slurry, and the effects of ultrasonic power on its microstructure size, distribution and properties were studied. The results show that the UVT technique significantly refines the Cu6Sn5 phase and SnSb phase and improves their distribution uniformity. Interestingly, the second SnSb phase is also well refined to nearly 100 °C below the melting point; furthermore, the morphology is transformed from coarse petal-like to fine regular cubic, and the average grain size is refined to 48.8 ± 8.8 μm. The alloy’s comprehensive properties are best when the ultrasonic power is 1200 W. The yield strength, tensile strength, elongation and microhardness reach 60.6 MPa, 70.3 MPa, 4.9% and 27.4 HV, respectively, which represent increases of 4.7%, 6.0%, 113% and 23.4%, respectively, compared with conventional liquid casting. This may be attributed to the grain size refinement and distribution uniformity enhancement of the Cu6Sn5 phase and the SnSb phase. This work provides a feasible and effective method for the preparation of high-performance tin-based babbitt alloys by UVT technology. Full article

Erectile dysfunction (ED) refers to the inability of the penis to maintain a firm erection during sexual activity. Mucuna, or M. pruriens, contains levodopa, a compound showing promise in ED treatment. However, formulating Mucuna extract into tablet dosage forms is challenging due to its semisolid nature. This study aimed to develop sustained-release tablets containing Mucuna extract via semisolid extrusion 3D printing. Eudragit RS PO (Eudragit) served as a sustained-release polymer, with poly (vinyl alcohol) (PVA) as a co-polymer for forming the tablet matrices. This study had the following two main phases: screening, which identified the factors affecting the printability, and optimization, which focused on the factors influencing the levodopa release and its consistency. The results showed that both the polymeric solid percentage content (PSPC) in the semisolid slurry and the Eudragit-PVA ratio significantly affected the printability. All of the formulations were printable, and the PSPC and Eudragit-PVA ratios were incorporated into the optimized model. The desired formulation, achieving targeted levodopa release and consistency, had a PSPC of 58.8% and a Eudragit-PVA ratio of 2.87:1. In conclusion, semisolid extrusion 3D printing guided by the design of experiments (DoE) proved feasible for producing reliable 3D-printed tablets with consistent active ingredients and desired release rates. Full article

Nowadays it is common to see the production of complex and critical automotive and aeronautical components reduced in weight for energy efficiency using light alloys with improved microstructural and mechanical properties. The casting processes involved in this trend are strong; in this study, an optimized design of a vertical serpentine channel and a novel design of a horizontal serpentine channel to produce semi-solid slurry (S2S) with thixotropic behavior by self-stirring for rheocasting of A380 and A356 alloys are tested. Simultaneously, chilling during solidification, flow development, and shearing on the alloys to improve the performance of solid fractions and self-stirring at high shear rate are applied. The effects of these conditions on the modification of the morphology transition of the α(Al) phase from dendrite to equiaxed grain are discussed. The results suggest the ability of the mentioned processes to promote the morphological transition of the primary solid due to the produced equiaxed grains of α(Al) phase having sizes between 25–50 µm from A380 alloy processed by vertical self-stirring. On the other hand, the treatment of the A356 alloy using the new horizontal serpentine channel produces equiaxed grains with an average size of 39 µm. Unexpected Si crystals, trapped in the α(Al) phase using both methods with both alloys, are detected. The applied operation parameters were aided by gravity-pouring close to the liquidus temperature, and the obtained microstructural results show the ability for S2S to form alongside thixotropic behavior and non-dendritic solidification by mean of self-stirring in the serpentine channels, suggesting the potential for further experiments under die-casting conditions. Full article

We propose a methodology for the rheological characterization of a semisolid metal slurry using experimental squeeze-flow data. The slurry is modeled as a structural thixotropic viscoplastic material, obeying the regularized Herschel–Bulkley constitutive equation. All rheological parameters are assumed to vary with the structure parameter that is governed by first-order kinetics accounting for the material structure breakdown and build-up. The squeeze flow is simulated using finite elements in a Lagrangian framework. The evolution of the sample height has been studied for wide ranges of the Bingham and Reynolds numbers, the power-law exponent as well as the kinetics parameters of the structure parameter. Systematic comparisons have been carried out with available experimental data on a semisolid aluminum alloy (A356), where the sample is compressed from its top side under a specified strain of 80% at a temperature of 582 °C, while the bottom side remains fixed. Excellent agreement with the experimental data could be achieved provided that at the initial instances (up to 0.01 s) of the experiment, the applied load is much higher than the nominal experimental load and that the yield stress and the power-law exponent vary linearly with the structure parameter. The first assumption implies that a different model, such as an elastoviscoplastic one, needs to be employed during the initial stages of the experiment. As for the second one, the evolution of the sample height can be reproduced allowing the yield stress to vary from 0 (no structure) to a maximum nominal value (full structure) and the power-law exponent from 0.2 to 1.4, i.e., from the shear-thinning to the shear-thickening regime. These variations are consistent with the internal microstructure variation pattern known to be exhibited by semisolid slurries. Full article

There are multiple routes to prepare semi-solid slurries with a globular microstructure for semi-solid forming. The variations in the microstructure of semi-solid slurries prepared using different routes may lead to significant differences in the flow behavior and mechanical properties of rheo-diecasting parts. Therefore, it is crucial to have a comprehensive understanding of the microstructure evolution associated with different slurry preparation routes and their resulting effects. In this study, the gas-induced semi-solid process (GISS) and the swirl enthalpy equilibrium device (SEED) routes were employed to prepare semi-solid Al-Si-Mg slurries for their simplicity and productivity in potential industrial applications. The prepared slurries were then injected into the shoot sleeves of a high-pressure die casting (HPDC) machine to produce tensile test bars. Subsequently, the bars underwent T6 treatment to enhance their mechanical properties. The microstructure, segregation, and mechanical properties of the samples were investigated and compared with those of conventional HPDC. The results indicated that the GISS and SEED can produce semi-solid slurries containing a spherical α-Al primary phase, as opposed to the dendritic structure commonly found in conventional castings. The liquid fraction had a significant effect on the flow behavior, resulting in variations in liquid segregation and mechanical properties. It was observed that a higher solid fraction (>75%) had a suppressing effect on surface liquid segregation. In addition, the tendency for liquid segregation gradually increased along the filling direction due to the special flow behavior of the semi-solid slurry with a low solid fraction. Furthermore, under the same die-casting process parameters, the conventional HPDC samples exhibit higher yield stress (139 ± 3 MPa) compared to SEED-HPDC and GISS-HPDC samples, which may be attributed to the small grain size and the distribution of eutectic phases. After undergoing the T6 treatment, both SEED-HPDC and GISS-HPDC samples showed a significant improvement in yield and tensile strength. These improvements are a result of solution and precipitation strengthening effects as well as the spheroidization of the eutectic Si phase. Moreover, the heat-treated SEED-HPDC samples demonstrate higher ultimate strength (336 ± 5 MPa) and elongation (13.7 ± 0.3%) in comparison to the GISS-HPDC samples (307 ± 4 MPa, 8.8 ± 0.2%) after heat treatment, mainly due to their low porosity density. These findings suggest that both GISS-HPDC and SEED-HPDC processes can be utilized to produce parts with favorable mechanical properties by implementing appropriate heat treatments. However, further investigation is required to control the porosities of GISS-HPDC samples during heat treatment. Full article

A semi-solid route is expected to be a fabrication method that can fabricate aluminum alloy foams with a variety of mechanical properties, but the allowance fluctuation of the fabrication conditions of aluminum alloy foams with high reproducibility is not clear. The objective of this study was to reveal the allowance fluctuation between the setting temperature and the actual temperature of the melt to fabricate stable foams, having pores with small pores and high circularity, and the influence of the increasing volume fraction of the solid on the pore morphology. Al-Si alloy foams were fabricated five times by adding a blowing agent into a semi-solid slurry under the same setting fabrication conditions, such as the temperature and concentration of oxygen in the atmosphere. The results of small relative standard deviations of pore diameter and circularity indicated that the conducted fabrication process had high reproducibility, even if the volume fraction of the solid changed in a range of 5%. When the volume fraction of the solid exceeds the minimal fraction of primary crystals for prevention of drainage, the clogging effect works more efficiently because the ratio of clogged cell walls increases. Additionally, the preferred range of the volume fraction of the solid for the fabrication of stable foam was revealed to be around 15% to 35%. Full article

The non-dendritic microstructure plays a crucial role in determining the rheological properties of semi-solid alloys, which are of the utmost importance for the successful industrial application of the thixoforging process. To further understand the impact of the reheating process on the evolution of microstructure and thixotropic deformation behavior in the semi-solid state, a hot extruded and T6 treated 7075 aluminum alloy was reheated to the selected temperature ranges using varying heating rates. Subsequently, thixo-compression tests were performed. The study found that during reheating and isothermal holding, the elongated microstructure of the as-supplied alloy can transform into equiaxed or spherical grains. The presence of recrystallized grains was found to be closely linked to the penetration of the liquid phase into the recrystallized grain boundaries. Furthermore, it was observed that higher heating rates resulted in smaller grain sizes. The thixotropic flow behavior of the alloy with various microstructures was analyzed using the true stress–strain curves obtained by thixo-compression experiments, which exhibited three stages: a rapid increase in true stress to a peak value, followed by a decrease in true stress and a steady stress until the end of compression. The stress fluctuated with strain during the formation of the slurry at a strain rate of 10 s⁻¹, indicating the significant role of strain rate in material flow during semisolid formation. Full article

Despite the dozens of earlier research verifications, the contribution of shearing of molten metallic alloys during their solidification to grain formation is still ambiguous. Also, modeling of this phenomenon has received very little attention. Experiments were conducted in this study to investigate the effect of the shear rate on the density, size, and shape factor of the formed grains up to a solid fraction of 0.15 for the solidifying A356 aluminum alloy in the coaxial cylinder viscometer. The rheology of the formed semisolid slurry was studied as well. Results exhibited morphological evolution and grain refinement. The grain number density increased from 5 × 10⁸ m⁻³ in the absence of melt shearing to reach 4 × 10⁹ m⁻³ at the shear rate of 250 s⁻¹. Also, the shape factor was improved to reach 0.78. Based on the experimental investigations, the grain number density under shearing was correlated to the shear rate and the grain number density in the absence of shearing via an empirical formula. A shear-dependent grain multiplication factor was deduced. The alloy exhibited a shear-thinning behavior where the viscosity obeyed the power law with a constant and an exponent of 0.9264 and 0.468, respectively. Moreover, the measured data were fitted to several proposed viscosity models and the model of Hirai et al. showed the best fit; therefore, it was recommended for predicting the viscosity of semisolid slurries. Full article

In this study, an enclosed cooling slope channel (ECSC) was used to produce a semi-solid slurry of the 7075 aluminum alloy. The effects of the pouring temperature and the rate of cooling water on the microstructure of the semi-solid slurry were studied. The microstructure, solidification behavior, mechanical properties, and fracture mechanism of rheological squeeze casting (Rheo-SC) and liquid squeeze casting (LSC) samples were compared. The results indicate that lowering the pouring temperature and increasing the rate of cooling water can refine the crystals of the semi-solid slurry. The best process is a pouring temperature of 670 °C and a rate of cooling water of 200 L/h. The microstructure of the LSC samples was made up of coarse dendritic crystals, but the microstructure of the Rheo-SC samples was made up of almost spherical primary α₁-Al and refined secondary α₂-Al under this method. The ultimate tensile strength, yield strength, and elongation of the Rheo-SC samples were 238 MPa, 151 MPa, and 5.2%, respectively, which were 10%, 10.5%, and 44.4% higher than those of the LSC sample. The key factor contributing to the increased performance of the Rheo-SC samples is the combination of decreased casting flaws, strengthened grain refinement, and improved segregation. Full article

The microstructure plays a key role in the mechanical properties of hyper-eutectic Al-Si alloys. In this study, we investigate the microstructural evolution of rheo-die-casting (RDC) on the Al-15Si-4Cu-0.5Mg alloy using a mechanical rotational barrel system. Our findings demonstrate that higher rotational speed and pouring temperature reduce the size and roundness of primary Si particles in the semisolid slurry. Additionally, during RDC, the dendritic aluminum matrix and skeletal iron-containing inter metallics are sheared off, leading to a more uniform and dispersed Al₂Cu phase. Ultimately, our rheo-diecasting results indicate the formation of a near globular aluminum matrix, fine primary Si particles, and a homogeneous Al₂Cu phase, thus highlighting the efficacy of this processing method for improving the microstructure and properties of the Al-15Si-4Cu-0.5Mg alloy. We suggest that these results hold promise for enhancing the quality of aluminum-based alloys in various industrial applications. Full article

The thixo process has the benefit of producing a semi-solid material in which fine primary α-Al grains are uniformly distributed. However, it also has the disadvantage of a costly raw material billet. In this study, a semi-solid slurry was prepared from the rheo process by cooling and electromagnetic stirring, and then a billet for the thixo process was manufactured through an upsetting process with semi-solid slurry. Then, the billet was reheated (thixo process) to make a semi-solid state, and then a final sample was manufactured through a forming process. In both A356 and A6061 materials, the equivalent diameter of the primary α-Al grains became smaller and the roundness became close to one throughout rheo, upsetting, thixo, and forming processes. Due to the refinement and spheroidizing effect of the primary α-Al grains, the tensile strength was improved by each process, and the elongation was slightly decreased. However, after T6 heat treatment, the tensile strength of A356 was decreased, but the elongation was greatly improved. In the case of A6061, on the other hand, the tensile strength was significantly improved, and its elongation decreased after T6 heat treatment. Full article

Al-7Si-0.5Mg aluminum alloy semi-solid slurry with good spherical grains was prepared by gas induced semi-solid process (GISS) and the effects of both holding time and medium alloy addition on the microstructure of the semi-solid slurry were investigated. These two parameters have a great influence on the solid fraction, the size and the sphericity of the grains. With holding time increased from 85 s to 270 s, the solid phase fraction of the semi-solid slurry decreased from ~0.77 to ~0.67, the average grain size increased from ~95 μm to ~225 μm and the average shape factor decreased from ~0.80 to ~0.33. When medium alloy addition varied in the range of 0.5–2.0 wt%, a better slurry microstructure was obtained at about 1.5 wt%. Compared with the conventional liquid die-casting, the semi-solid die-casting improved the mechanical properties of tensile bars; yield strength, tensile strength and elongation of tensile bars reached ~240 MPa, ~307 MPa and ~8.8% after heat treatment, respectively. In conclusion, GISS process can prepare the semi-solid slurry with uniform and round microstructure, and the semi-solid die-casting can improve mechanical properties of Al-7Si-0.5Mg aluminum alloy. Full article