Thin-Film Synthesis, Characterization and Properties

A special issue of Coatings (ISSN 2079-6412). This special issue belongs to the section "Thin Films".

Deadline for manuscript submissions: 30 November 2024 | Viewed by 44627

Special Issue Editor


E-Mail Website
Guest Editor
School of Engineering and Technology, College of Science and Engineering, Central Michigan University, Mount Pleasant, MI 48859, USA
Interests: Biomaterials; Titanium Oxide Nanoparticles/Nanotubes; Thin Films; Graphene Based Nanocomposites; Magnetic Properties of Iron Oxide; Piezoelectric Materials; Surface Engineering; Photocatalysis; Electrochemistry
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

Thin film is an important field in materials science, electrical engineering, and applied solid state physics. Advances in thin films throughout this century have enabled a wide range of technological breakthroughs in the fields of surface engineering, corrosion, biomaterials, energy generation and storage, microfabrication, computer manufacturing, and physical devices.

This Special Issue invites manuscripts on the synthesis, fabrication, processing, characterization, properties, and applications of thin films.

In particular, the topics of interest include but are not limited to:

  • Synthesis and fabrication;
  • Characterization and applications;
  • Surfaces and interfaces;
  • Nanomechanics of thin films;
  • Properties of thin films;
  • Thin film devices.

Prof. Dr. Waseem Haider
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Coatings is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • Surface engineering
  • Coatings
  • Vapor deposition
  • Surface characterization

Benefits of Publishing in a Special Issue

  • Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
  • Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
  • Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
  • External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
  • e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.

Further information on MDPI's Special Issue polices can be found here.

Published Papers (23 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

14 pages, 9409 KiB  
Article
The Effects of Nitrogen Content on the Mechanical and Tribological Properties of CrTaWNx Thin Films
by Li-Chun Chang, Li-Zhu Wang and Yung-I Chen
Coatings 2024, 14(8), 939; https://doi.org/10.3390/coatings14080939 - 26 Jul 2024
Cited by 1 | Viewed by 676
Abstract
In the study described herein, CrTaWNx thin films were deposited on Si and 304 stainless-steel (SUS304) substrates through magnetron co-sputtering using CrW and Ta targets. The nitrogen flow ratio (fN2 = [N2/(N2 + Ar)]) was adjusted to [...] Read more.
In the study described herein, CrTaWNx thin films were deposited on Si and 304 stainless-steel (SUS304) substrates through magnetron co-sputtering using CrW and Ta targets. The nitrogen flow ratio (fN2 = [N2/(N2 + Ar)]) was adjusted to 0.05, 0.2, 0.4, and 0.5 to fabricate CrTaWNx films with various N contents. The CrTaWNx films prepared at a low fN2 of 0.05 exhibited a low stoichiometric ratio x of 0.16 and a nanocrystalline structure. In contrast, the CrTaWNx films fabricated at an fN2 of 0.2–0.5 exhibited x values of 0.42–0.62 and formed a face-centered cubic phase. The nanocrystalline (Cr0.34Ta0.20W0.46)N0.16 film exhibited mechanical properties and wear resistances that were inferior to those of the crystalline CrTaWNx thin films. A (Cr0.38Ta0.15W0.47)N0.55 film exhibited a hardness of 25.2 GPa, an elastic modulus of 289 GPa, and a low wear rate of 0.51 × 10−5 mm3/Nm. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

12 pages, 2812 KiB  
Article
Polarization-Dependent Plasmon Coupling in Gold Nanoparticles and Gold Thin-Film Systems
by Feng Shan, Yanyan Zhu and Jingyi Huang
Coatings 2024, 14(6), 746; https://doi.org/10.3390/coatings14060746 - 13 Jun 2024
Viewed by 916
Abstract
The characteristics of gap plasmon formed by nanoparticle-on-mirror (NPOM) structures composed of metal nanoparticles (MNPs) and metal thin films have aroused interest for use in various optoelectronic devices. The resonance enhancement characteristics in the gap region of an NPOM structure composed of gold [...] Read more.
The characteristics of gap plasmon formed by nanoparticle-on-mirror (NPOM) structures composed of metal nanoparticles (MNPs) and metal thin films have aroused interest for use in various optoelectronic devices. The resonance enhancement characteristics in the gap region of an NPOM structure composed of gold nanoparticles and gold thin films are simulated theoretically by the finite element method (FEM). The resonant spectrum obtained by the internal coupling effect of the gap can be flexibly controlled by the polarization of incident light and the thickness of the dielectric layer between the MNPs and the metal thin films. We study the resonance spectra of polarization-dependent gold ellipsoidal nanoparticles (GENPs) and gold thin films in the gap region of an NPOM structure. The GENPs and gold thin films are separated by a dielectric layer with a refractive index of 1.36. We observe that the intensity of the resonance electric field in the gap region is inversely proportional to the polarization angle. Similarly, the intensity of the local electric field resonance peak in the gap region is inversely proportional to the thickness of the dielectric layer. When the thickness of the dielectric layer is 0.3 nm and the polarization angle is 0°, the best resonant electric field intensity of 2200 V/m is obtained in the gap region of the NPOM structure (the power of incident light is 1 mW). Finally, the resonant peak wavelength of the electric field in the gap region of the NPOM structure is also controlled by the polarization angle of the incident light and the thickness of the dielectric layer. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

14 pages, 14702 KiB  
Article
The Effect of Deposition Temperature on TiN Thin Films for the Electrode Layer of 3D Capacitors Prepared by Atomic Layer Deposition
by Xingyu Chen, Jing Zhang, Lingshan Gao, Faqiang Zhang, Mingsheng Ma and Zhifu Liu
Coatings 2024, 14(6), 724; https://doi.org/10.3390/coatings14060724 - 5 Jun 2024
Viewed by 1283
Abstract
The TiN thin film is considered a promising electrode layer for 3D capacitors. In this study, TiN thin films were prepared on Si substrates using atomic layer deposition (ALD) at various temperatures from 375 °C to 475 °C. The crystallization behavior, microstructure, and [...] Read more.
The TiN thin film is considered a promising electrode layer for 3D capacitors. In this study, TiN thin films were prepared on Si substrates using atomic layer deposition (ALD) at various temperatures from 375 °C to 475 °C. The crystallization behavior, microstructure, and conductance properties of those TiN thin films were investigated. The resistivity of TiN thin films deposited on Si wafers can reach as low as 128 μΩ·cm. TiN thin films showed lower resistivity and worse uniformity with the deposition temperature increasing. In addition, the aging of TiN thin films may weaken the device performance. Optimized deposition parameters were found and full-coverage deposition of thin films on the wall of deep holes with an aspect ratio of approximately 14 has been successfully achieved. The results would be a good reference for the development of 3D capacitors and other microelectronics components. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

17 pages, 4597 KiB  
Article
Cobalt Ion-Modified Titanium Oxide Nanorods: A Promising Approach for High-Performance Electrochromic Application
by Pritam J. Morankar, Rutuja U. Amate, Aviraj M. Teli, Sonali A. Beknalkar and Chan-Wook Jeon
Coatings 2024, 14(6), 707; https://doi.org/10.3390/coatings14060707 - 4 Jun 2024
Viewed by 974
Abstract
The development of novel cathodic materials with tailored nanostructures is crucial for the advancement of electrochromic devices. In this study, we synthesized cobalt-doped titanium dioxide (Ti-Co) thin films using a facile hydrothermal method to investigate the effects of cobalt doping on their structural, [...] Read more.
The development of novel cathodic materials with tailored nanostructures is crucial for the advancement of electrochromic devices. In this study, we synthesized cobalt-doped titanium dioxide (Ti-Co) thin films using a facile hydrothermal method to investigate the effects of cobalt doping on their structural, morphological, and electrochromic properties. Comprehensive characterization techniques, including X-ray diffraction and Raman analysis, confirmed the highly crystalline nature of the Ti-Co thin films, with specific Raman bands indicating distinct modifications due to cobalt incorporation. The TiO2 nanorods, optimally doped with cobalt (TC-3), demonstrated enhanced charge transport and mobility, significantly improving the electrochromic performance. Among the various compositions studied, the TC-3 sample exhibited superior lithium-ion accommodation, achieving an optical modulation of 73.6% and a high coloration efficiency of 81.50 cm2/C. It also demonstrated excellent electrochromic stability, maintaining performance for up to 5000 s of coloring/bleaching cycles. These results confirm the beneficial impact of cobalt doping on the structural and functional properties of the host material. Furthermore, the practical effectiveness of the TC-3 thin film was validated through the fabrication of an electrochromic device, which showed efficient coloration and bleaching capabilities. This comprehensive research enhances the understanding and functionality of Ti-Co nanorod architectures, highlighting their promising potential for advanced electrochromic applications. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

17 pages, 13344 KiB  
Article
Effect of Polytetrafluoroethylene Coating on Corrosion Wear Properties of AZ31 Magnesium Alloy by Electrophoretic Deposition
by Jilun Zhang, Chaoyi Chen, Junqi Li and Li Chen
Coatings 2024, 14(6), 664; https://doi.org/10.3390/coatings14060664 - 24 May 2024
Cited by 1 | Viewed by 645
Abstract
In this study, we aim to enhance the corrosion and wear resistance of AZ31 magnesium alloy using electrophoretic deposition (EPD) technology to apply a hydrophobic polytetrafluoroethylene (PTFE) coating. Polyethyleneimine (PEI) serves as a charged dispersant, facilitating uniform deposition of PTFE particles on the [...] Read more.
In this study, we aim to enhance the corrosion and wear resistance of AZ31 magnesium alloy using electrophoretic deposition (EPD) technology to apply a hydrophobic polytetrafluoroethylene (PTFE) coating. Polyethyleneimine (PEI) serves as a charged dispersant, facilitating uniform deposition of PTFE particles on the alloy surface. Results demonstrate a significant reduction in corrosion current density (from 67.5 μA/cm2 to 5.2 μA/cm2) and improved wear resistance (wear volume decreased from 0.24167 mm3 to 0.00167 mm3) in a 3.5 wt% NaCl solution compared to uncoated alloy. Moreover, the friction coefficient of the coated sample decreases. These findings underscore the potential of nano-PTFE coatings prepared via EPD in enhancing AZ31 magnesium alloy’s corrosion and wear resistance, providing a foundation for future protective coating design and optimization. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

17 pages, 7705 KiB  
Article
Effect of Annealing on Stress, Microstructure, and Interfaces of NiV/B4C Multilayers
by Chenyuan Chang, Zhenbo Wei, Hui Jiang, Hangjian Ni, Wentao Song, Jialian He, Simeng Xiang, Zhanshan Wang, Zhe Zhang and Zhong Zhang
Coatings 2024, 14(4), 513; https://doi.org/10.3390/coatings14040513 - 20 Apr 2024
Cited by 1 | Viewed by 2937
Abstract
The functionality and reliability of nanoscale multilayer devices and components are influenced by changes in stress and microstructure throughout fabrication, processing, and operation. NiV/B4C multilayers with a d-spacing of 3 nm were prepared by magnetron sputtering, and two groups of annealing [...] Read more.
The functionality and reliability of nanoscale multilayer devices and components are influenced by changes in stress and microstructure throughout fabrication, processing, and operation. NiV/B4C multilayers with a d-spacing of 3 nm were prepared by magnetron sputtering, and two groups of annealing experiments were performed. The stress, microstructure, and interface changes in NiV/B4C after annealing were investigated by grazing-incidence X-ray reflectometry (GIXR), grazing-incidence X-ray diffraction (GIXRD), X-ray diffuse scattering, and grazing-incidence small-angle X-ray scattering (GISAXS). The temperature dependence experiments revealed a gradual shift in the multilayer stress from compression to tension during annealing from 70 °C to 340 °C, with the stress approaching near-zero levels between 70 °C and 140 °C. The time-dependent experiments indicated that most of the stress changes occurred within the initial 10 min, which showed that prolonged annealing was unnecessary. Combining the X-ray diffraction and X-ray scattering measurements, it was found that the changes in the thickness, interface roughness, and lateral correlation length, primarily due to crystallization, drove the changes in stress and microstructure. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

21 pages, 4682 KiB  
Article
Electrodeposition of Nanostructured Co–Cu Thin Alloy Films on to Steel Substrate from an Environmentally Friendly Novel Lactate Bath under Different Operating Conditions
by Raiedhah A. Alsaiari, Medhat M. Kamel and Mervate M. Mohamed
Coatings 2024, 14(4), 407; https://doi.org/10.3390/coatings14040407 - 29 Mar 2024
Viewed by 1170
Abstract
A new lactate bath was proposed to deposit Co–Cu thin alloy films in nanostructure form onto a steel cathode. The deposition bath contained CuSO4.5H2O, CoSO4.7H2O, CH3CHOHCOOH, and anhydrous Na2SO4 at [...] Read more.
A new lactate bath was proposed to deposit Co–Cu thin alloy films in nanostructure form onto a steel cathode. The deposition bath contained CuSO4.5H2O, CoSO4.7H2O, CH3CHOHCOOH, and anhydrous Na2SO4 at pH 10. The effects of [Co2+]/[Cu2+] molar ratios, lactate ion concentration, current density (CD), and bath temperature on cathodic polarization, cathodic current efficacy (CCE), composition, and structure of the Co–Cu alloys were investigated. The new bath had a high cathodic current efficiency of 85%, which increased with the applied CD. However, it decreased as the temperature increased. The produced coatings have an atomic percentage of Cu ranging from 19.8 to 99%. The deposition of the Co–Cu alloy belonged to regular codeposition. The Co content of the deposit increased with the amount of Co2+ ions in the bath, lactate concentration, and current density but decreased as the temperature increased. Cobalt hexagonal close-packed (HCP) and copper-rich, face-centered cubic (FCC) Co–Cu phases combine to form the polycrystalline structure of the electrodeposited Co–Cu alloy. The average crystallite size ranges between 46 and 89 nm. An energy dispersive X-ray (EDX) examination confirmed that the deposit contained Cu and Co metals. The throwing power and throwing index of the alkaline lactate bath were evaluated and found to be satisfactory. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

10 pages, 6005 KiB  
Article
Feasible Parameters of Ohmic Areas of YBaCuO Thin Films Switched via Moving Unstable Border between Superconducting and Normal States
by Linas Ardaravičius and Oleg Kiprijanovič
Coatings 2024, 14(3), 266; https://doi.org/10.3390/coatings14030266 - 22 Feb 2024
Viewed by 972
Abstract
A system of two equations based on one of the classical electricity laws was used to determine the sizes and temperatures of ohmic areas formed under action of overcritical nanosecond electrical pulses. Calculations were performed at five points for three experimentally obtained voltage–current [...] Read more.
A system of two equations based on one of the classical electricity laws was used to determine the sizes and temperatures of ohmic areas formed under action of overcritical nanosecond electrical pulses. Calculations were performed at five points for three experimentally obtained voltage–current (V-I) dependences for samples with the same geometry but different critical current density values. The system included two additional conditions to satisfy the known descriptive model of transition from superconducting (SC) to a normal (N) state—S-N switching—and to obtain physically acceptable solutions over the entire current range of V-I dependence. The solution for each point takes the form of a function, since the initial temperature increase of the primary channel across the film is entered as a parameter. Two modes of concentrated energy release in the channel were disclosed. Their random appearance leads to an unexpected degradation of the sample. As such, the obtained results correspond to the situations occurring during the experiments. The validity of applying additional conditions to the system is discussed. In the discussion, it is also explained at which moments the moving S-N border acquires the velocity of the order of ~106 m/s, comparable to the Fermi velocity. Consideration to describe the moving unstable S-N border as being constantly in a state of Richtmyer–Meshkov instability is presented. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

10 pages, 1932 KiB  
Article
Dependence of Nucleation Field on the Size of Soft Phase in Magnetic Hard–Soft Exchange Coupling Nanocomposites
by Fang Wang, Guoqi Hu, Pengna Zhang, Tangfu Feng, Yajuan Wang, Renbing Sun and Jian Zhang
Coatings 2024, 14(2), 219; https://doi.org/10.3390/coatings14020219 - 10 Feb 2024
Viewed by 1075
Abstract
Hard–soft exchange coupling nanocomposites have critical applications in various important materials. The magnetic properties of nanocomposite permanent magnetic films improve with a higher nucleation field (Hns) of the soft magnetic phase. Hns is sensitive to the thickness (ds) [...] Read more.
Hard–soft exchange coupling nanocomposites have critical applications in various important materials. The magnetic properties of nanocomposite permanent magnetic films improve with a higher nucleation field (Hns) of the soft magnetic phase. Hns is sensitive to the thickness (ds) of the soft magnetic layer. Understanding the dependence of Hns and irreversible field (Hirr) on ds, especially at the nanometric scale, is crucial for comprehending the magnetic mechanism and facilitating the design and preparation of high-performance nanocomposite permanent magnets. However, during the high-temperature deposition process, diffusion between hard and soft magnetic phases occurs, leading to the generation of other phases. This makes it challenging to accurately reflect the relationship between Hns and ds. To address this issue, we successfully fabricated high-quality SmCo5/Fe nanocomposite bilayer films with different soft magnetic thicknesses and high textures by controlling the preparation process. We conducted a quantitative analysis of the relationship between Hns and ds within the range of 2–40 nm. Based on the experimental results, we propose a new theoretical simulation formula that enhances the understanding of the characteristics at the interface between the soft magnetic and hard magnetic phases. The theoretical simulation results show that a thin softened hard layer of about 4–6 nm thickness exists at the interfacial region, which concurrently reverses with the soft magnetic phase during the demagnetization process. Our results offer the generality and critical basis for the further study of hard–soft nanocomposite magnetic materials. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

17 pages, 916 KiB  
Article
Temperature Coefficient of Electronic Polarizability in Thin Polymer Films Deposited on Si and SiO2 Substrates Determined via Spectroscopic Ellipsometry
by Henryk Bednarski, Barbara Hajduk, Paweł Jarka and Pallavi Kumari
Coatings 2024, 14(2), 166; https://doi.org/10.3390/coatings14020166 - 27 Jan 2024
Cited by 2 | Viewed by 1374
Abstract
Ellipsometry is widely used to determine the thermo-optical properties of thin polymer films. However, if the thermo-optic coefficient (TOC) and the linear thermal expansion coefficient (LTEC) are to be used to determine the temperature coefficient of electronic polarizability (TCEP) in thin polymer films, [...] Read more.
Ellipsometry is widely used to determine the thermo-optical properties of thin polymer films. However, if the thermo-optic coefficient (TOC) and the linear thermal expansion coefficient (LTEC) are to be used to determine the temperature coefficient of electronic polarizability (TCEP) in thin polymer films, their values must be determined with the greatest possible accuracy, as both have the opposite effect. In this article, we analyze changes in ellipsometric parameters resulting from changes in the thin film temperature in order to develop a data analysis method for temperature-dependent spectroscopic ellipsometry that will facilitate the accurate determination of thermo-optical parameters, including the TCEP, in polymer thin films. As practical application examples, we identified optimal spectral windows to accurately determine the thermo-optical parameters of 50 to 150 nm-thick PMMA thin films deposited on Si and SiO2 substrates. The influence of thin-film thickness on the accuracy of TOC and LTEC determination is discussed. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

13 pages, 6007 KiB  
Article
Improvement of the Electrocatalytic Properties for the Methanol Oxidation Reaction (MOR) of the CoPt Alloy
by Oana-Georgiana Dragos-Pinzaru, Luiza Racila, Gabriela Buema, Ibro Tabakovic and Nicoleta Lupu
Coatings 2024, 14(1), 17; https://doi.org/10.3390/coatings14010017 - 23 Dec 2023
Cited by 1 | Viewed by 1495
Abstract
The commercialization of the Direct Methanol Fuel Cell (DMFC) is limited due to the high cost and low efficiency of the electrocatalysts. In this context, the development of new electrocatalysts able to efficiently oxidize the methanol and to have at the same time [...] Read more.
The commercialization of the Direct Methanol Fuel Cell (DMFC) is limited due to the high cost and low efficiency of the electrocatalysts. In this context, the development of new electrocatalysts able to efficiently oxidize the methanol and to have at the same time low price and high stability is one of the researcher’s milestones. In this work, CoPt alloys with different Pt content were prepared, and the efficiency of the alloys to be used as electrocatalysts for the methanol oxidation reaction (MOR) was investigated. Our data show that the electrocatalytic performance of the CoPt electrodeposited alloys is strongly influenced by the synthesis conditions, mainly by the potential applied during the synthesis. The best electrocatalytic activity was obtained for the samples prepared at −0.8 V/SCE. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

15 pages, 2975 KiB  
Article
High-Performance Polyimide Films Derived from Biomass-Based Furfural: Fabrication and Properties
by Lei Chen, Weiyu Luo, Yima He, Lizhen Huang, Jinjie Xu, Kaixin Li and Yonggang Min
Coatings 2023, 13(10), 1726; https://doi.org/10.3390/coatings13101726 - 3 Oct 2023
Viewed by 1420
Abstract
The development of renewable polymers as alternatives to the petroleum-based ones has received significant attention due to the increasing depletion of fossil oil and the associated environmental concerns. In this study, a semi-biomass-based polyimide (PI) film was successfully synthesized, using biomass-derived furfural (HMFA) [...] Read more.
The development of renewable polymers as alternatives to the petroleum-based ones has received significant attention due to the increasing depletion of fossil oil and the associated environmental concerns. In this study, a semi-biomass-based polyimide (PI) film was successfully synthesized, using biomass-derived furfural (HMFA) as one of the raw materials. A two-step approach was first developed for this process: (1) conversion of HMFA to 3,3,4,4-biphenyltetracarboxylic acid dianhydride (BPDA) and (2) polymerization of BPDA with p-phenylenediamine (PPD) to form a PI film. The fabricated PI film demonstrated excellent properties, such as a high thermal decomposition temperature up to 600 °C, a satisfactory glass transition temperature (Tg) exceeding 365 °C, a coefficient of thermal expansion (CTE) of ≈30 ppm/K, a tensile strength greater than 120 MPa, a dielectric constant value below 3.4, a dielectric loss value of less than 0.02, and a 24 h water absorption rate below 0.8%. These performances are comparable to the petrochemical-based PI. This work offers a promising strategy for utilizing biomass-derived materials in polyimide synthesis and would drive a new wave of advancements in polymer science. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

10 pages, 2845 KiB  
Article
Paramagnetic Properties of Carbon Films
by Bagila A. Baitimbetova, Yuri A. Ryabikin, Bagdat A. Rakymetov, Danatbek O. Murzalinov, Dinara O. Kantarbaeva, Bahat Duamet, Elena A. Dmitriyeva, Abay S. Serikkanov and Kassym Yelemessov
Coatings 2023, 13(9), 1484; https://doi.org/10.3390/coatings13091484 - 22 Aug 2023
Cited by 1 | Viewed by 1108
Abstract
This research paper presents the results of obtaining carbon films on various substrates (quartz, mica, and silicon) at temperatures from 0 °C (initial) to 800 °C through plasma chemical vapor deposition. The carbon films obtained on various films were studied using the method [...] Read more.
This research paper presents the results of obtaining carbon films on various substrates (quartz, mica, and silicon) at temperatures from 0 °C (initial) to 800 °C through plasma chemical vapor deposition. The carbon films obtained on various films were studied using the method of electron paramagnetic resonance (EPR). EPR measurements were carried out on twenty samples at a perpendicular and parallel arrangement of the sample plane concerning the orientation of the magnetic field. When measuring the resonance conditions by changing the magnetic field, an EPR signal appeared in all of the deposited samples. The paper presents a general view of the EPR spectrum in all of the samples, including the signal intensity, g-factor, line widths, and normalized signal intensity of the carbon films on various substrates at temperatures from 0 °C to 800 °C. Studies show that with an increase in temperature, the normalized intensity of the EPR signal line increases during the deposition of a carbon in all deposited substrates (quartz, mica, and silicon) using the method of plasma decomposition of a mixture of methane and hydrogen. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

11 pages, 2587 KiB  
Article
Fabrication and Characterization of Mineral Hydrophilic Antifogging Film via Vacuum Evaporation Method
by Shenyu Wei, Qi Zheng, Lei Wang, Cheng Peng, Xinglan Cui, Xiaokui Che, Wuyu Wang and Zeen Yu
Coatings 2023, 13(4), 730; https://doi.org/10.3390/coatings13040730 - 3 Apr 2023
Cited by 2 | Viewed by 1730
Abstract
Natural silicate minerals have a wide range of applications as green, non-toxic and low-cost materials. In this paper, hydrophilic anti-fog films of silicate minerals were generated via a vacuum evaporation coating method using natural feldspar minerals as raw material. Thermogravimetric analysis shows that [...] Read more.
Natural silicate minerals have a wide range of applications as green, non-toxic and low-cost materials. In this paper, hydrophilic anti-fog films of silicate minerals were generated via a vacuum evaporation coating method using natural feldspar minerals as raw material. Thermogravimetric analysis shows that the feldspar changes its structure during the coating process, which in turn changes the roughness of the film and improves the hydrophilicity of the film. The hydrophilicity, anti-fogging properties, optical properties and surface morphology of the films were characterized by contact angle measurements, the hydrothermal method, UV-VIS spectrophotometer and atomic force microscopy, respectively. The results show that the mineral films have excellent hydrophilicity. The best anti-fog effect was achieved at a minimum contact angle of 22.3° with water when the thickness of the film was 100 nm. The anti-fog effect gradually decreased with the increasing thickness of the film. The optical transmittance test showed that the film material had a negligible effect on the transmittance of the substrate. When the film thickness was 100 nm, the maximum optical transmittance was 92.2%. This is 4.5% higher than when the film was uncoated, which has a specific visual transmittance effect. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

15 pages, 7623 KiB  
Article
Vapor Deposited Zeolitic Imidazolate Framework-8 Derived from Porous ZnO Thin Films
by Marianne Kräuter, Katrin Unger, Roland Resel and Anna Maria Coclite
Coatings 2023, 13(4), 718; https://doi.org/10.3390/coatings13040718 - 31 Mar 2023
Cited by 4 | Viewed by 1664
Abstract
In recent years, the vapor deposition of zeolitic imidazolate framework-8 (ZIF-8) has gained high attraction due to its good scalability, conformality, and thickness control. The present study provides new fundamental insights regarding the vapor deposition of ZIF-8 from zinc oxide (ZnO). During synthesis, [...] Read more.
In recent years, the vapor deposition of zeolitic imidazolate framework-8 (ZIF-8) has gained high attraction due to its good scalability, conformality, and thickness control. The present study provides new fundamental insights regarding the vapor deposition of ZIF-8 from zinc oxide (ZnO). During synthesis, ZnO thin films with different percentages of open porosity (14.5%–24%) were subjected to a 2-methylimidazole vapor for different conversion times (20 min–24 h). For the first time, the impact of the porosity of ZnO thin films onto the converted ZIF-8 is investigated. Grazing incidence X-ray diffraction reveals randomly oriented crystallites of ZIF-8, which already appear after 20 min of conversion. The thickness, roughness, and average particle height of the ZIF-8 layers increase with the conversion time, reaching values up to (172 ± 20) nm, (29 ± 3) nm, and (113 ± 8) nm, respectively, for ZIF-8 obtained from ZnO with 14.5% open porosity. At long conversion times (i.e., 24 h), the results hint at greater precursor porosities resulting in lower thicknesses of ZIF-8, as the thickness, roughness, and average particle height for ZIF-8 obtained from 24%-porous ZnO show values of (132 ± 20) nm, (25 ± 3) nm and (80 ± 8) nm, respectively. Additionally, the potential of the ZIF-8 layers as a photocatalyst for the degradation of the organic dye methylene blue was studied. The ZIF-8 enhances the degradation by approximately 8% when compared to degradation without a photocatalyst. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

12 pages, 4488 KiB  
Article
Corrosion and Wear Properties of Cr Coating and ZrO2/Cr Bilayer Coating on Zr-4 Alloy
by Xiaolong Pan, Longshi Qiu, Xiaogang Hu and Haixia Jiang
Coatings 2022, 12(9), 1281; https://doi.org/10.3390/coatings12091281 - 1 Sep 2022
Cited by 7 | Viewed by 1975
Abstract
In this study, duplex surface treatments were used to prepare a ZrO2/Cr bilayer coating on zirconium alloy cladding for enhancing the wear and corrosion behaviors. The surface and cross-section morphology of coated Zr-4 alloy was characterized; the results show that the [...] Read more.
In this study, duplex surface treatments were used to prepare a ZrO2/Cr bilayer coating on zirconium alloy cladding for enhancing the wear and corrosion behaviors. The surface and cross-section morphology of coated Zr-4 alloy was characterized; the results show that the Cr- and ZrO2/Cr-coated samples had similar morphology, and more obvious surface undulates could be observed on the ZrO2/Cr coating than the pure Cr coating owing to the rough surface of the plasma electrolytic oxidation coating. Wear and electrochemical behavior in 1200 mg/L H3BO3 and 2.2 mg/L LiOH solutions of original and coated Zr-4 alloy were investigated. The electrochemical corrosion test indicated the coated Zr-4 alloy exhibited better corrosion resistance behavior than the original Zr-4 alloy. The potentiodynamic polarization curves and corrosion morphology suggest the pitting corrosion occurred on the surface of the original and coated Zr-4 alloy. The ZrO2/Cr-coated Zr-4 alloy had better corrosion resistance due to the dual protection of the PEO layer and Cr coating. The wear behavior of the original and coated Zr-4 alloy was also investigated under a constant load of 5 N. The results reveal that the coated Zr-4 alloy had better wear resistance, and the PEO layer was found to significantly enhance the wear resistance of the Zr-4 alloy. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

18 pages, 4247 KiB  
Article
Effect of Modified Tetraethyl Orthosilicate Surface Treatment Agents on the Permeability of Airport Pavement Concrete
by Tianlun Li and Yonggen Wu
Coatings 2022, 12(7), 1027; https://doi.org/10.3390/coatings12071027 - 20 Jul 2022
Cited by 3 | Viewed by 1954
Abstract
In this paper, three modified tetraethyl orthosilicate surface treatment agents were prepared by using tetraethyl orthosilicate (TEOS) as the preparation monomer, isobutyltriethoxysilane (IBTS) as the hybridizer, and acrylic acid, phosphoric acid, and hydrochloric acid as the catalysts. The effects of the three modified [...] Read more.
In this paper, three modified tetraethyl orthosilicate surface treatment agents were prepared by using tetraethyl orthosilicate (TEOS) as the preparation monomer, isobutyltriethoxysilane (IBTS) as the hybridizer, and acrylic acid, phosphoric acid, and hydrochloric acid as the catalysts. The effects of the three modified tetraethyl orthosilicate surface treatment agents on the permeability of airport pavement surface concrete were investigated by water absorption tests, water contact angle tests, water penetration resistance tests, chloride ion penetration resistance tests, and carbonation tests, and the mechanisms of action of the modified tetraethyl orthosilicate surface treatment agents were analyzed by microscopic tests. The results showed that all three tetraethyl orthosilicate surface treatment agents could significantly improve the impermeability of concrete, among which the modified tetraethyl orthosilicate surface treatment agent with hydrochloric acid as the catalyst had the most obvious effect on the improvement of the impermeability of concrete. Acrylic acid was weaker than hydrochloric acid as the catalyst of a modified tetraethyl orthosilicate surface treatment agent for the improvement of concrete impermeability; it was only slightly stronger than hydrochloric acid as the catalyst of modified tetraethyl orthosilicate surface treatment agent in terms of the improvement of concrete’s resistance to water penetration, and the difference between the two was not significant. Phosphoric acid as a catalyst of the modified tetraethyl orthosilicate surface treatment agent was the least effective for concrete impermeability; it was only stronger than the other two modified tetraethyl orthosilicate surface treatment agents in the improvement of concrete resistance to carbonation, and the carbonation depth of the concrete was only 1 mm in 28 days. SEM and MIP tests showed that the modified tetraethyl orthosilicate surface treatment agents improved the impermeability of concrete mainly by producing additional hydrated calcium silicate gel to plug microcracks and pores, reduce the total porosity of the concrete and the number of multi-harmful and harmful pores, and improve the compactness of the concrete. The test results can provide a reference for the development of modified tetraethyl orthosilicate surface treatment agents and their application in airport pavement surface engineering. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

18 pages, 2236 KiB  
Article
Synthesis and Characterization of Boron Thin Films Using Chemical and Physical Vapor Depositions
by Bart Schurink, Wesley T. E. van den Beld, Roald M. Tiggelaar, Robbert W. E. van de Kruijs and Fred Bijkerk
Coatings 2022, 12(5), 685; https://doi.org/10.3390/coatings12050685 - 16 May 2022
Cited by 4 | Viewed by 3665
Abstract
Boron as thin film material is of relevance for use in modern micro- and nano-fabrication technology. In this research boron thin films are realized by a number of physical and chemical deposition methods, including magnetron sputtering, electron-beam evaporation, plasma enhanced chemical vapor deposition [...] Read more.
Boron as thin film material is of relevance for use in modern micro- and nano-fabrication technology. In this research boron thin films are realized by a number of physical and chemical deposition methods, including magnetron sputtering, electron-beam evaporation, plasma enhanced chemical vapor deposition (CVD), thermal/non-plasma CVD, remote plasma CVD and atmospheric pressure CVD. Various physical, mechanical and chemical characteristics of these boron thin films are investigated, i.e., deposition rate, uniformity, roughness, stress, composition, defectivity and chemical resistance. Boron films realized by plasma enhanced chemical vapor deposition (PECVD) are found to be inert for conventional wet chemical etchants and have the lowest amount of defects, which makes this the best candidate to be integrated into the micro-fabrication processes. By varying the deposition parameters in the PECVD process, the influences of plasma power, pressure and precursor inflow on the deposition rate and intrinsic stress are further explored. Utilization of PECVD boron films as hard mask for wet etching is demonstrated by means of patterning followed by selective structuring of the silicon substrate, which shows that PECVD boron thin films can be successfully applied for micro-fabrication. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

8 pages, 2393 KiB  
Article
Enhanced Properties of Micro Arc Oxidation Coating with Cu Addition on TC4 Alloy in Marine Environment
by Wei Gao, Jiangnan Liu, Jingpeng Wei, Yuhong Yao, Xiqun Ma and Wei Yang
Coatings 2021, 11(10), 1168; https://doi.org/10.3390/coatings11101168 - 27 Sep 2021
Cited by 5 | Viewed by 2015
Abstract
By contrast with the traditional method of adding hard particles into micro arc oxidation (MAO) coating to improve its wear performance, this study introduced copper into the MAO coating on TC4 alloy by adding copper pyrophosphate to enhance the wear property in a [...] Read more.
By contrast with the traditional method of adding hard particles into micro arc oxidation (MAO) coating to improve its wear performance, this study introduced copper into the MAO coating on TC4 alloy by adding copper pyrophosphate to enhance the wear property in a marine environment and the antibacterial property. The results demonstrated that the MAO coating with copper pyrophosphate addition showed a porous structure, and Cu was mainly concentrated around micropores. CuO and Cu2O were formed in this MAO coating. This MAO coating with Cu had a high bonding strength to the substrate. Although the hardness of the coating with Cu had been reduced, it could reduce the friction coefficient and enhance the wear property in simulated seawater due to the lubrication of Cu. Furthermore, this MAO coating with Cu addition had obvious antibacterial and bactericidal effects due to the antibacterial effect of Cu. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

12 pages, 18906 KiB  
Article
Moisture-Assisted Formation of High-Quality Silver Nanowire Transparent Conductive Films with Low Junction Resistance
by Lipeng Zhou, Yuehui Hu, Hao Gao, Youliang Gao, Wenjun Zhu, Lilin Zhan, Huiwen Liu, Yichuan Chen, Keyan Hu, Pengfei Wang, Di Wang, Fang Hu, Ke Zhou, Wei Liu and Ning Chang
Coatings 2021, 11(6), 671; https://doi.org/10.3390/coatings11060671 - 1 Jun 2021
Cited by 8 | Viewed by 3178
Abstract
Silver nanowire (AgNWs) transparent conductive film (TCF) is considered to be the most favorable material to replace indium tin oxide (ITO) as the next-generation transparent conductive film. However, the disadvantages of AgNWs, such as easy oxidation and high wire-wire junction resistance, dramatically limit [...] Read more.
Silver nanowire (AgNWs) transparent conductive film (TCF) is considered to be the most favorable material to replace indium tin oxide (ITO) as the next-generation transparent conductive film. However, the disadvantages of AgNWs, such as easy oxidation and high wire-wire junction resistance, dramatically limit its commercial application. In this paper, moisture treatment was adopted, and water was dripped on the surface of AgNWs film or breathed on the surface so that the surface was covered with a layer of water vapor. The morphology of silver nanowire mesh nodes is complex, and the curvature is large. According to the capillary condensation theory, water molecules preferentially condense near the geometric surface with significant curvature. The capillary force is generated, making the wire-wire junction of AgNWs mesh bond tightly, resulting in good ohmic contact. The experimental results show that AgNWs-TCF treated by moisture has better conductivity, with an average sheet resistance of 20 Ω/sq and more uniform electrical properties. The bending test and adhesion test showed that AgNWs-TCF treated by moisture still exhibited good mechanical bending resistance and environmental stability. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

12 pages, 6080 KiB  
Article
Two-Step Deposition of Silicon Oxide Films Using the Gas Phase Generation of Nanoparticles in the Chemical Vapor Deposition Process
by Jae-Ho Suk, Sung-Chun Hong, Gil-Su Jang and Nong-Moon Hwang
Coatings 2021, 11(3), 365; https://doi.org/10.3390/coatings11030365 - 23 Mar 2021
Cited by 2 | Viewed by 2552
Abstract
Non-classical crystallization, in which charged nanoparticles (NPs) are the building blocks of film growth, has been extensively studied in chemical vapor deposition (CVD). Here, the deposition behavior of silicon oxide films by the two-step growth process, where NPs are generated in the gas [...] Read more.
Non-classical crystallization, in which charged nanoparticles (NPs) are the building blocks of film growth, has been extensively studied in chemical vapor deposition (CVD). Here, the deposition behavior of silicon oxide films by the two-step growth process, where NPs are generated in the gas phase at high temperature and deposited as films at low temperature, was studied in the CVD process. Although we supplied SiH4, H2, and N2, the deposited film turned out to be silicon oxide, which is attributed to relatively poor vacuum. Also, silicon oxide NPs were captured on transmission electron microscopy (TEM) carbon membranes of a copper grid for 10 s under various conditions. When the quartz tube with a conical nozzle was used, the size of nanoparticles increased drastically with increasing processing time (or delay time) and porous films with a rough surface were deposited. When the quartz tube without a nozzle was used, however, the size did not increase much with increasing processing time and dense films with a smooth surface were deposited. These results suggest that the size of nanoparticles is an important parameter for the deposition of dense films for two-step growth at low temperatures. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

18 pages, 21009 KiB  
Article
Synthesis and Characterization of Nanostructured Polyaniline Thin Films with Superhydrophobic Properties
by Zeinab Abdel Hamid, Mona Hasan Gomaa, Sayed S. Abdel Rehim, Maamoun Abdel Hamid and Ahmed Ibrahim
Coatings 2019, 9(11), 748; https://doi.org/10.3390/coatings9110748 - 11 Nov 2019
Cited by 21 | Viewed by 4546
Abstract
Polyaniline (PANI) thin films incorporated with TiO2 or ZnO nanoparticles were synthesized via an electrochemical polymerization technique. Cyclic voltammetry (CV) was used to synthesize PANI from a strongly acidic medium (0.5 M H2SO4). The effects of different deposition [...] Read more.
Polyaniline (PANI) thin films incorporated with TiO2 or ZnO nanoparticles were synthesized via an electrochemical polymerization technique. Cyclic voltammetry (CV) was used to synthesize PANI from a strongly acidic medium (0.5 M H2SO4). The effects of different deposition cycles on the morphology, thickness, color, and properties of electrodeposited PANI thin films nanocomposites were investigated. Furthermore, the effects of the nanoparticles concentration on the morphology and water contact angle (CA) of the produced coating were investigated. Field-emission scanning electron microscopy (FE-SEM) and high-resolution transmission electron microscopy (HR-TEM) were used to investigate the morphological structure. X-ray photoelectron spectroscopy (XPS) was used to study the surface composition of the formed film. The results reveal that the CA of the prepared coating reached 146°. A granular morphology of PANI with a moderate concentration of nanoparticles was obtained. In addition, XPS analysis confirmed the incorporation of the oxide nanoparticles in the matrix. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

6 pages, 3277 KiB  
Article
Fingerprint Blurring on a Hierarchical Nanoporous Layer Glass
by Erika Tabata, Takumi Ito, Yuki Ushioda and Takuya Fujima
Coatings 2019, 9(10), 653; https://doi.org/10.3390/coatings9100653 - 10 Oct 2019
Cited by 5 | Viewed by 2887
Abstract
A fingerprint blurring phenomenon on a hierarchical nanoporous layer (HNL) glass has been discovered and experimentally investigated. The HNL glass was prepared by a simple one-pot etching as reported by the authors. IR absorption spectra and water contact angle revealed that the blurring [...] Read more.
A fingerprint blurring phenomenon on a hierarchical nanoporous layer (HNL) glass has been discovered and experimentally investigated. The HNL glass was prepared by a simple one-pot etching as reported by the authors. IR absorption spectra and water contact angle revealed that the blurring does not come from a chemical decomposition but a transportation of the fingerprint components, and the capillary action drives the transportation, not the thermal diffusion. The fine pores in the HNL was indicated to develop the strong capillary force to blur the fingerprint. The fingerprint blurring phenomenon on the HNL can be a candidate for the third anti-fingerprint methodology after the popular ones of low frictional surfaces and anti-glare surfaces. Full article
(This article belongs to the Special Issue Thin-Film Synthesis, Characterization and Properties)
Show Figures

Figure 1

Back to TopTop