energies-logo

Journal Browser

Journal Browser

Renewable Energy and Energy Storage Systems

A topical collection in Energies (ISSN 1996-1073). This collection belongs to the section "B: Energy and Environment".

Viewed by 232429

Editors


grade E-Mail Website
Collection Editor
1. Department of Sustainable and Renewable Energy Engineering, University of Sharjah, Sharjah P.O. Box 27272, United Arab Emirates
2. Mechanical Engineering and Design, School of Engineering and Applied Science, Aston University, Aston Triangle, Birmingham B4 7ET, UK
Interests: renewable energy; energy storage systems, sustainability; CAD and design; smart materials
Special Issues, Collections and Topics in MDPI journals

E-Mail Website
Collection Editor
Department of Mechanics, Mathematics & Management, Polytechnical University of Bari, Piazza Umberto I, 1, 70121 Bari BA, Italy
Interests: manufacturing processes; product lifecycle management; sustainable manufacturing; eco-sustainability; industrial and manufacturing engineering; continuous improvement of manufacturing processes; distributed and delocalized production systems; quality management; renewable sources; manufacturing execution systems; cyber-physical systems; smart materials and their manufacturing and applications
Special Issues, Collections and Topics in MDPI journals
William G. Lowrie Department of Chemical and Biomolecular Engineering, The Ohio State University, Columbus, OH 43210, USA
Interests: carbon capture utilization and storage (CCUS); gas separation; membrane; polymer; absorption; process modeling; mass transfer; heat transfer; fossil fuel; renewable energy; hydrate; wastewater treatment
Special Issues, Collections and Topics in MDPI journals

Topical Collection Information

Dear Colleagues,

This Special Issue covers the state of the art of the following renewable energy and energy storage systems topics: solar energy, wind energy, biomass and bioenergy, hydro power, tidal and wave energy, geothermal energy, mechanical energy storage systems, electrochemical storage systems, thermal storage systems, air-compressed storage systems, and all related fields.

Prof. Dr. Abdul-Ghani Olabi
Prof. Ing. Michele Dassisti
Dr. Zhien Zhang
Collection Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the collection website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Energies is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Published Papers (90 papers)

2024

Jump to: 2023, 2022, 2021, 2020

18 pages, 561 KiB  
Article
On-Farm Production of Renewable Energy in 2014–2022
by Roma Ryś-Jurek
Energies 2024, 17(21), 5395; https://doi.org/10.3390/en17215395 - 30 Oct 2024
Viewed by 207
Abstract
The main purpose of this study is to present family farms as consumers and producers of renewable energies which provide them with an opportunity to reduce operating costs. The time scope of the study is 2014–2022, and the Farm Accountancy Data Network is [...] Read more.
The main purpose of this study is to present family farms as consumers and producers of renewable energies which provide them with an opportunity to reduce operating costs. The time scope of the study is 2014–2022, and the Farm Accountancy Data Network is used as the data source. The following research methods were employed: comparative and descriptive analysis, intensity indicators, ranking assignment and panel regression. Based on the values of energy output and energy costs, the rankings revealed a strong position of the Netherlands and Germany. As demonstrated by the study, energy production and consumption volumes depend on the farms’ economic size, but are not impacted by production type. Another finding is that energy production covers only one-third of its costs. Also, both production volumes and costs were on a growth path on a year-over-year basis, with similar growth ratios. The European Union’s leaders in energy consumption and production are the Netherlands, Germany, Belgium, Denmark, Czech Republic, Hungary, Luxembourg, Slovakia and Sweden. The study included the structuring of panel models for energy output and costs and identified their determinants. Energy output depends on total inputs and grows as they grow. Energy costs, in turn, are related to utilized agricultural area, total output and family farm income. An important limitation of this study is that FADN is a provider of high-level data. Hence, it is impossible to tell what specific sources of renewable energy are used by farms, and how they are affected by such exogenous factors as climate, earmarked subsidies or energy policy. The findings from this study are discussed in the context of the European Commission’s recommendations laid down in the Bioeconomy Strategy of the EU (2013), the Seventh Environment Action Program, the New Innovation Agenda of the European Union, the Report “Transforming Our World: the United Nations 2030 Agenda for Sustainable Development” and the Circular Economy Action Plan. Full article
Show Figures

Figure 1

1 pages, 133 KiB  
Correction
Correction: Ebner et al. Photovoltaic Roofing for Motorways and Other High-Ranking Road Networks: Technical Feasibility, Yield Estimation, and Final Demonstrator. Energies 2024, 17, 3991
by Rita Ebner, Christoph Mayr, Marcus Rennhofer, Karl A. Berger, Martin Heinrich, Felix Basler, Andreas J. Beinert, Jonas D. Huyeng, Manfred Haider, Dominik Prammer, Alois Vorwagner, Markus Fehringer and Tobias Beck
Energies 2024, 17(19), 4999; https://doi.org/10.3390/en17194999 - 8 Oct 2024
Viewed by 306
Abstract
In the published publication [...] Full article
65 pages, 7172 KiB  
Article
Evaluation of the Suitability of Geodetic Databases to Support the Process of Locating Renewable Energy Investments
by Teresa Front-Dąbrowska and Anita Kwartnik-Pruc
Energies 2024, 17(19), 4919; https://doi.org/10.3390/en17194919 - 1 Oct 2024
Viewed by 426
Abstract
Enhancing the production of energy from renewable energy sources (RES) has been a consistently important issue for many years, both in Poland and other countries around the world. Selecting sites for devices that convert renewable energy into electricity requires various spatial data, especially [...] Read more.
Enhancing the production of energy from renewable energy sources (RES) has been a consistently important issue for many years, both in Poland and other countries around the world. Selecting sites for devices that convert renewable energy into electricity requires various spatial data, especially during the initial design stage when optimal investment locations are identified. The article presents a new method for assessing the usefulness of publicly accessible Polish geodetic databases—the Topographic Objects Database (Polish name: BDOT10k) and the Digital Elevation Model (DEM, Polish name: NMT)–in the process of renewable energy infrastructure siting. This study is the first to jointly assess these two databases from the user’s perspective rather than the creator’s or administrator’s viewpoint. User requirements for spatial data were defined through research factors identified in a literature review. The methodology developed includes checking the availability of Polish geodetic databases and evaluating the quality of spatial data. Analyses were performed in a GIS environment for eighteen research areas in Poland. A suitability coefficient was developed to determine the usefulness of the databases studied. The obtained value of the suitability coefficient in each area was above 50% of its maximum value, which was taken as a threshold value proving the suitability of the analyzed databases for the purpose specified in the study. The databases are fully useful for a group of province and poviat capital cities—there the suitability coefficient value exceeds 80% of its maximum value. The studies confirmed the validity of using publicly accessible BDOT10k and DEM geodetic databases in GIS analyses for the search for sites for solar, wind, and small hydroelectric power plants. Full article
Show Figures

Figure 1

29 pages, 5589 KiB  
Review
An Overview of Silica Scaling Reduction Technologies in the Geothermal Market
by Rochelle Longval, Rauan Meirbekova, Jason Fisher and Audrey Maignot
Energies 2024, 17(19), 4825; https://doi.org/10.3390/en17194825 - 26 Sep 2024
Viewed by 1627
Abstract
Renewable energy sources play a vital role in the energy mix with geothermal energy providing an opportunity to harness the natural heat coming from the Earth for sustainable power production. As innovative drilling technologies come to market, it is easier to extract heat [...] Read more.
Renewable energy sources play a vital role in the energy mix with geothermal energy providing an opportunity to harness the natural heat coming from the Earth for sustainable power production. As innovative drilling technologies come to market, it is easier to extract heat from various localities across the globe, leading to significant development in the geothermal sector. The economic viability of this resource can be significantly impacted when energy output declines due to scale deposition. Scale formation is a major challenge in the exploitation of geothermal wells, particularly in liquid-dominated geothermal fields. One of the most robust forms of scale build-up common to higher temperature geothermal wellbores and surface equipment for power production is silica scaling. Silica is one of the Earth’s most abundant elements that can precipitate from brine due to various factors. The accumulation of scale deposits significantly impacts the lifespan and efficiency of surface equipment and geothermal wells by restricting fluid flow, thus reducing efficiency and performance. To guarantee the peak performance and longevity of geothermal systems, it is essential to implement a strategic maintenance plan for scaling reduction in geothermal systems. Throughout this review, relevant case studies highlight scaling reduction methods for silica scale in subsurface wellbores and surface facilities. Full article
Show Figures

Figure 1

27 pages, 4294 KiB  
Communication
Opportunities and Challenges of Geothermal Energy: A Comparative Analysis of Three European Cases—Belgium, Iceland, and Italy
by Rauan Meirbekova, Dario Bonciani, Dagur Ingi Olafsson, Aysun Korucan, Pinar Derin-Güre, Virginie Harcouët-Menou and Wilfried Bero
Energies 2024, 17(16), 4134; https://doi.org/10.3390/en17164134 - 20 Aug 2024
Viewed by 1914
Abstract
Geothermal energy is a unique energy source in the energy policy mix that would help the clean energy transition and energy independence, supporting the energy needs in heating and electricity. Although there have been studies on the opportunities and challenges of renewable energy, [...] Read more.
Geothermal energy is a unique energy source in the energy policy mix that would help the clean energy transition and energy independence, supporting the energy needs in heating and electricity. Although there have been studies on the opportunities and challenges of renewable energy, this paper is the first paper that concentrates on geothermal energy for three distinct countries, Italy, Belgium, and Iceland, for the first time. Using semi-structured interviews that will cover the stakeholders representing the quadruple helix (academia, citizens, policymakers, and industry), this paper aims to find the unique and common opportunities and barriers the geothermal sector has. Shared challenges include financial barriers, regulatory complexities, environmental issues, and the need for improvement in the social acceptability of geothermal energy. Despite these challenges, geothermal energy, a promising energy source for clean transition, could create opportunities like improved household welfare through combined uses in district heating and electricity and have the potential to generate employment opportunities. Full article
Show Figures

Figure 1

17 pages, 11385 KiB  
Article
Photovoltaic Roofing for Motorways and Other High-Ranking Road Networks: Technical Feasibility, Yield Estimation, and Final Demonstrator
by Rita Ebner, Christoph Mayr, Marcus Rennhofer, Karl A. Berger, Martin Heinrich, Felix Basler, Andreas J. Beinert, Jonas D. Huyeng, Manfred Haider, Dominik Prammer, Alois Vorwagner, Markus Fehringer and Tobias Beck
Energies 2024, 17(16), 3991; https://doi.org/10.3390/en17163991 - 12 Aug 2024
Cited by 1 | Viewed by 813 | Correction
Abstract
As renewable energies need to be extended massively, new concepts are necessary to prevent land conflicts with other uses. Such concepts should have a high generality to offer a swift expansion of renewables anywhere. Within the project, the Photovoltaic Road Roofing Concept (PV-SÜD), [...] Read more.
As renewable energies need to be extended massively, new concepts are necessary to prevent land conflicts with other uses. Such concepts should have a high generality to offer a swift expansion of renewables anywhere. Within the project, the Photovoltaic Road Roofing Concept (PV-SÜD), a concept for the roofing of roadways with solar panels, was investigated. Its effects on the road infrastructure were analyzed, and a demonstrator was built. The technical boundary conditions and requirements resulting from the specific application type were determined regarding the photovoltaic technology, the possible energy generation, and the supporting structure. The study was completed for a technical solution of 10 m length, 17 m width, and 6.8 m height, with the option of a pent roof (highways running east–west) or gable roofs (highways running north–south). The main target aim was to investigate the potential for widespread use at any site, in contrast to previous studies which mainly aimed at a singular site or demonstrator project. The final solution can support a 38.5 kWp photovoltaic system with a specific annual yield of between 37.5 MWh and 44.0 MWh. The yield variation in sites in Austria and Germany was 14.7% and 17.9%, respectively. One demonstrator roofing was realized as a steel-frame construction with active glass–glass photovoltaic technology at a highway in Hegau (GE). Full article
Show Figures

Figure 1

19 pages, 12030 KiB  
Article
Optimization of the Performance of PCM Thermal Storage Systems
by Giampietro Fabbri, Matteo Greppi and Federico Amati
Energies 2024, 17(13), 3343; https://doi.org/10.3390/en17133343 - 8 Jul 2024
Viewed by 702
Abstract
In this article, we present some optimised geometries for a thermal storage system previously proposed exploiting Phase-changing materials (PCMs). The optimization has been carried out by using a genetic algorithm. We demonstrate that a simple single-parental, mutation-based, single-objective genetic algorithm can be conveniently [...] Read more.
In this article, we present some optimised geometries for a thermal storage system previously proposed exploiting Phase-changing materials (PCMs). The optimization has been carried out by using a genetic algorithm. We demonstrate that a simple single-parental, mutation-based, single-objective genetic algorithm can be conveniently employed to optimize the geometry of the proposed PCM thermal energy storage system. Optimization I was the one with the least restrictive conditions and, therefore, with the greatest possibility of variation in the channel geometry. While the one with the worst results is Optimization II because of the most restrictive conditions, primarily constant solid/liquid volume. A metal frame increases the surface area by 6. Full article
Show Figures

Figure 1

19 pages, 1120 KiB  
Article
Long Short-Term Renewable Energy Sources Prediction for Grid-Management Systems Based on Stacking Ensemble Model
by Wiem Fekih Hassen and Maher Challouf
Energies 2024, 17(13), 3145; https://doi.org/10.3390/en17133145 - 26 Jun 2024
Viewed by 956
Abstract
The transition towards sustainable energy systems necessitates effective management of renewable energy sources alongside conventional grid infrastructure. This paper presents a comprehensive approach to optimizing grid management by integrating Photovoltaic (PV), wind, and grid energies to minimize costs and enhance sustainability. A key [...] Read more.
The transition towards sustainable energy systems necessitates effective management of renewable energy sources alongside conventional grid infrastructure. This paper presents a comprehensive approach to optimizing grid management by integrating Photovoltaic (PV), wind, and grid energies to minimize costs and enhance sustainability. A key focus lies in developing an accurate scheduling algorithm utilizing Mixed Integer Programming (MIP), enabling dynamic allocation of energy resources to meet demand while minimizing reliance on cost-intensive grid energy. An ensemble learning technique, specifically a stacking algorithm, is employed to construct a robust forecasting pipeline for PV and wind energy generation. The forecasting model achieves remarkable accuracy with a Root Mean Squared Error (RMSE) of less than 0.1 for short-term (15 min and one day ahead) and long-term (one week and one month ahead) predictions. By combining optimization and forecasting methodologies, this research contributes to advancing grid management systems capable of harnessing renewable energy sources efficiently, thus facilitating cost savings and fostering sustainability in the energy sector. Full article
Show Figures

Figure 1

27 pages, 3809 KiB  
Review
A Review of Coupled Geochemical–Geomechanical Impacts in Subsurface CO2, H2, and Air Storage Systems
by Zhuofan Shi, Dejene L. Driba, Nora Lopez Rivera, Mohammad Kariminasab and Lauren E. Beckingham
Energies 2024, 17(12), 2928; https://doi.org/10.3390/en17122928 - 14 Jun 2024
Cited by 2 | Viewed by 1253
Abstract
Increased demand for decarbonization and renewable energy has led to increasing interest in engineered subsurface storage systems for large-scale carbon reduction and energy storage. In these applications, a working fluid (CO2, H2, air, etc.) is injected into a deep [...] Read more.
Increased demand for decarbonization and renewable energy has led to increasing interest in engineered subsurface storage systems for large-scale carbon reduction and energy storage. In these applications, a working fluid (CO2, H2, air, etc.) is injected into a deep formation for permanent sequestration or seasonal energy storage. The heterogeneous nature of the porous formation and the fluid–rock interactions introduce complexity and uncertainty in the fate of the injected component and host formations in these applications. Interactions between the working gas, native brine, and formation mineralogy must be adequately assessed to evaluate the efficiency, risk, and viability of a particular storage site and operational regime. This study reviews the current state of knowledge about coupled geochemical–geomechanical impacts in geologic carbon sequestration (GCS), underground hydrogen storage (UHS), and compressed air energy storage (CAES) systems involving the injection of CO2, H2, and air. Specific review topics include (1) existing injection induced geochemical reactions in these systems; (2) the impact of these reactions on the porosity and permeability of host formation; (3) the impact of these reactions on the mechanical properties of host formation; and (4) the investigation of geochemical-geomechanical process in pilot scale GCS. This study helps to facilitate an understanding of the potential geochemical–geomechanical risks involved in different subsurface energy storage systems and highlights future research needs. Full article
Show Figures

Figure 1

29 pages, 4449 KiB  
Article
Techno-Economic Assessment of Molten Salt-Based Concentrated Solar Power: Case Study of Linear Fresnel Reflector with a Fossil Fuel Backup under Saudi Arabia’s Climate Conditions
by Ahmed Aljudaya, Stavros Michailos, Derek B. Ingham, Kevin J. Hughes, Lin Ma and Mohamed Pourkashanian
Energies 2024, 17(11), 2719; https://doi.org/10.3390/en17112719 - 3 Jun 2024
Viewed by 952
Abstract
Concentrated solar power (CSP) has gained traction for generating electricity at high capacity and meeting base-load energy demands in the energy mix market in a cost-effective manner. The linear Fresnel reflector (LFR) is valued for its cost-effectiveness, reduced capital and operational expenses, and [...] Read more.
Concentrated solar power (CSP) has gained traction for generating electricity at high capacity and meeting base-load energy demands in the energy mix market in a cost-effective manner. The linear Fresnel reflector (LFR) is valued for its cost-effectiveness, reduced capital and operational expenses, and limited land impact compared to alternatives such as the parabolic trough collector (PTC). To this end, the aim of this study is to optimize the operational parameters, such as the solar multiple (SM), thermal energy storage (TES), and fossil fuel (FF) backup system, in LFR power plants using molten salt as a heat transfer fluid (HTF). A 50 MW LFR power plant in Duba, Saudi Arabia, serves as a case study, with a Direct Normal Irradiance (DNI) above 2500 kWh/m2. About 600 SM-TES configurations are analyzed with the aim of minimizing the levelized cost of electricity (LCOE). The analysis shows that a solar-only plant can achieve a low LCOE of 11.92 ¢/kWh with a capacity factor (CF) up to 36%, generating around 131 GWh/y. By utilizing a TES system, the SM of 3.5 and a 15 h duration TES provides the optimum integration by increasing the annual energy generation (AEG) to 337 GWh, lowering the LCOE to 9.24 ¢/kWh, and boosting the CF to 86%. The techno-economic optimization reveals the superiority of the LFR with substantial TES over solar-only systems, exhibiting a 300% increase in annual energy output and a 20% reduction in LCOE. Additionally, employing the FF backup system at 64% of the turbine’s rated capacity boosts AEG by 17%, accompanied by a 5% LCOE reduction. However, this enhancement comes with a trade-off, involving burning a substantial amount of natural gas (503,429 MMBtu), leading to greenhouse gas emissions totaling 14,185 tonnes CO₂ eq. This comprehensive analysis is a first-of-a-kind study and provides insights into the optimal designs of LFR power plants and addresses thermal, economic, and environmental considerations of utilizing molten salt with a large TES system as well as employing natural gas backup. The outcomes of the research address a wide audience including academics, operators, and policy makers. Full article
Show Figures

Figure 1

20 pages, 1244 KiB  
Article
Optimal Operation of Energy Storage Facilities in Incentive-Based Energy Communities
by Giovanni Gino Zanvettor, Marco Casini and Antonio Vicino
Energies 2024, 17(11), 2589; https://doi.org/10.3390/en17112589 - 27 May 2024
Viewed by 821
Abstract
The green energy transition calls for various solutions to enhance environmental sustainability. One of these is represented by renewable energy communities, which may help transition from centralized energy production to distributed renewable generation. European countries are actively promoting incentive schemes for energy communities [...] Read more.
The green energy transition calls for various solutions to enhance environmental sustainability. One of these is represented by renewable energy communities, which may help transition from centralized energy production to distributed renewable generation. European countries are actively promoting incentive schemes for energy communities to foster local electricity self-consumption in order to balance demand and renewable generation. In this context, energy storage facilities can be employed to gather the energy production surplus and use it in periods of low generation. In this paper, we focus on the optimal operation of an incentive-based energy community in the presence of energy storage systems. A centralized optimization problem was formulated to optimally operate storage systems at the community level. Starting from this solution, distributed charging/discharging commands were found to optimally operate the single storage units. Moreover, conditions guaranteeing the convenience of using energy storage systems inside the community were derived. Numerical simulations were performed to validate the reported results and to evaluate the potential benefits of energy storage facilities inside renewable energy communities. Full article
Show Figures

Figure 1

24 pages, 9576 KiB  
Article
Standalone and Hybridised Flywheels for Frequency Response Services: A Techno-Economic Feasibility Study
by Andrew J. Hutchinson and Daniel T. Gladwin
Energies 2024, 17(11), 2577; https://doi.org/10.3390/en17112577 - 26 May 2024
Cited by 1 | Viewed by 817
Abstract
Frequency response services are one of the key components used by major electrical networks worldwide, acting to help control the frequency within set boundaries. Battery Energy Storage Systems (BESSs) are commonly deployed for this purpose; however, their potential is limited by susceptibility to [...] Read more.
Frequency response services are one of the key components used by major electrical networks worldwide, acting to help control the frequency within set boundaries. Battery Energy Storage Systems (BESSs) are commonly deployed for this purpose; however, their potential is limited by susceptibility to cycle-based degradation and widely reported safety incidents. Flywheel Energy Storage Systems (FESSs) do not share these weaknesses and hence could be a potential candidate for longer-term participation in frequency response markets. This study presents the most in-depth and wide-ranging techno-economic analysis of the feasibility of FESSs for frequency response to date. Standalone FESSs are shown to be economically viable across a range of different specifications, achieving a positive Net Present Value (NPV) under varying economic conditions. At a capital cost of 500 GBP/kW with a discount rate of 4%, a 5C FESS can achieve an NPV of GBP 38,586 as a standalone unit. The complex trade-offs when considering hybridising FESSs and BESSs for this application are also investigated in-depth for the first time, again showing positive changes to NPV under various scenarios. Conversely, under some conditions, hybridisation can have a significant negative impact, showcasing the optimisation needed when considering hybrid systems. The impact of introducing a hybrid BESS varies from a low of decreasing the NPV of the system by GBP 97,955 to a high of increasing the NPV by GBP 119,621 depending on the configuration chosen. This comprehensive work provides the foundations for future research into FESS deployment for frequency response services and shows for the first time the circumstances under which deployment for this application would be both technically and economically viable. Full article
Show Figures

Figure 1

20 pages, 1469 KiB  
Review
Exploring the Role of Additives in Enhancing the Performance of Limestone-Based Thermochemical Energy Storage: A Review
by Rehan Anwar and M. Veronica Sofianos
Energies 2024, 17(11), 2572; https://doi.org/10.3390/en17112572 - 26 May 2024
Viewed by 1071
Abstract
This review article explores the critical role of additives in enhancing the performance and durability of thermochemical energy storage (TCES) materials, particularly in limestone-based systems. It evaluates various strategies, including hydration and the use of fine particles, along with additives like Al2 [...] Read more.
This review article explores the critical role of additives in enhancing the performance and durability of thermochemical energy storage (TCES) materials, particularly in limestone-based systems. It evaluates various strategies, including hydration and the use of fine particles, along with additives like Al2O3 and ZrO2, to address challenges like performance degradation and sintering over multiple cycles. Additionally, the review examines how multicyclic stability and material activity toward CO2 are related. It emphasizes the importance of selecting support materials that optimize both stability and reactivity. Furthermore, it highlights the need for systematic investigation into the selection, synthesis methods, and additive percentages to identify optimal formulations for improved multicyclic stability. Finally, it underscores the importance of understanding the mechanisms of interaction between additives and CaO/CaCO3 matrices to guide the design of effective additive-integrated systems. This comprehensive analysis provides valuable insights into current methodologies, emerging trends, and future directions for advancing sustainable energy storage technologies. Full article
Show Figures

Figure 1

21 pages, 623 KiB  
Article
Global Conditions and Changes in the Level of Renewable Energy Sources
by Jolanta Latosińska, Dorota Miłek and Łukasz Gibowski
Energies 2024, 17(11), 2553; https://doi.org/10.3390/en17112553 - 24 May 2024
Viewed by 935
Abstract
The progressing globalization of the contemporary economy impacts its volatility and unpredictability. The directions of changes in the socioeconomic development of the contemporary global economy are determined by a number of interrelated diverse factors. Factors clearly influencing the development of the modern international [...] Read more.
The progressing globalization of the contemporary economy impacts its volatility and unpredictability. The directions of changes in the socioeconomic development of the contemporary global economy are determined by a number of interrelated diverse factors. Factors clearly influencing the development of the modern international economy include innovation, digitization processes, instability of the economy caused by armed conflicts or pandemic outbreaks, the concept of sustainable development, climate policy, as well as issues related to the depletion of energy resources and the necessity of ensuring global energy security. The purpose of the article is to identify the factors of the development of the contemporary economy along with the analysis and evaluation of their impacts on changes in the level of renewable energy sources (RESs) in the EU countries. The time scope of the analysis covers the years 2013 and 2022 (a 10-year perspective). The study used the methods of literature study, literature criticism, statistical data analysis (statistical databases: EUROSTAT and IRENA), and linear ordering methods (TOPSIS and EDAS). The study results indicate that the levels of the RESs have changed in response to the factors diagnosed in the study. In the years studied, the leaders in terms of levels of RES development were France, Spain, and Denmark. Full article
Show Figures

Figure 1

10 pages, 4168 KiB  
Article
Sulfur Encapsulation into Carbon Nanospheres as an Effective Technique to Limit Sulfide Dissolution and Extend the Cycle Life of Lithium–Sulfur Batteries
by Wissam Fawaz, Zhao Wang and Ka Yuen Simon Ng
Energies 2024, 17(9), 2168; https://doi.org/10.3390/en17092168 - 1 May 2024
Viewed by 897
Abstract
Lithium–sulfur batteries suffer from a reduced cycle life and diminished coulombic efficiency, which is attributed to the polysulfide shuttle effect. We herein present a process for the fabrication of lithium–sulfur battery cathode material via the recrystallization of dissolved sulfur inside self-assembled carbon nanospheres [...] Read more.
Lithium–sulfur batteries suffer from a reduced cycle life and diminished coulombic efficiency, which is attributed to the polysulfide shuttle effect. We herein present a process for the fabrication of lithium–sulfur battery cathode material via the recrystallization of dissolved sulfur inside self-assembled carbon nanospheres synthesized through the carbonization of d-glucose. Trapping sulfur in the carbonaceous matrix lessens the rapid dissolution of polysulfides and minimizes the loss of active sulfur, thus extending the cycling stability of these batteries. The carbon–sulfur composite material was characterized via X-ray diffraction (XRD), field emission scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). Electrochemical analysis of the material and its functionality as an electrode for lithium–sulfur battery systems was evaluated in a coin cell format using impedance spectroscopy and a life cycle study. The as-prepared cathode has shown remarkable electrochemical performance with a specific capacity of 781 mA/g at 0.1 C after 500 charge/discharge cycles and 83.4% capacity retention. Full article
Show Figures

Figure 1

46 pages, 7204 KiB  
Review
Status and Development Perspectives of the Compressed Air Energy Storage (CAES) Technologies—A Literature Review
by Marcin Jankowski, Anna Pałac, Krzysztof Sornek, Wojciech Goryl, Maciej Żołądek, Maksymilian Homa and Mariusz Filipowicz
Energies 2024, 17(9), 2064; https://doi.org/10.3390/en17092064 - 26 Apr 2024
Cited by 3 | Viewed by 2047
Abstract
The potential energy of compressed air represents a multi-application source of power. Historically employed to drive certain manufacturing or transportation systems, it became a source of vehicle propulsion in the late 19th century. During the second half of the 20th century, significant efforts [...] Read more.
The potential energy of compressed air represents a multi-application source of power. Historically employed to drive certain manufacturing or transportation systems, it became a source of vehicle propulsion in the late 19th century. During the second half of the 20th century, significant efforts were directed towards harnessing pressurized air for the storage of electrical energy. Today’s systems, which are based on storing the air at a high pressure, are usually recognized as compressed air energy storage (CAES) installations. This paper aims to provide an overview of different technologies that take advantage of the energy accumulated in the compressed air. Particular attention is paid to the CAES installations that are working as electrical energy storage systems (EESs). These systems, developed originally as large capacity (>100 MWe) and fuel-based installations, may soon become fully scalable, highly efficient, and fuel-free electrical energy storage systems. To present this opportunity, a thorough review encompassing previous and up-to-date advancements in their development was carried out. In particular, CAES concepts, such as diabatic (D-CAES), adiabatic (A-CAES), and isothermal (I-CAES), are described in detail. This review also provides the detailed characteristics of the crucial elements of these configurations, including compressors, expanders, air storage chambers, and thermal storage tanks. Knowledge of these components and their role allows us to understand the main challenges behind the further development of the mentioned CAES setups. Apart from the CAES systems that are designed as EES systems, this paper describes other prospective technologies that utilize the energy of pressurized air. Accordingly, compressed air cars and their key elements are explained in detail. Moreover, the technology renowned as wave-driven compressed air energy storage (W-CAES) is described as well, indicating that the utilization of pressurized air represents a viable option for converting ocean energy into electrical power. Full article
Show Figures

Figure 1

31 pages, 5856 KiB  
Article
Proposal and Study of a Pumped Thermal Energy Storage to Improve the Economic Results of a Concentrated Solar Power That Works with a Hybrid Rankine–Brayton Propane Cycle
by Antonio Jesús Subires, Antonio Rovira and Marta Muñoz
Energies 2024, 17(9), 2005; https://doi.org/10.3390/en17092005 - 24 Apr 2024
Viewed by 1303
Abstract
This work proposes a pumped thermal energy storage (PTES) integrated into the power block of a concentrated solar power plant. The power block operates under a Hybrid Rankine–Brayton (HRB) cycle using propane as the working fluid. During PTES charging, some thermal energy is [...] Read more.
This work proposes a pumped thermal energy storage (PTES) integrated into the power block of a concentrated solar power plant. The power block operates under a Hybrid Rankine–Brayton (HRB) cycle using propane as the working fluid. During PTES charging, some thermal energy is obtained from a dedicated compressor (additional to that of the HRB cycle), which is stored. During discharge, both compressors (HRB and PTES) are off, restoring the consumed energy and resulting in about a 13% increase in nominal power output. The system is also able to store thermal energy that would otherwise be rejected through the condenser if the PTES were turned off, leading to efficiency improvements in some cases. Considering the 2022 Spanish electricity market prices, the proposed PTES integration with 4 h of storage is feasible. The levelized cost of storage is calculated and compared to those of other PTES systems, achieving around a 40% reduction compared with an equivalent PTES Rankine. These results encourage future studies where the proposed PTES could be integrated into other power cycles that include a recompression process. Full article
Show Figures

Figure 1

21 pages, 3893 KiB  
Article
Solution for Post-Mining Sites: Thermo-Economic Analysis of a Large-Scale Integrated Energy Storage System
by Jakub Ochmann, Michał Jurczyk, Krzysztof Rusin, Sebastian Rulik, Łukasz Bartela and Wojciech Uchman
Energies 2024, 17(8), 1970; https://doi.org/10.3390/en17081970 - 21 Apr 2024
Cited by 1 | Viewed by 1119
Abstract
The intensive development of renewable energy sources and the decreasing efficiency of conventional energy sources are reducing the flexibility of the electric power system. It becomes necessary to develop energy storage systems that allow reducing the differences between generation and energy demand. This [...] Read more.
The intensive development of renewable energy sources and the decreasing efficiency of conventional energy sources are reducing the flexibility of the electric power system. It becomes necessary to develop energy storage systems that allow reducing the differences between generation and energy demand. This article presents a multivariant analysis of an adiabatic compressed air energy storage system. The system uses a post-mining shaft as a reservoir of compressed air and also as a location for the development of a heat storage tank. Consideration was given to the length of the discharge stage, which directly affects the capital expenditure and operating schedule of the system. The basis for the analyses was the in-house numerical model, which takes into account the variability of air parameters during system operation. The numerical model also includes calculations of Thermal Energy Storage’s transient performance. The energy efficiency of the system operating on a daily cycle varies from 67.9% to 70.3%. Various mechanisms for economic support of energy storage systems were analyzed. The levelized cost of storage varies, depending on the variant, from 75.86 EUR/MWh for the most favorable case to 223.24 EUR/MWh for the least favorable case. Full article
Show Figures

Figure 1

12 pages, 1869 KiB  
Article
Comparison of Single-Phase Mathematical Models for Solid-State Packed Beds for Thermal Energy Storage
by Thomas Coates, Law Torres Sevilla, Burhan Saeed and Jovana Radulovic
Energies 2024, 17(8), 1842; https://doi.org/10.3390/en17081842 - 11 Apr 2024
Cited by 1 | Viewed by 1023
Abstract
This article presents an analytical solution for the evaluation of the thermal performance of packed bed sensible heat storage. The numerical model developed was tested for four different solid storage mediums. The thermal energy equation is solved numerically by deploying the finite difference [...] Read more.
This article presents an analytical solution for the evaluation of the thermal performance of packed bed sensible heat storage. The numerical model developed was tested for four different solid storage mediums. The thermal energy equation is solved numerically by deploying the finite difference method. The presented analytical solution is based on a novel mathematical approach. The numerical model was validated using the computer simulation package Comsol Multiphysics v5.3. Our numerical model results are in good agreement with the published experimental data, with an overall difference of ~10%. Hence, the numerical model is an efficient way of evaluating the thermal performance of packed bed thermal energy storage systems compared to other numerical strategies or computer simulation techniques. This proves that the novel analytical model has shown to be a reliable and broadly accurate approach to acquire the thermal performance of sensible heat storage. Full article
Show Figures

Figure 1

12 pages, 3711 KiB  
Article
Numerical Analysis of New PCM Thermal Storage Systems
by Giampietro Fabbri, Matteo Greppi and Federico Amati
Energies 2024, 17(7), 1772; https://doi.org/10.3390/en17071772 - 8 Apr 2024
Cited by 1 | Viewed by 1003
Abstract
In this paper, a thermal storage system based on a phase change material is proposed and investigated. The system is composed of several tubes that cross a phase change material mass. A fluid flowing in the tubes charges and discharges the heat storage [...] Read more.
In this paper, a thermal storage system based on a phase change material is proposed and investigated. The system is composed of several tubes that cross a phase change material mass. A fluid flowing in the tubes charges and discharges the heat storage system. A mathematical model of the system has been developed, which provides the time and space distribution of velocity, temperature, and liquid phase-changing material concentration in a non-stationary regime. A hybrid solution method based on finite volumes and finite differences techniques has been employed for the model equations in the MATLAB environment. To the tubes, a rectangular cross section has been assigned. The performance of the system in terms of accumulated energy density and accumulated power density has been investigated by varying some geometric parameters. The considered geometric parameters influence the number of tubes per unit of system width, the tube hydraulic resistance, the amount of phase change material around each tube, the heat transfer surface of the tube, and the heat storage velocity. In the parametric analysis, peaks have been evidenced in the investigated performance parameters at different instants after the beginning of the heat storage. Full article
Show Figures

Figure 1

19 pages, 3386 KiB  
Article
Differences and Causal Mechanisms in the Lithospheric Thermal Structures in the Cratons in East China: Implications for Their Geothermal Resource Potential
by Jinhui Wu, Yibo Wang, Lijuan He, Lijuan Wang, Junpeng Guan, Jun Chen, Zhuting Wang, Yaqi Wang and Shengbiao Hu
Energies 2024, 17(7), 1752; https://doi.org/10.3390/en17071752 - 6 Apr 2024
Viewed by 950
Abstract
The thermal structure of the lithosphere is key to understanding its thickness, properties, evolution, and geothermal resources. Cratons are known for their low heat flow and deep lithospheric roots. However, present-day cratons in East China have geothermal characteristics that are highly complex, with [...] Read more.
The thermal structure of the lithosphere is key to understanding its thickness, properties, evolution, and geothermal resources. Cratons are known for their low heat flow and deep lithospheric roots. However, present-day cratons in East China have geothermal characteristics that are highly complex, with variable heat flow values, diverging from the typical thermal state of cratons. In this study, we conducted a detailed analysis of the geothermal geological background of the cratons in East China, summarizing the thermal state and tectono-thermal processes of different tectonic units, calculating the temperature at various depths, and discussing differences in temperature and thermal reservoirs at different depths. The observed lithospheric thermal thickness within the North Jiangsu Basin and the Bohai Bay Basin is notably reduced in comparison to that of the Jianghan Basin and the Southern North China Basin. The phenomenon of craton destruction during the Late Mesozoic emerges as a pivotal determinant, enhancing the geothermal resource prospects of both the Bohai Bay Basin and the North Jiangsu Basin. Our findings contribute significantly to the augmentation of theoretical frameworks concerning the origins of heat sources in global cratons. Furthermore, they offer invaluable insights for the methodical exploration, evaluation, advancement, and exploitation of geothermal resources. Full article
Show Figures

Figure 1

16 pages, 20102 KiB  
Article
Joint Estimation of SOC and SOH for Lithium-Ion Batteries Based on Dual Adaptive Central Difference H-Infinity Filter
by Bingyu Sang, Zaijun Wu, Bo Yang, Junjie Wei and Youhong Wan
Energies 2024, 17(7), 1640; https://doi.org/10.3390/en17071640 - 29 Mar 2024
Cited by 4 | Viewed by 1357
Abstract
The accurate estimation of the state-of-charge (SOC) and state-of-health (SOH) of lithium-ion batteries is crucial for the safe and reliable operation of battery systems. In order to overcome the practical problems of low accuracy, slow convergence and insufficient robustness in the existing joint [...] Read more.
The accurate estimation of the state-of-charge (SOC) and state-of-health (SOH) of lithium-ion batteries is crucial for the safe and reliable operation of battery systems. In order to overcome the practical problems of low accuracy, slow convergence and insufficient robustness in the existing joint estimation algorithms of SOC and SOH, a Dual Adaptive Central Difference H-Infinity Filter algorithm is proposed. Firstly, the Forgetting Factor Recursive Least Squares (FFRLS) algorithm is employed for parameter identification, and an inner loop with multiple updates of the parameter estimation vector is added to improve the accuracy of parameter identification. Secondly, the capacity is selected as the characterization of SOH, and the open circuit voltage and capacity are used as the state variables for capacity estimation to improve its convergence speed. Meanwhile, considering the interaction between SOC and SOH, the state space equations of SOC and SOH estimation are established. Moreover, the proposed algorithm introduces a robust discrete H-infinity filter equation to improve the measurement update on the basis of the central differential Kalman filter with good accuracy, and combines the Sage–Husa adaptive filter to achieve the joint estimation of SOC and SOH. Finally, under Urban Dynamometer Driving Schedule (UDDS) and Highway Fuel Economy Test (HWFET) conditions, the SOC estimation errors are 0.5% and 0.63%, and the SOH maximum estimation errors are 0.73% and 0.86%, indicating that the proposed algorithm has higher accuracy compared to the traditional algorithm. The experimental results at different initial values of capacity and SOC demonstrate that the proposed algorithm showcases enhanced convergence speed and robustness. Full article
Show Figures

Figure 1

20 pages, 65866 KiB  
Article
Classification of Highly Imbalanced Supervisory Control and Data Acquisition Data for Fault Detection of Wind Turbine Generators
by Jorge Maldonado-Correa, Marcelo Valdiviezo-Condolo, Estefanía Artigao, Sergio Martín-Martínez and Emilio Gómez-Lázaro
Energies 2024, 17(7), 1590; https://doi.org/10.3390/en17071590 - 26 Mar 2024
Cited by 1 | Viewed by 938
Abstract
It is common knowledge that wind energy is a crucial, strategic component of the mix needed to create a green economy. In this regard, optimizing the operations and maintenance (O&M) of wind turbines (WTs) is key, as it will serve to reduce the [...] Read more.
It is common knowledge that wind energy is a crucial, strategic component of the mix needed to create a green economy. In this regard, optimizing the operations and maintenance (O&M) of wind turbines (WTs) is key, as it will serve to reduce the levelized cost of electricity (LCOE) of wind energy. Since most modern WTs are equipped with a Supervisory Control and Data Acquisition (SCADA) system for remote monitoring and control, condition-based maintenance using SCADA data is considered a promising solution, although certain drawbacks still exist. Typically, large amounts of normal-operating SCADA data are generated against small amounts of fault-related data. In this study, we use high-frequency SCADA data from an operating WT with a significant imbalance between normal and fault classes. We implement several resampling techniques to address this challenge and generate synthetic generator fault data. In addition, several machine learning (ML) algorithms are proposed for processing the resampled data and WT generator fault classification. Experimental results show that ADASYN + Random Forest obtained the best performance, providing promising results toward wind farm O&M optimization. Full article
Show Figures

Figure 1

15 pages, 1254 KiB  
Review
Unlocking Geothermal Energy: A Thorough Literature Review of Lithuanian Geothermal Complexes and Their Production Potential
by Abdul Rashid Memon, Pijus Makauskas, Ieva Kaminskaite-Baranauskiene and Mayur Pal
Energies 2024, 17(7), 1576; https://doi.org/10.3390/en17071576 - 26 Mar 2024
Viewed by 900
Abstract
Lithuania is located on the East of Baltic sedimentary basin and has a geothermal anomaly situated in the southwestern region of the country. There are two primary geothermal complexes within the anomaly, composed of Cambrian and Devonian aquifers. The Cambrian formation is composed [...] Read more.
Lithuania is located on the East of Baltic sedimentary basin and has a geothermal anomaly situated in the southwestern region of the country. There are two primary geothermal complexes within the anomaly, composed of Cambrian and Devonian aquifers. The Cambrian formation is composed of sandstones that have a reservoir temperature reaching up to 96 °C (depth > 2000 m). The Devonian aquifer is composed of unconsolidated sands of Parnu–Kemeri and has a reservoir temperature of up to 46 °C (depth > 1000 m). Historically, both formations have been investigated for geothermal energy production. In this article, we present a detailed literature review of the geothermal work carried out on both formations, including past, present, and some possible future studies. The study presented in this paper highlights the key findings of previous research work, summarizes the research gaps, and then elaborates on the possible applications of emerging technologies to bridge the research gaps and improve our understanding of geothermal complexes in Lithuania. Although it is not the main aim of this article, this article also touches upon the important need to develop 2D/3D numerical models, to quantify uncertainties, in the evaluation of the geothermal potential in Lithuania for commercial development. This study also highlights possibilities of extending geothermal development to depleted hydrocarbon reservoirs through repurposing the high-water-production wells. Moreover, from the literature review, it can be concluded that the Lithuanian geothermal aquifers are hyper-saline in nature and temperature changes lead to the deposition of salts both upstream and downstream of the reservoir. Therefore, there is a need for developing multiphysics thermo-mechanical–chemical (THMC) models for evaluation of reservoir behavior. The literature also describes the potential use and development of the THMC model as a part of future work that must be carried out. Full article
Show Figures

Figure 1

22 pages, 458 KiB  
Review
A Review of Energy Overconsumption Reduction Methods in the Utilization Stage in Compressed Air Systems
by Dominik Gryboś and Jacek S. Leszczyński
Energies 2024, 17(6), 1495; https://doi.org/10.3390/en17061495 - 21 Mar 2024
Viewed by 1346
Abstract
Pneumatic systems use the energy of compressed air to carry out manufacturing automation processes through the implementation of complex handling and motion tasks. However, these systems are energy intensive: it is estimated that pneumatic systems in manufacturing plants consume approximately 10% of all [...] Read more.
Pneumatic systems use the energy of compressed air to carry out manufacturing automation processes through the implementation of complex handling and motion tasks. However, these systems are energy intensive: it is estimated that pneumatic systems in manufacturing plants consume approximately 10% of all electricity consumed in the industrial sector. At the same time, the energy efficiency of the whole pneumatic system is observed to be 6–10%, due to the compression process, oversizing, and overconsumption. There are numerous solutions in the literature focusing on improving efficiency at the compression stage of utilization; however, for the utilization stage, there is a lack of systematization and grouping of these solutions. The following review will summarize current knowledge about the utilization stage and methods for improving oversizing and energy overconsumption. In addition, a method of exergy analysis for pneumatic systems will be presented, which is a very useful tool to assess the efficiency of these systems. Full article
Show Figures

Figure 1

26 pages, 5153 KiB  
Article
Adaptation of Microinverter Reference Design for Integration with Battery Energy Storage Systems in Microgrids
by Danijel Jolevski, Damir Jakus, Josip Vasilj and Joško Novaković
Energies 2024, 17(6), 1487; https://doi.org/10.3390/en17061487 - 20 Mar 2024
Viewed by 940
Abstract
The paper presents an adaptation of the microinverter platform from Texas Instruments to incorporate a battery energy storage system (BESS) alongside the development of the BESS system itself. Initially designed for unidirectional power flow between PV panels and an electric grid, the platform [...] Read more.
The paper presents an adaptation of the microinverter platform from Texas Instruments to incorporate a battery energy storage system (BESS) alongside the development of the BESS system itself. Initially designed for unidirectional power flow between PV panels and an electric grid, the platform required modifications to accommodate bidirectional energy transfer for BESS integration. These modifications encompass software adjustments and hardware enhancements, which are all detailed within the paper. The electrical configuration includes selecting and deploying components such as DCDC power converters, microcontrollers, measured signals, and actuating signals to facilitate battery connection to the platform’s DC bus. Furthermore, a supervisory control and data acquisition (SCADA) system is devised for supervisory control and monitoring, with its implementation outlined. Control software tailored for the chosen microcontroller of the DCDC converters is described in terms of structure and functionality. A hardware-in-the-loop (HIL) methodology is employed to validate the proposed modifications and microgrid configuration. Utilizing the real-time simulator OPAL-RT, the paper presents experimental results and their analysis within the considered microgrid environment. Full article
Show Figures

Figure 1

30 pages, 4706 KiB  
Article
Sizing of Battery Energy Storage Systems for Firming PV Power including Aging Analysis
by Juan A. Tejero-Gómez and Ángel A. Bayod-Rújula
Energies 2024, 17(6), 1485; https://doi.org/10.3390/en17061485 - 20 Mar 2024
Viewed by 1718
Abstract
The variability of solar radiation presents significant challenges for the integration of solar photovoltaic (PV) energy into the electrical system. Incorporating battery storage technologies ensures energy reliability and promotes sustainable growth. In this work, an energy analysis is carried out to determine the [...] Read more.
The variability of solar radiation presents significant challenges for the integration of solar photovoltaic (PV) energy into the electrical system. Incorporating battery storage technologies ensures energy reliability and promotes sustainable growth. In this work, an energy analysis is carried out to determine the installation size and the operating setpoint with optimal constant monthly power through an iterative calculation process, considering various operating setpoints and system parameters. A degradation model is integrated according to the curves offered by battery manufacturers and the charge–discharge cycles are calculated using the rainflow method to guarantee a reliable analysis of the plant. Through massive data analysis in a long-term simulation, indicators are generated that allow for establishing a relationship between the energy unavailability of the system and the BESS dimensions. Full article
Show Figures

Figure 1

18 pages, 4409 KiB  
Article
Assessing Geothermal Energy Production Potential of Cambrian Geothermal Complexes in Lithuania
by Pijus Makauskas, Ieva Kaminskaite-Baranauskiene, Abdul Rashid Abdul Nabi Memon and Mayur Pal
Energies 2024, 17(5), 1054; https://doi.org/10.3390/en17051054 - 23 Feb 2024
Cited by 1 | Viewed by 1054
Abstract
Lithuania has a geothermal anomaly situated in the southwestern region of the country. This anomaly is comprised of two primary geothermal complexes located in western Lithuania. The first complex is characterized by the Pärnu–Kemeri Devonian sandstone aquifers, which exhibit exceptionally good flow properties. [...] Read more.
Lithuania has a geothermal anomaly situated in the southwestern region of the country. This anomaly is comprised of two primary geothermal complexes located in western Lithuania. The first complex is characterized by the Pärnu–Kemeri Devonian sandstone aquifers, which exhibit exceptionally good flow properties. However, the reservoir temperatures in this complex only reach up to 45 °C. The second complex encompasses Cambrian sandstone reservoirs. Although these Cambrian sandstone reservoirs exhibit high temperatures, with the highest reservoir temperatures reaching up to 96 °C, these Cambrian sandstone reservoirs have less favorable petrophysical properties. This study focuses on the high temperature Cambrian Geothermal sandstone reservoirs. The study aims to conduct a geological screening of the existing and depleted hydrocarbon reservoirs with high water production rates. After initial data gathering, numerical modeling is employed with the help of mechanistic box models to evaluate the geothermal potential of the selected sites for commercial development. Ultimately, the study identifies the top five screened sites, which could be developed further for techno-economical modelling. Full article
Show Figures

Figure 1

12 pages, 2992 KiB  
Article
Thermal Evolution of NiFe-NO3 LDH and Its Application in Energy Storage Systems
by Marco Fortunato, Andrea Pietro Reverberi, Bruno Fabiano and Anna Maria Cardinale
Energies 2024, 17(5), 1035; https://doi.org/10.3390/en17051035 - 22 Feb 2024
Cited by 1 | Viewed by 960
Abstract
In this work, the performances of nickel iron layered double hydroxides (LDH) with the nitrate anion at the interlayer (NiFe-NO3) for the manufacture of anodes for lithium-ion batteries have been tested before and after its sintering at different temperatures. After synthesis, [...] Read more.
In this work, the performances of nickel iron layered double hydroxides (LDH) with the nitrate anion at the interlayer (NiFe-NO3) for the manufacture of anodes for lithium-ion batteries have been tested before and after its sintering at different temperatures. After synthesis, the material was thermally analyzed in a range 30–1250 °C, showing a mass loss occurring in three different consecutive steps leading to a total mass decrease of ~30 mass%. Following thermogravimetric analysis (TGA), four samples were prepared by annealing at four different temperatures: one of the four did not undergo a thermal treatment (NiFe-0), while the remaining three were annealed at 250 °C, 360 °C, and 560 °C for 6 h (NiFe-250, NiFe-360, and NiFe-560). All materials where completely characterized via FE-SEM, PXRD, and FT-IR. The pristine LDH material showed some structural and compositional changes for growing temperatures, starting from the typical turbostratic hexagonal structure through a mixture of amorphous metal oxides and finally to the stoichiometric oxides FeNi2O4 and NiO. The as-obtained materials were mixed with carbon black (C65) and sodium alginate and tested as electrodes in Swagelok half cells in LP30 vs. metallic Li to perform CV and GCPL analysis. The electrochemical tests showed that the performances of NiFe-0, both in terms of stability and specific capacity, are not so different from the one of the NiFe-560, even if the Ni mass% in the former is lower than in the NiFe-560. This phenomenon could be explained by assuming a combined mechanism of reaction involving both intercalation and conversion. Full article
Show Figures

Figure 1

16 pages, 2923 KiB  
Article
Assessing the Performance of Continuous-Flow Microbial Fuel Cells and Membrane Electrode Assembly with Electrodeposited Mn Oxide Catalyst
by Laura Mais, Michele Mascia and Annalisa Vacca
Energies 2024, 17(4), 943; https://doi.org/10.3390/en17040943 - 17 Feb 2024
Viewed by 1118
Abstract
Microbial fuel cells (MFCs) are considered promising energy sources whereby chemical energy is converted into electricity via bioelectrochemical reactions utilizing microorganisms. Several factors affect MFC performance, including cathodic reduction of oxygen, electrode materials, cell internal and external resistances, and cell design. This work [...] Read more.
Microbial fuel cells (MFCs) are considered promising energy sources whereby chemical energy is converted into electricity via bioelectrochemical reactions utilizing microorganisms. Several factors affect MFC performance, including cathodic reduction of oxygen, electrode materials, cell internal and external resistances, and cell design. This work describes the effect of the catalyst coating in the air-cathode membrane electrode assembly (MEA) for a microbial fuel cell (MFC) prepared via electrodeposition of manganese oxide. The characterization of the synthesized air-cathode MFC, operating in a continuous mode, was made via electrochemical impedance spectroscopy (EIS) analyses for the determination of the intrinsic properties of the electrode that are crucial for scalability purposes. EIS analysis of the MFCs and of the MEA reveals that the anode and cathode contribute to polarization resistance by about 85% and 15%, respectively, confirming the high catalytic activity of the Mn-based air cathode. The maximum power density of the Mn-based cathode is about 20% higher than that recorded using a Pt/C electrode. Full article
Show Figures

Figure 1

2023

Jump to: 2024, 2022, 2021, 2020

30 pages, 13117 KiB  
Article
Experimental and Numerical Study of Novel Vortex Bladeless Wind Turbine with an Economic Feasibility Analysis and Investigation of Environmental Benefits
by Hasan Hamdan, Sharul Sham Dol, Abdelrahman Hosny Gomaa, Aghyad Belal Al Tahhan, Ahmad Al Ramahi, Haya Fares Turkmani, Mohammad Alkhedher and Rahaf Ajaj
Energies 2024, 17(1), 214; https://doi.org/10.3390/en17010214 - 30 Dec 2023
Cited by 1 | Viewed by 3998
Abstract
This study combines experimental and numerical evaluations of Vortex Bladeless Wind Turbines (VBWTs) to understand their potential in renewable energy generation. The methodology employs Two-Way Fluid–Solid Interface (FSI) simulations, alongside real-world data, providing important insights into the turbine’s vibration dynamics and flow interactions [...] Read more.
This study combines experimental and numerical evaluations of Vortex Bladeless Wind Turbines (VBWTs) to understand their potential in renewable energy generation. The methodology employs Two-Way Fluid–Solid Interface (FSI) simulations, alongside real-world data, providing important insights into the turbine’s vibration dynamics and flow interactions during operation. Key findings include identifying optimal vibration frequencies and amplitudes that enhance energy harvesting and a clear advantage in power-generation estimations shown by one of the models used. The study reveals possible applications of VBWT in various settings like airport runways, highways, and buildings, indicating a promising avenue for incorporating such renewable-energy solutions. Discussions on the economic feasibility and environmental benefits of VBWT deployment are also presented, suggesting a need for further research and optimization in this area. A conceptual generator design and business model are introduced as part of a broader discussion on technology integration and energy storage. The research in this study encompasses experimental and numerical analysis, to achieve a broader understanding of the workings of a VBWT, realizing the feasibility of using such systems in lower-wind-speed conditions and upscaling to higher-wind-speed cases. Full article
Show Figures

Figure 1

17 pages, 4299 KiB  
Perspective
The Role of Education and Science-Driven Tools in Scaling Up Photovoltaic Deployment
by Ana M. Martínez, Christian Thiel, Sandor Szabo, Imen Gherboudj, René van Swaaij, Andreea Tanasa, Arnulf Jäger-Waldau, Nigel Taylor and Arno Smets
Energies 2023, 16(24), 8065; https://doi.org/10.3390/en16248065 - 14 Dec 2023
Cited by 1 | Viewed by 1048
Abstract
Accelerating the deployment of Photovoltaic (PV) systems is a key contributing factor in achieving climate neutrality. Even though solar power is one of the cheapest energy sources and its deployment is growing rapidly around the world, an even faster growth is required to [...] Read more.
Accelerating the deployment of Photovoltaic (PV) systems is a key contributing factor in achieving climate neutrality. Even though solar power is one of the cheapest energy sources and its deployment is growing rapidly around the world, an even faster growth is required to achieve existing climate goals. Besides the role that finance and permitting can play as enablers or barriers to this, the key elements to enable fast PV deployment are the use of education, and science and data-driven tools to empower citizens, installers, and investors to make their decisions based on robust scientific evidence. This perspective article aims to summarize the key concepts presented and discussed during the side event at COP27 on PV resources towards climate neutrality. The article will accomplish this by highlighting two key aspects: (1) the advantages of using solar-related education and data-driven tools, and (2) showcasing the significance of education, improved data and tools, community involvement, and PV mapping in expediting the deployment of PV systems. Full article
Show Figures

Figure 1

32 pages, 8722 KiB  
Review
Power Generation with Renewable Energy and Advanced Supercritical CO2 Thermodynamic Power Cycles: A Review
by Xinyu Zhang and Yunting Ge
Energies 2023, 16(23), 7781; https://doi.org/10.3390/en16237781 - 26 Nov 2023
Cited by 3 | Viewed by 2101
Abstract
Supercritical CO2 (S-CO2) thermodynamic power cycles have been considerably investigated in the applications of fossil fuel and nuclear power generation systems, considering their superior characteristics such as compactness, sustainability, cost-effectiveness, environmentally friendly working fluid and high thermal efficiency. They can [...] Read more.
Supercritical CO2 (S-CO2) thermodynamic power cycles have been considerably investigated in the applications of fossil fuel and nuclear power generation systems, considering their superior characteristics such as compactness, sustainability, cost-effectiveness, environmentally friendly working fluid and high thermal efficiency. They can be potentially integrated and applied with various renewable energy systems for low-carbon power generation, so extensive studies in these areas have also been conducted substantially. However, there is a shortage of reviews that specifically concentrate on the integrations of S-CO2 with renewable energy, encompassing biomass, solar, geothermal and waste heat. It is thus necessary to provide an update and overview of the development of S-CO2 renewable energy systems and identify technology and integration opportunities for different types of renewable resources. Correspondingly, this paper not only summarizes the advantages of CO2 working fluid, design layouts of S-CO2 cycles and classifications of renewable energies to be integrated but also reviews the recent research activities and studies carried out worldwide on advanced S-CO2 power cycles with renewable energy. Moreover, the performance and development of various systems are well grouped and discussed. Full article
Show Figures

Figure 1

14 pages, 11097 KiB  
Article
Two-Dimensional Geothermal Model of the Peruvian Andes above the Nazca Ridge Subduction
by Sara Ciattoni, Stefano Mazzoli, Antonella Megna, Matteo Basilici and Stefano Santini
Energies 2023, 16(23), 7697; https://doi.org/10.3390/en16237697 - 21 Nov 2023
Cited by 1 | Viewed by 1128
Abstract
The aseismic Nazca Ridge produces localized flat-slab subduction beneath the South American margin at latitudes 10° to 15° S. The geological evolution and the spatio-temporal pattern of deformation of the upper plate have been strongly influenced by the presence of the flat slab. [...] Read more.
The aseismic Nazca Ridge produces localized flat-slab subduction beneath the South American margin at latitudes 10° to 15° S. The geological evolution and the spatio-temporal pattern of deformation of the upper plate have been strongly influenced by the presence of the flat slab. In this study, we investigated the lithospheric thermal structure of this region by elaborating a 2D geothermal model along a section across the top of the Nazca Ridge, the Peru–Chile trench, the Andean Cordillera, and the Amazonian Basin, for a total length of 1000 km. For the sake of modelling, the crust of the overriding plate was subdivided into two parts, i.e., a sedimentary cover (including the entire lithostratigraphic sequence) and a crystalline basement. Applying an analytical methodology, we calculated geotherms and isotherms by setting (i) thickness, (ii) density, (iii) heat production, and (iv) thermal conductivity for each geological unit and considering (v) heat flux at the Moho, (vi) frictional heating produced by faults, and (vii) plate convergence rate. The resulting model could make a significant advance in our understanding of how flat slab geometry associated with the Nazca Ridge subduction affects the thermal structure and hence the tectonic evolution of the region. Full article
Show Figures

Figure 1

20 pages, 3555 KiB  
Article
What Is the Impact of the Renewable Energy Power Absorption Guarantee Mechanism on China’s Green Electricity Market?
by Yan Lu, Xuan Liu, Hongjian Li, Haoran Wang, Jiajie Kong, Cheng Zhong, Mingli Cui, Yan Li, Xiaoqi Sun, Jiadong Xuan and Tiantian Feng
Energies 2023, 16(21), 7434; https://doi.org/10.3390/en16217434 - 3 Nov 2023
Cited by 2 | Viewed by 1356
Abstract
In order to accelerate the construction of a clean, low-carbon, safe and efficient energy system, China set the provincial weight of responsibility for renewable energy power consumption and established a renewable energy power absorption guarantee mechanism in 2019. As a market incentive policy, [...] Read more.
In order to accelerate the construction of a clean, low-carbon, safe and efficient energy system, China set the provincial weight of responsibility for renewable energy power consumption and established a renewable energy power absorption guarantee mechanism in 2019. As a market incentive policy, it has enduring effect on the low-carbon transformation of the power industry. Firstly, the operation mechanism of the renewable energy consumption guarantee mechanism is analyzed. The general framework, core elements and supporting measures are clarified. Secondly, a stock-flow diagram is constructed based on the system dynamics method. It contains the green electricity market sub-module, the green-certificate market sub-module and the excess power absorption market sub-module. Finally, multiple scenarios are set up to simulate the impact of the green-certificate market and excess power absorption market improvements on the installed capacity and tariff of China’s green power market. The renewable energy guarantee mechanism is an effective means to promote the consumption of green electricity in China. In addition, in the short term the cost of electricity for users has increased, but in the long term the cost of electricity shows a fluctuating downward trend. This study provides theoretical references for the formulation of clean and low-carbon policy objectives in the power industry and the optimization of market mechanisms. Full article
Show Figures

Figure 1

23 pages, 3551 KiB  
Article
Theoretical and Energy Biomass Potential of Heat and Electricity Production in Kosovo
by Ardit Sertolli, Attila Bai, Zoltán Gabnai, Tamás Mizik and Albiona Pestisha
Energies 2023, 16(20), 7209; https://doi.org/10.3390/en16207209 - 23 Oct 2023
Cited by 2 | Viewed by 1917
Abstract
The energy use of residues from agriculture, forestry, and solid waste can foster the transition towards a more renewable energy supply. This paper analyzes the energy potential of the above-mentioned sources for energy applications in Kosovo. The analysis is based on statistical data [...] Read more.
The energy use of residues from agriculture, forestry, and solid waste can foster the transition towards a more renewable energy supply. This paper analyzes the energy potential of the above-mentioned sources for energy applications in Kosovo. The analysis is based on statistical data from different studies and reports, analyzing and calculating them to determine the theoretical and energy biomass potential. Kosovo can increase its self-sufficiency by taking advantage of its rich but under-utilized potential of biomass energy sources. This is a novelty study in this area, considering Kosovo lignite-dominated heat energy and electricity consumption and the available special literature. According to our estimates, the theoretical potential is 6.13 million tons/year, while the biomass energy potential should be around 4.57 million tons/year, including approximately 74.6% of biomass, which can be used for energy needs (heating and electricity). Based on the data and calculations, the available and usable potential shows biomass as an energy source with high potential in Kosovo; its share is very low, but it is reasonable to grow for both environmental and economic reasons. Full article
Show Figures

Figure 1

17 pages, 2791 KiB  
Article
Analysis of Frequency Regulation Capability of Doubly Fed Induction Generator and Supercapacitor Energy Storage Based on Dynamic Power Flow
by Tingting Sun, Hongru Shi, Lei Ren and Jiejie Huang
Energies 2023, 16(20), 7059; https://doi.org/10.3390/en16207059 - 12 Oct 2023
Viewed by 989
Abstract
The grid-integrated doubly fed induction generator (DFIG) is required to participate in the frequency regulation of the power system. The supercapacitor energy storage (SES) is capable of enhancing the frequency regulation capability of the DFIG in a coupled manner. The SES is connected [...] Read more.
The grid-integrated doubly fed induction generator (DFIG) is required to participate in the frequency regulation of the power system. The supercapacitor energy storage (SES) is capable of enhancing the frequency regulation capability of the DFIG in a coupled manner. The SES is connected to the DC capacitor of the DFIG and provides active power response through the droop control. The dynamic power flow (DPF) model is established to quantify the frequency response of the power system when the DFIG-SES system participates in the frequency regulation. The integration of the SES affects the internal power flow distribution of the DFIG; thus, the detailed model of the DFIG is incorporated into the DPF analysis. Considering the different response speeds of the synchronous generator (SG), the SES, and the DFIG to the frequency regulation, the first-order inertia delay in the governor control of the SG is included in the DPF model. The impact of the delay time constant on the continued operation time of the SES is analyzed. With the same deloading percentage, the output power of the DFIG is adjusted based on a variable droop coefficient scheme to fully utilize its active power reserve. The feasibility and effectiveness of the DFIG-SES scheme to participate in the frequency regulation are analyzed based on the DPF and verified through numerical analysis. Full article
Show Figures

Figure 1

17 pages, 16478 KiB  
Article
Detection of Manufacturing Defects in Lithium-Ion Batteries-Analysis of the Potential of Computed Tomography Imaging
by Daniel Evans, Paul-Martin Luc, Claas Tebruegge and Julia Kowal
Energies 2023, 16(19), 6958; https://doi.org/10.3390/en16196958 - 5 Oct 2023
Cited by 1 | Viewed by 3529
Abstract
Realising an ideal lithium-ion battery (LIB) cell characterised by entirely homogeneous physical properties poses a significant, if not an impossible, challenge in LIB production. Even the slightest deviation in a process parameter in its production leads to inhomogeneities and causes a deviation in [...] Read more.
Realising an ideal lithium-ion battery (LIB) cell characterised by entirely homogeneous physical properties poses a significant, if not an impossible, challenge in LIB production. Even the slightest deviation in a process parameter in its production leads to inhomogeneities and causes a deviation in performance parameters of LIBs within the same batch. The greater the number and/or intensity of inhomogeneities, the more they need to be avoided. Severe inhomogeneities (defects), such as metal particle contamination, significantly impact the cell’s performance. Besides electrical measurements, image-based measurement methods can be used to identify defects and, thus, ensure the production quality and safety of LIBs. While the applicability of computed tomography (CT) as an image-based measurement method for detecting defects has been proven, the limitations of this method still need to be determined. In this study, a systematic analysis of the capabilities of CT imaging was conducted. A multilayer pouch cell without an electrolyte was reassembled with several defects on one of the middle anodes. To investigate the boundaries of CT, defects such as a partial and complete removal of the coating, a cut, or a kink, as well as particle contaminations of various sizes and materials (aluminium, copper, iron) were chosen. By comparing the CT images of the cell using laser scanning microscope images of the defective anode, it could be proven that all selected defects except the kink were detectable. Full article
Show Figures

Figure 1

23 pages, 943 KiB  
Article
Application of Circular Thermoeconomics to the Diagnosis of Energy Systems
by Antonio Valero and César Torres
Energies 2023, 16(18), 6751; https://doi.org/10.3390/en16186751 - 21 Sep 2023
Viewed by 1034
Abstract
This paper reviews the fundamentals of the thermoeconomic diagnosis theory. Thermoeconomic diagnosis is one of the main applications of the exergy cost theory used to identify the causes of additional resource consumption of a system due to inefficiencies in its components, published in [...] Read more.
This paper reviews the fundamentals of the thermoeconomic diagnosis theory. Thermoeconomic diagnosis is one of the main applications of the exergy cost theory used to identify the causes of additional resource consumption of a system due to inefficiencies in its components, published in the late 1990s. Thermoeconomic diagnosis has usually been applied to diagnose power plants with high consumption of fossil fuels and fixed production. However, it does not consider the final production and waste generation variation. In this paper, Circular Thermoeconomics is applied to analyze in depth the effect of malfunctions on additional waste generation and changes in the final output of the system. This new formulation can be applied to polygeneration systems, where there is a simultaneous variation of final products, and to process integration and industrial symbiosis, where a part of the waste generated by a plant could be reused in other processes or plants. Full article
Show Figures

Figure 1

33 pages, 2788 KiB  
Review
From Lab to Fab: Development and Deployment of Direct Air Capture of CO2
by Vahid Barahimi, Monica Ho and Eric Croiset
Energies 2023, 16(17), 6385; https://doi.org/10.3390/en16176385 - 3 Sep 2023
Cited by 3 | Viewed by 6852
Abstract
Direct Air Capture (DAC) is a promising technology to fight climate change by capturing carbon dioxide (CO2) from the air. For DAC to be a negative emissions technology, the captured CO2 must be removed permanently, but can also be used [...] Read more.
Direct Air Capture (DAC) is a promising technology to fight climate change by capturing carbon dioxide (CO2) from the air. For DAC to be a negative emissions technology, the captured CO2 must be removed permanently, but can also be used as a net-zero technology to produce sustainable chemicals, fuels or other materials. This review presents a comprehensive survey of recent advancements, challenges, and potential applications of DAC technology, with an emphasis on the recent rapid increase in the number of DAC developers, the majority of them being founded in the past 4 years. Through pilot projects and recent commercial deployments, several DAC companies have made significant advances and demonstrated their scalability. Cost and energy efficiency remain significant impediments to the wide deployment of DAC. Integration with emission-free energy sources and utilization of waste heat are being researched to boost the total energy efficiency of DAC systems. Further research of electrochemical technologies for regeneration or direct capture are needed, as well as the development of new, modified, or hybrid adsorbents for improved capture efficiencies. Moreover, favorable regulations and financial incentives are crucial for enhancing the viability of DAC projects and will need to substantially increase if Paris Agreement goals are to be achieved. Full article
Show Figures

Figure 1

30 pages, 1502 KiB  
Article
Evolutionary Analysis of the Solar Photovoltaic Products Trade Network in Belt and Road Initiative Countries from an Economic Perspective
by Liusuo Hu, Jian Hu and Weilung Huang
Energies 2023, 16(17), 6371; https://doi.org/10.3390/en16176371 - 2 Sep 2023
Cited by 3 | Viewed by 2781
Abstract
Against the backdrop of global energy transition and the imperative for sustainable development, the trade dynamics of solar photovoltaic (PV) products among “Belt and Road Initiative (BRI)” countries gained momentum. This study investigates the evolving trade patterns of PV products within BRI nations, [...] Read more.
Against the backdrop of global energy transition and the imperative for sustainable development, the trade dynamics of solar photovoltaic (PV) products among “Belt and Road Initiative (BRI)” countries gained momentum. This study investigates the evolving trade patterns of PV products within BRI nations, alongside the underlying determinants. The paper constructs and analyzes a solar PV product trade network, elucidating evolutionary trends, structural complexities, and clusters. A novel centrality influence model explores influencing factors across five dimensions. Methodologically, trade data, the “Five Connectivity” framework, and socio-economic indicators from 2001 to 2022 across 65 BRI countries underpin the study. Empirical insights reveal a robust PV product trade network with density exceeding 0.4 and reciprocity surpassing 0.38. China’s rising centrality, reflected in a weighted degree surge from 14.38 to 79.37 since 2011, signifies its consolidation within the network. Results show sustained high density and reciprocity in the PV trade network, signaling robust communication among BRI countries. China’s centrality in the network has consistently grown since 2011. Trade cluster analysis reveals isolated segments predominant, depicting emerging economies with limited photovoltaic exchanges, mainly export-focused. The study highlights the pivotal role of “Five Connectivity” dimensions in promoting PV trade, while financial connectivity’s impact remains modest. The emergence of PV product centers challenges traditional energy hubs, prompting the need for new energy trading paradigms and robust financial hubs. Full article
Show Figures

Figure 1

12 pages, 715 KiB  
Article
The Economic Value of New Sustainable Products: The Case of Photovoltaic Thermal (PVT) Hybrid Solar Collectors
by Jeongbin Lee and Jungwoo Shin
Energies 2023, 16(14), 5473; https://doi.org/10.3390/en16145473 - 19 Jul 2023
Viewed by 1256
Abstract
Among green energy technologies, solar power is a promising technology in the net-zero era of the power industry. Conventional solar modules have decreasing efficiency weaknesses as the temperature rises, whereas photovoltaic thermal (PVT) systems do not remove heat from the module or lower [...] Read more.
Among green energy technologies, solar power is a promising technology in the net-zero era of the power industry. Conventional solar modules have decreasing efficiency weaknesses as the temperature rises, whereas photovoltaic thermal (PVT) systems do not remove heat from the module or lower the temperature. However, the profitability of PVT systems has been underestimated. The profitability of new convergence products, such as PVT technology, entering the market for the first time allows for the evaluation of the appropriate starting price and policy requirements to support the product’s market entrance. We used the contingent valuation method (CVM) to solve this problem. The survey derived the respondents’ mean willingness to pay (WTP) and the total amount of social benefits. Among these CVM models, the one-and-one-half-bound (OOHB) spike model was used to distinguish zero WTP. Based on a survey of 300 households, respondents were willing to pay an additional yearly average income tax of KRW 10,608 (USD 7.90), and the total social benefit of PVT technology was calculated to be KRW 145 billion (USD 108 million). This result shows that individuals evaluate the value of PVT as 3.69% of their monthly electricity bill and 2.8% of their monthly gas bill. Several additional factors that influence WTP were analyzed, indicating a high possibility of PVT adoption by individuals who have replaced or are planning to replace photovoltaic (PV) modules. This study is significant because it examines the economic value of PVT and proposes a focus group for the effective market entry of new carbon neutrality products. Full article
Show Figures

Figure 1

23 pages, 5726 KiB  
Review
A Comprehensive Review of Distributed MPPT for Grid-Tied PV Systems at the Sub-Module Level
by Yousef Alharbi, Ahmed Darwish and Xiandong Ma
Energies 2023, 16(14), 5468; https://doi.org/10.3390/en16145468 - 19 Jul 2023
Cited by 7 | Viewed by 2823
Abstract
Energy crises and the growth of the energy demand have increased the interest in utilizing unconventional power sources. Thus, renewable energy sources have become a topic of interest to mitigate rising energy concerns and cope with increased electricity demand. With remarkable merits including [...] Read more.
Energy crises and the growth of the energy demand have increased the interest in utilizing unconventional power sources. Thus, renewable energy sources have become a topic of interest to mitigate rising energy concerns and cope with increased electricity demand. With remarkable merits including cleanness and abundance, photovoltaic (PV) solar energy systems are a key to solving these issues. The employed inverters should effectively utilize the maximum available power from the PV solar system and transfer this power to the utility grid without posing any further limitations. However, the unequal power generation of different PV systems caused by partial shading (PS) and other PV panel degradation factors leads to a reduction in generation capacity. One of the relatively new solutions to mitigate the mismatch concerns between the PV modules and sub-modules is to extract the maximum power of each sub-module individually. The main objective of this paper is to present a comprehensive review of such PV grid-connected inverters topologies associated with sub-module connection and control. It will classify the PV grid-tied inverters in accordance with the level where the maximum power point tracking (MPPT) system is implemented. A special focus has been placed on sub-module microinverters (MI) in terms of circuit topologies, conversion efficiency, and controller design. This paper provides a comprehensive analysis of employing the distributed MPPT (DMPPT) approach to maximize the power generation of PV systems by mitigating the mismatch issues inside the PV module. The circuit topology, PV system configuration, and MPPT algorithms used for applying DMPPT solutions in PV SMs are discussed in detail in this study. Full article
Show Figures

Figure 1

17 pages, 3638 KiB  
Article
Optimal Sizing of a Photovoltaic/Battery Energy Storage System to Supply Electric Substation Auxiliary Systems under Contingency
by Ailton Gonçalves, Gustavo O. Cavalcanti, Marcílio A. F. Feitosa, Roberto F. Dias Filho, Alex C. Pereira, Eduardo B. Jatobá, José Bione de Melo Filho, Manoel H. N. Marinho, Attilio Converti and Luis A. Gómez-Malagón
Energies 2023, 16(13), 5165; https://doi.org/10.3390/en16135165 - 5 Jul 2023
Cited by 4 | Viewed by 2244
Abstract
Electric substations (ESS) are important facilities that must operate even under contingency to guarantee the electrical system’s performance. To achieve this goal, the Brazilian national electricity system operator establishes that alternating current (AC) auxiliary systems of ESS must have, at least, two power [...] Read more.
Electric substations (ESS) are important facilities that must operate even under contingency to guarantee the electrical system’s performance. To achieve this goal, the Brazilian national electricity system operator establishes that alternating current (AC) auxiliary systems of ESS must have, at least, two power supplies, and in the case of failure of these sources, an emergency generator (EG) must at least supply energy to the essential loads. In order to improve the availability of auxiliary systems, a microgrid with other sources, such as photovoltaic (PV) systems and Battery Energy Storage Systems (BESS), can be an alternative. In this case, an economical optimization of the PV/BESS system must be addressed considering the costs associated with the installation and maintenance of equipment, and the gains from the credits generated by the photovoltaic system in the net metering scheme. In this paper, the size of the BESS system was determined to supply energy to the load of auxiliary systems of an ESS, as well as a PV system to achieve a null total cost. Furthermore, multi-objective optimization using the genetic algorithm technique was employed to optimize the size of the hybrid PV/BESS to minimize the investment cost and time when the demand was not met. Simulations under different scenarios of contingency were allowed to obtain the Pareto frontier for the optimal sizing of a PV/BESS system to supply energy to AC auxiliary systems in an ESS under contingency. Full article
Show Figures

Figure 1

22 pages, 4269 KiB  
Article
How to Enhance Energy Services in Informal Settlements? Qualitative Comparison of Renewable Energy Solutions
by Rebekka Besner, Kedar Mehta and Wilfried Zörner
Energies 2023, 16(12), 4687; https://doi.org/10.3390/en16124687 - 13 Jun 2023
Cited by 1 | Viewed by 2199
Abstract
More than half of the urban population of Sub-Saharan Africa lives in informal housing conditions. While urban areas are, in general, characterized by a high electrification rate, residents of informal settlements are still affected by energy poverty, the use of traditional energy sources [...] Read more.
More than half of the urban population of Sub-Saharan Africa lives in informal housing conditions. While urban areas are, in general, characterized by a high electrification rate, residents of informal settlements are still affected by energy poverty, the use of traditional energy sources and unreliable electricity supply. The aim of the study is to give an overview of different renewable-energy-based solutions which are able to improve local energy provision. These are Solar Home Systems, Mini-Grids, and Energy-Hubs. The technologies are compared to another option for improving energy supply, namely Grid Expansion. The analysis is based on 24 Key Performance Indicators, which can be classified into technical, economic, environmental, social, and political dimensions. The selection of indicators is based on the challenges prevalent in informal settlements that impede a comprehensive, sustainable energy supply. The literature-based indices are used to determine which of the four technologies is a suitable solution for minimizing the challenges prevailing in informal settlements. The resulting matrix provides a holistic comparison and serves as a decision aid in selecting the appropriate technology for future projects in informal settlements, depending on local conditions and the needs of the population. The results show that the Energy-Hub is a valid alternative for energy supply improvement in Informal Settlements. Full article
Show Figures

Figure 1

25 pages, 14664 KiB  
Article
Solar Electric Vehicles as Energy Sources in Disaster Zones: Physical and Social Factors
by Kenji Araki, Yasuyuki Ota, Anju Maeda, Minoru Kumano and Kensuke Nishioka
Energies 2023, 16(8), 3580; https://doi.org/10.3390/en16083580 - 20 Apr 2023
Cited by 6 | Viewed by 4275
Abstract
Electric vehicles (EVs) have the advantage of being resilient to natural disasters. However, users hesitate to donate electricity when they lose the chance to recharge at the utility. Solar electric vehicles (SEVs) save energy through vehicle-integrated photovoltaics (VIPV) and make it possible to [...] Read more.
Electric vehicles (EVs) have the advantage of being resilient to natural disasters. However, users hesitate to donate electricity when they lose the chance to recharge at the utility. Solar electric vehicles (SEVs) save energy through vehicle-integrated photovoltaics (VIPV) and make it possible to voluntarily donate excess energy, thus maintaining facility resilience. Given that the supply of solar energy to VIPV systems is not continuous and is difficult to forecast, the contribution of VIPV to the resilience of the larger energy system has been called into question. This is the first study in which the potential of VIPV to maintain utility resilience is investigated in the context of physical factors, such as irradiance, and social factors. The actual energy yield of a VIPV car was determined using an advanced 3D solar irradiation model under a nonuniform shading distribution, with validation from actual measures of solar irradiance on five orthogonal sides of the car body. The Monte Carlo method was used to model the complex factors in VIPV energy storage and energy donations under different scenarios. Depending on the climate, population density, and shading environment, the voluntary contribution of stored electricity in SEV is sufficient to provide disaster relief support. Full article
Show Figures

Figure 1

27 pages, 6733 KiB  
Article
Assessing the Economic Impact of Introducing Localised PV Solar Energy Generation and Energy Storage for Fleet Electrification
by Maria Nunez Munoz, Erica E. F. Ballantyne and David A. Stone
Energies 2023, 16(8), 3570; https://doi.org/10.3390/en16083570 - 20 Apr 2023
Cited by 1 | Viewed by 1549
Abstract
Greenhouse gas (GHG) emissions from the transport sector and their effect on air quality are now a major concern, and the electrification of road freight transport is seen as one potential solution. However, this presents a challenge with the increased electricity demand on [...] Read more.
Greenhouse gas (GHG) emissions from the transport sector and their effect on air quality are now a major concern, and the electrification of road freight transport is seen as one potential solution. However, this presents a challenge with the increased electricity demand on a depot’s grid connection, and increased costs if this has to be upgraded. This study seeks to evaluate the impact on costs of introducing solar (PV) panels and a Battery Energy Storage System (BESS) when a company electrifies its fleet, based on two different priorities. On one hand, avoiding the use of the grid at peak price periods at the expense of upgrading the power connection. On the other hand, avoiding any power connection upgrade at the expense of incurring excess capacity charges. These two priorities aim to represent real-life challenges that logistics and commercial companies are facing when it comes to fleet electrification. The choice of prioritising one over the other may be driven by operational requirements and/or technical constraints. For each approach, a different energy management algorithm is developed using MATLAB and Simulink. The results obtained suggest that there is more flexibility in cost reduction when the upgrade of the power connection is not an obstacle. If the upgrade of the power network is not an option, the installation of PV panels and a BESS must be implemented together with other strategies (i.e., smart charging) to make it an economic option. Full article
Show Figures

Figure 1

27 pages, 416 KiB  
Review
AI-Based Scheduling Models, Optimization, and Prediction for Hydropower Generation: Opportunities, Issues, and Future Directions
by Yoan Villeneuve, Sara Séguin and Abdellah Chehri
Energies 2023, 16(8), 3335; https://doi.org/10.3390/en16083335 - 9 Apr 2023
Cited by 11 | Viewed by 3314
Abstract
Hydropower is the most prevalent source of renewable energy production worldwide. As the global demand for robust and ecologically sustainable energy production increases, developing and enhancing the current energy production processes is essential. In the past decade, machine learning has contributed significantly to [...] Read more.
Hydropower is the most prevalent source of renewable energy production worldwide. As the global demand for robust and ecologically sustainable energy production increases, developing and enhancing the current energy production processes is essential. In the past decade, machine learning has contributed significantly to various fields, and hydropower is no exception. All three horizons of hydropower models could benefit from machine learning: short-term, medium-term, and long-term. Currently, dynamic programming is used in the majority of hydropower scheduling models. In this paper, we review the present state of the hydropower scheduling problem as well as the development of machine learning as a type of optimization problem and prediction tool. To the best of our knowledge, this is the first survey article that provides a comprehensive overview of machine learning and artificial intelligence applications in the hydroelectric power industry for scheduling, optimization, and prediction. Full article
Show Figures

Figure 1

24 pages, 3951 KiB  
Article
Learning from Other Community Renewable Energy Projects: Transnational Transfer of Multi-Functional Energy Gardens from the Netherlands to Germany
by Maria Rosaria Di Nucci, Michael Krug, Lucas Schwarz, Vincenzo Gatta and Erik Laes
Energies 2023, 16(7), 3270; https://doi.org/10.3390/en16073270 - 6 Apr 2023
Cited by 2 | Viewed by 3188
Abstract
Citizen energy in general and renewable energy communities (RECs) in particular are becoming key vehicles for decentralisation, but also for the democratisation of the energy system. These initiatives are now more diverse than ever and are likely to continue to act as incubators [...] Read more.
Citizen energy in general and renewable energy communities (RECs) in particular are becoming key vehicles for decentralisation, but also for the democratisation of the energy system. These initiatives are now more diverse than ever and are likely to continue to act as incubators for significant projects in the transition to a renewable energy system. Beside the legal, regulatory, and financial challenges, there are several socio-economic and regulatory barriers that hinder the implementation of community energy projects. For this reason, policy learning and the dissemination of good/best practices that are transferable also to other contexts are important. This is an aspect that has not yet attracted much investigation, and only a few studies have explored the importance of transfer activities for the implementation of REC initiatives and their motives. This article aimed to address this knowledge gap by focussing on the transfer processes of best practices initiated in a particular region and discusses how these can be adapted and transferred to other contexts. We analysed the transfer case of a community renewable energy initiative, the multifunctional energy gardens, from the Netherlands to the German federal State of Thuringia, and extracted lessons with an overall validity for the transferability of drivers and success factors. We show how examples from other contexts with similar enabling conditions can represent significant foundations on which to build an effective strategy and what framework conditions are necessary to enhance the uptake of pervasive community energy initiatives in regions with low community energy development. Full article
Show Figures

Figure 1

16 pages, 5181 KiB  
Article
Estimation Model of Agrivoltaic Systems Maximizing for Both Photovoltaic Electricity Generation and Agricultural Production
by Daisuke Yajima, Teruya Toyoda, Masaaki Kirimura, Kenji Araki, Yasuyuki Ota and Kensuke Nishioka
Energies 2023, 16(7), 3261; https://doi.org/10.3390/en16073261 - 5 Apr 2023
Cited by 4 | Viewed by 6247
Abstract
Climate change and increasing food demand are global issues that require immediate attention. The agrivoltaic system, which involves installing solar panels above farmland, can simultaneously solve climate and food issues. However, current systems tend to reduce agricultural production and delay the harvest period [...] Read more.
Climate change and increasing food demand are global issues that require immediate attention. The agrivoltaic system, which involves installing solar panels above farmland, can simultaneously solve climate and food issues. However, current systems tend to reduce agricultural production and delay the harvest period due to shading by the solar panels. A delayed harvest period impacts the income of farmers who wish to sell produce at specific times. Incorporating a model that calculates the amount of electricity generated by solar irradiation, this study establishes a model to estimate the correct start date of cultivation for solar panel covered crops to ensure the correct harvest date and determines the expected income of farmers by calculating agricultural production and power generation. Using taro cultivation in Miyazaki Prefecture as a case study, the model estimated that the start date of cultivation should be brought forward by 23 days to ensure the ideal harvest period and agricultural production. This would prevent an opportunity loss of USD 16,000 per year for a farm area of 10,000 m2. Furthermore, an additional income of USD 142,000 per year can be expected by adjusting shading rates for the cultivation and non-cultivation periods. Full article
Show Figures

Figure 1

17 pages, 2572 KiB  
Article
Barriers and Prospects for the Development of Renewable Energy Sources in Poland during the Energy Crisis
by Hubert Kryszk, Krystyna Kurowska, Renata Marks-Bielska, Stanisław Bielski and Bartłomiej Eźlakowski
Energies 2023, 16(4), 1724; https://doi.org/10.3390/en16041724 - 9 Feb 2023
Cited by 14 | Viewed by 3497
Abstract
Europe is currently facing the potentially biggest energy crisis in history. There are many reasons for this, and the current geopolitical situation makes it clear that we are being forced to take immediate action to ensure sufficient energy supplies to consumers. Until recently, [...] Read more.
Europe is currently facing the potentially biggest energy crisis in history. There are many reasons for this, and the current geopolitical situation makes it clear that we are being forced to take immediate action to ensure sufficient energy supplies to consumers. Until recently, the European Union was dependent on Russian energy resources (mainly oil and gas). For many years, the EU countries had been shutting down their own production and importing much cheaper raw material from Russia. The threat of a blackout is becoming increasingly possible. European governments are preparing businesses and households for the energy crisis in various ways, but there is also a great deal of mobilization to accelerate the development of renewable energy sources (RES). The aim of this study was to identify the barriers and prospects for RES development in Poland in the current geopolitical conditions. The reasons for insufficient grid HC were analyzed. Additionally, the article aimed to assess the prospects for solar energy development in Poland. Wind power was discussed only in general terms because the development of wind farms is inhibited by the regulatory framework. Particular attention was paid to hosting capacity (HC) and the condition of the power infrastructure as the main determinants of RES development in Poland. Numerous documents developed by power companies and government agencies responsible for implementing and managing energy in Poland were analyzed. Special attention was paid to legal regulations and the need for legislative changes. As a country, Poland has one of the highest growth rates in photovoltaic (PV) installations. The forecasts for increasing HC, as a prerequisite for RES development in Poland, are not promising. Full article
Show Figures

Figure 1

16 pages, 7339 KiB  
Article
A Novel Approach Using High Charging Voltage for the Restoration of Discarded Lead Acid Batteries
by Chee Hiun Lee, Jianhui Wong and Yun Seng Lim
Energies 2023, 16(4), 1598; https://doi.org/10.3390/en16041598 - 5 Feb 2023
Cited by 1 | Viewed by 3129
Abstract
A lead acid battery is an old renewable battery that is usually discharged to deliver a high surge current to ignite a petrol-based engine. Nowadays, there are different improved versions of lead acid batteries that can deliver high energy densities with low maintenance [...] Read more.
A lead acid battery is an old renewable battery that is usually discharged to deliver a high surge current to ignite a petrol-based engine. Nowadays, there are different improved versions of lead acid batteries that can deliver high energy densities with low maintenance costs. As the batteries are charged and discharged repeatedly over time, the amount of lead sulfate across the electrode plates grows, reducing the total surface areas of the plates and, thus, the rate of ionization between the electrolyte and the plate surfaces. The batteries then eventually come to the end of their service lives. Even with the improved versions, lead acid batteries are usually discarded at their retirement. However, if the retired batteries can be used for other purposes, the circular economy of the batteries can be improved significantly. It is therefore necessary to study the physical characteristics of the retired batteries and explore means of improving their charging and discharging capabilities. This paper presents research on improving the storage capability of retired lead acid batteries by applying different charging voltages across them. The results show that the electrode plates of the retired batteries become porous when a high charging voltage is applied, hence increasing the total surface area of the plate surfaces. The storage capability of the batteries is improved because the accumulated lead sulfate is removed from the electrode plates by the high charging voltage. As a result, the rate of ionization is increased, hence restoring the storing capability of the retired batteries to up to 71–89% of the original capacity rating. Full article
Show Figures

Graphical abstract

12 pages, 2236 KiB  
Article
Estimating the Operating Reserve Demand Curve for Efficient Adoption of Renewable Sources in Korea
by Wooyoung Jeon and Jungyoun Mo
Energies 2023, 16(3), 1426; https://doi.org/10.3390/en16031426 - 1 Feb 2023
Cited by 1 | Viewed by 1559
Abstract
As the proportions of variable renewable sources (VRSs) such as solar and wind energy increase rapidly in the power system, their uncertainties inevitably undermine power supply reliability and increase the amount of operating reserve resources required to manage the system. However, because operating [...] Read more.
As the proportions of variable renewable sources (VRSs) such as solar and wind energy increase rapidly in the power system, their uncertainties inevitably undermine power supply reliability and increase the amount of operating reserve resources required to manage the system. However, because operating reserves have the characteristics of a public good and their value is related to the social cost of blackouts, it is difficult to determine their market price efficiently, which leads to inefficiencies in procuring operating reserves. This study estimates the operating reserve demand curve (ORDC) of the Korean power system to provide an effective basis for measuring the proper value and quantity of operating reserves needed to meet the reliability standard. A stochastic dynamic optimization model is applied to incorporate the probabilistic characteristics of VRS and the inter-hour constraint, which is necessary for analyzing load-following reserves. An econometric model and the Monte Carlo simulation method are used to generate the forecast profiles of solar and wind generation. The results indicate that the proper amount of hourly operating reserves needed in 2034 is approximately 4.4 times higher than that in 2020 at the current reserve offer price. The ORDC of 2020 has a price-inelastic shape, whereas the ORDC of 2034 has a price-elastic shape because the reserve requirement varies considerably with its offer price level in the high-VRS penetration case. This variability is due to alternatives, such as VRS curtailment or load shedding, which can replace the reserve requirement. This study also showed that VRS curtailment is an effective balancing resource as an alternative to reserves. Full article
Show Figures

Figure 1

21 pages, 1535 KiB  
Article
Electricity Production and Sustainable Development: The Role of Renewable Energy Sources and Specific Socioeconomic Factors
by George E. Halkos and Apostolos S. Tsirivis
Energies 2023, 16(2), 721; https://doi.org/10.3390/en16020721 - 7 Jan 2023
Cited by 18 | Viewed by 3586
Abstract
An eco-friendly and sustainable power production system constitutes the cornerstone of every country’s strategic plan to tackle climate change and enhance energy resource autonomy. Carbon dioxide abatement in electricity generation, in addition to being a necessary condition for t “green” energy transition, can [...] Read more.
An eco-friendly and sustainable power production system constitutes the cornerstone of every country’s strategic plan to tackle climate change and enhance energy resource autonomy. Carbon dioxide abatement in electricity generation, in addition to being a necessary condition for t “green” energy transition, can contribute greatly to cleaner industrial production and sustainable development. Emphasizing this key role of the power sector, the present research focuses on shedding light on the impact of renewable energy resources (RES), per capita gross domestic product (GDP), electricity gross fixed capital formation (GFCF) and urbanization in the CO2 intensity, and the sustainability level of electricity production. The analysis is based on a comprehensive dataset of 31 countries including 26 European countries, U.S.A., Japan, Australia, Canada, and New Zealand from 1995 until 2018. The econometric outcomes revealed the strong statistical significance of all variables and a plethora of causality relationships, upon which several policy suggestions are made. Interestingly, GDP per capita beyond a certain level can gradually become an aggravating factor for the electricity carbon footprint. Similarly, the vital role of RES in clean electricity production was confirmed as expected, yet surprisingly, this effect also appears to reverse after a certain percentage of total RES reliance. In contrast to urbanization, the electricity GFCF parameter is estimated to have an adverse effect on electricity CO2 intensity, indicating that the vast amount of new investments in the power sector concerns carbon-intensive technologies. Finally, a dynamic analysis is carried out, revealing to policy makers the necessary time frame after which the implementation of new energy policies can have the full impact on the carbon emissions of electricity generation. Full article
Show Figures

Figure 1

25 pages, 12223 KiB  
Article
Demand Response with Electrical Heating in Detached Houses in Finland and Comparison with BESS for Increasing PV Self-Consumption
by Juha Koskela and Pertti Järventausta
Energies 2023, 16(1), 497; https://doi.org/10.3390/en16010497 - 2 Jan 2023
Cited by 5 | Viewed by 1847
Abstract
Distributed electric power production by small-scale customers is increasing continuously. Photovoltaic production is a popular method of producing self-energy for customers. Additionally, power systems require more flexibility when weather-dependent renewable energy production increases. Small-scale customers can increase the self-consumption of self-produced energy by [...] Read more.
Distributed electric power production by small-scale customers is increasing continuously. Photovoltaic production is a popular method of producing self-energy for customers. Additionally, power systems require more flexibility when weather-dependent renewable energy production increases. Small-scale customers can increase the self-consumption of self-produced energy by using batteries or a demand response operation. However, batteries require high investment, and demand response operations induce a loss of comfort. Customers who heat their buildings using electric heaters are a good target for demand response operations because their heating can be controlled with limited changes in the indoor temperature. The demand response potential of a building can be defined by simply using customer load profiles and knowledge of the outdoor temperature. Any other information is not required in the proposed novel method. A tolerable variation in indoor temperature corresponds to considerably smaller battery capacity, though it is still a significant amount. With an optimally sized photovoltaic system, it is possible to use both methods simultaneously to increase self-consumption. Maximal benefits can be attained from both methods if the battery system is used as a primary control and the demand response is used as a secondary control. The defined novel method for determining the demand response potential of small-scale customers can also be used when estimating the flexibility of a large customer group. Small-scale customers together can provide significant flexible capacity when their electrical heating is centrally controlled. Full article
Show Figures

Figure 1

2022

Jump to: 2024, 2023, 2021, 2020

22 pages, 3904 KiB  
Article
Optimal Design and Comparative Analysis of a PV/Mini-Hydropower and a PV/Battery Used for Electricity and Water Supply
by Ruben Zieba Falama, Wojciech Skarka and Serge Yamigno Doka
Energies 2023, 16(1), 307; https://doi.org/10.3390/en16010307 - 27 Dec 2022
Cited by 5 | Viewed by 2502
Abstract
This work proposed an optimal design of PV-system-based water-pumped energy storage for both electricity and water supply. A case study was considered in a rural community in Cameroon. The parameters of the assessment of the system were reliability, represented in the present work [...] Read more.
This work proposed an optimal design of PV-system-based water-pumped energy storage for both electricity and water supply. A case study was considered in a rural community in Cameroon. The parameters of the assessment of the system were reliability, represented in the present work by the system supply deficiency (SSD), and economic accessibility, represented by the levelized cost of energy (LCOE). The obtained results showed that for 0% SSD, the optimal configuration of the system was composed of 438 PV modules of 235 W, an immersed solar motor pump of 35 kW, a hydroelectric turbine of 51.7 kW, an upper reservoir of 2307.1 m3, an inverter of 25.27 kW, and a total dynamic head of 88 m. The corresponding LCOE to this configuration is 0.224 USD/kWh. The economic accessibility of the designed system was evaluated by comparison with a PV-system-based battery energy storage. The optimal design configuration of the studied PV-system-based battery energy storage was a PV generator (120 PV modules of 235 W), solar motor pump (15 kW), upper reservoir (590.4 m3), battery capacity (351.78 kWh), inverter (25.27 kW), and total dynamic head (81 m). The corresponding LCOE to this configuration was 0.1857 USD/kWh. Although the PV-system-based battery storage appeared to be economically more cost-effective than the PV-system-based water-pumped energy storage, the sensitivity analysis revealed that there was the possibility for the PV-system-based water-pumped energy storage to be economically more profitable than the PV-system-based battery energy storage. This economic outperformance occurred when the project lifetime was a multiple of 7.5 years or when the costs of the storage components were reduced from 20% to 60%. Full article
Show Figures

Figure 1

24 pages, 5778 KiB  
Article
Solar Energy Powered Decentralized Smart-Grid for Sustainable Energy Supply in Low-Income Countries: Analysis Considering Climate Change Influences in Togo
by Kokou Amega, Yendoubé Laré, Ramchandra Bhandari, Yacouba Moumouni, Aklesso Y. G. Egbendewe, Windmanagda Sawadogo and Saidou Madougou
Energies 2022, 15(24), 9532; https://doi.org/10.3390/en15249532 - 15 Dec 2022
Cited by 2 | Viewed by 2225
Abstract
A smart and decentralized electrical system, powered by grid-connected renewable energy (RE) with a reliable storage system, has the potential to change the future socio-economic dynamics. Climate change may, however, affect the potential of RE and its related technologies. This study investigated the [...] Read more.
A smart and decentralized electrical system, powered by grid-connected renewable energy (RE) with a reliable storage system, has the potential to change the future socio-economic dynamics. Climate change may, however, affect the potential of RE and its related technologies. This study investigated the impact of climate change on photovoltaic cells’ temperature response and energy potential under two CO2 emission scenarios, RCP2.6 and 8.5, for the near future (2024–2040) and mid-century (2041–2065) in Togo. An integrated Regional Climate Model version 4 (RegCM4) from the CORDEX-CORE initiative datasets has been used as input. The latter platform recorded various weather variables, such as solar irradiance, air temperature, wind speed and direction, and relative humidity. Results showed that PV cells’ temperature would likely rise over all five regions in the country and may trigger a decline in the PV potential under RCP2.6 and 8.5. However, the magnitude of the induced change, caused by the changing climate, depended on two major factors: (1) the PV technology and (2) geographical position. Results also revealed that these dissimilarities were more pronounced under RCP8.5 with the amorphous technology. It was further found that, nationally, the average cell temperature would have risen by 1 °C and 1.82 °C under RCP2.6 and 8.5, in that order, during the 2024–2065 period for a-Si technology. Finally, the PV potential would likely decrease, on average, by 0.23% for RCP2.6 and 0.4% for RCP8.5 for a-Si technology. Full article
Show Figures

Figure 1

21 pages, 1903 KiB  
Article
Levelling the Photovoltaic Power Profile with the Integrated Energy Storage System
by Alberto Benato, Francesco De Vanna and Anna Stoppato
Energies 2022, 15(24), 9521; https://doi.org/10.3390/en15249521 - 15 Dec 2022
Cited by 4 | Viewed by 1594
Abstract
The extensive penetration in the energy mix of variable renewable energy sources, such as wind and solar, guarantees boosting of the transition toward a decarbonized and sustainable energy system as well as tackling of climate targets. However, the instability and unpredictability of such [...] Read more.
The extensive penetration in the energy mix of variable renewable energy sources, such as wind and solar, guarantees boosting of the transition toward a decarbonized and sustainable energy system as well as tackling of climate targets. However, the instability and unpredictability of such sources predominantly affect their plant production. Thus, utility-scale energy storage is required to aid in balancing supply and demand and, as a result, to prevent unbalances that might cause issues at different grid levels. In the present study, the authors’ patented energy storage technology, known as Integrated Energy Storage System (I-ESS), is combined with a 10 MWp solar plant. The PV plant and the I-ESS unit function as a Virtual Power Plant (VPP). The selected VPP management strategy attempts to optimize the daily hours during which the plant supplies steady power output. Numerical simulations show that the VPP plant can effectively smooth the PV peak and manage the power supply. In particular, by the definition of a novel metric expressing the ratio between regular hours of power provided to the grid plus the energy stored in the backup unit and the total number of hours in a year, the results show that the VPP regularity is relatively high in terms of PV output, ranging from a low of 50% in December to a high of 87% in August. Thus, the proposed VPP arrangement seems to be a promising technology for pushing toward the carbon-neutral transition. Full article
Show Figures

Figure 1

26 pages, 4171 KiB  
Review
Vanadium Oxide–Conducting Polymers Composite Cathodes for Aqueous Zinc-Ion Batteries: Interfacial Design and Enhancement of Electrochemical Performance
by Elena G. Tolstopyatova, Mikhail A. Kamenskii and Veniamin V. Kondratiev
Energies 2022, 15(23), 8966; https://doi.org/10.3390/en15238966 - 27 Nov 2022
Cited by 8 | Viewed by 2402
Abstract
Aqueous zinc-ion batteries (AZIBs) are being intensively developed as potential alternative electrochemical power sources, due to their advantages such as low cost, high safety, abundance of natural zinc resources and appropriate energy density. Among currently investigated prospective cathode materials for AZIBs, vanadium oxide-based [...] Read more.
Aqueous zinc-ion batteries (AZIBs) are being intensively developed as potential alternative electrochemical power sources, due to their advantages such as low cost, high safety, abundance of natural zinc resources and appropriate energy density. Among currently investigated prospective cathode materials for AZIBs, vanadium oxide-based composites with intrinsically conducting polymers have shown many advantages, such as high capacity, high power density and long battery life. This review gives a focused view of the design for the boosting of zinc ion storage performance using intrinsically conducting polymers in vanadium oxide-based composites and the mechanism of intercalation processes. The main challenges in interfacial engineering of vanadium oxide-conducting polymers composite structures and the prospects for further development of such cathode materials are summarized and discussed. The review would give rise to a broad interest focusing on the advantageous strategy of the development of vanadium oxide composite cathodes with intrinsically conducting polymers (polyaniline, polypyrrole, poly(3,4-ethylenedioxythiophene)) for AZIBs with improved energy density, high-rate capability and stability. Full article
Show Figures

Figure 1

21 pages, 2603 KiB  
Article
Optimizing Current Profiles for Efficient Online Estimation of Battery Equivalent Circuit Model Parameters Based on Cramer–Rao Lower Bound
by Prarthana Pillai, Sneha Sundaresan, Krishna R. Pattipati and Balakumar Balasingam
Energies 2022, 15(22), 8441; https://doi.org/10.3390/en15228441 - 11 Nov 2022
Cited by 5 | Viewed by 1770
Abstract
Battery management systems (BMS) are important for ensuring the safety, efficiency and reliability of a battery pack. Estimating the internal equivalent circuit model (ECM) parameters of a battery, such as the internal open circuit voltage, battery resistance and relaxation parameters, is a crucial [...] Read more.
Battery management systems (BMS) are important for ensuring the safety, efficiency and reliability of a battery pack. Estimating the internal equivalent circuit model (ECM) parameters of a battery, such as the internal open circuit voltage, battery resistance and relaxation parameters, is a crucial requirement in BMSs. Numerous approaches to estimating ECM parameters have been reported in the literature. However, existing approaches consider ECM identification as a joint estimation problem that estimates the state of charge together with the ECM parameters. In this paper, an approach is presented to decouple the problem into ECM identification alone. Using the proposed approach, the internal open circuit voltage and the ECM parameters can be estimated without requiring the knowledge of the state of charge of the battery. The proposed approach is applied to estimate the open circuit voltage and internal resistance of a battery. Full article
Show Figures

Figure 1

35 pages, 32554 KiB  
Article
Experimental Validation of an Enhanced MPPT Algorithm and an Optimal DC–DC Converter Design Powered by Metaheuristic Optimization for PV Systems
by Efrain Mendez-Flores, Alexandro Ortiz, Israel Macias and Arturo Molina
Energies 2022, 15(21), 8043; https://doi.org/10.3390/en15218043 - 29 Oct 2022
Cited by 10 | Viewed by 1946
Abstract
Nowadays, photovoltaic (PV) systems are responsible for over 994 TWH of the worldwide energy supply, which highlights their relevance and also explains why so much research has arisen to enhance their implementation; among this research, different optimization techniques have been widely studied to [...] Read more.
Nowadays, photovoltaic (PV) systems are responsible for over 994 TWH of the worldwide energy supply, which highlights their relevance and also explains why so much research has arisen to enhance their implementation; among this research, different optimization techniques have been widely studied to maximize the energy harvested under different environmental conditions (maximum power point tracking) and to optimize the efficiency of the required power electronics for the implementation of MPPT algorithms. On the one hand, an earthquake optimization algorithm (EA) was introduced as a multi-objective optimization tool for DC–DC converter design, mostly to overcome component shortages by optimal replacement, but it had never been tested (until now) for PV applications. On the other hand, the original EA was also taken as inspiration for a promising EA-based MPPT, which presumably enabled a solution with simple parametric calibration and improved dynamic behavior; yet prior to this research, the EA-MPPT had never been experimentally validated. Hence, this work fills the gap and provides the first implementation of the EA-based MPPT, validating its performance and suitability under real physical conditions, where the experimental testbed was optimized through the EA design methodology for DC–DC converters and implemented for the first time for PV applications. The results present energy waste reduction between 12 and 36% compared to MPPTs based on perturb and observe and particle swarm optimization; meanwhile, the designed converter achieved 7.3% current ripple, which is between 2.7 and 12.7% less than some industrial converters, and it had almost 90% efficiency at nominal operation. Finally, the EA-MPPT proved simple enough to be implemented even through an 8-bit MCU (ATmega328P from Arduino UNO). Full article
Show Figures

Figure 1

17 pages, 7060 KiB  
Article
A Thermal Model to Estimate PV Electrical Power and Temperature Profile along Panel Thickness
by Francesco Nicoletti, Mario Antonio Cucumo, Vittorio Ferraro, Dimitrios Kaliakatsos and Albino Gigliotti
Energies 2022, 15(20), 7577; https://doi.org/10.3390/en15207577 - 14 Oct 2022
Cited by 8 | Viewed by 2048
Abstract
The production of electricity from photovoltaic panels has experienced significant developments. To manage the energy flows introduced into the electricity grid, it is necessary to estimate the productivity of PV panels under the climatic conditions. In this study, a photovoltaic panel is modelled [...] Read more.
The production of electricity from photovoltaic panels has experienced significant developments. To manage the energy flows introduced into the electricity grid, it is necessary to estimate the productivity of PV panels under the climatic conditions. In this study, a photovoltaic panel is modelled from thermal and electrical points of view to evaluate electrical performance and identify the temperature distribution in the layers. The analysis performed is time dependent and the problem is solved using the finite difference technique. A methodology is introduced to estimate the cloudiness of the sky, which affects radiative heat exchange. The calculation method is validated using experimental data recorded in a laboratory of the University of Calabria. Temperature and electrical power are predicted with RMSE of 1.5–2.0 °C and NRMSE of 1.2–2.1%, respectively. The evaluation of the temperature profile inside the panel is essential to understand how heat is dissipated. The results show that the top surface (glass) is almost always colder than the back of the panel, despite being exposed to radiation. In addition, the upper surface dissipates more heat power than the lower one. Cooling systems, such as spray cooling, work better if they are installed on the back of the panel. Full article
Show Figures

Figure 1

16 pages, 873 KiB  
Article
Selected Characteristics of Municipalities as Determinants of Enactment in Municipal Spatial Plans for Renewable Energy Sources—The Case of Poland
by Małgorzata Blaszke, Iwona Foryś, Maciej J. Nowak and Bartosz Mickiewicz
Energies 2022, 15(19), 7274; https://doi.org/10.3390/en15197274 - 3 Oct 2022
Cited by 4 | Viewed by 1415
Abstract
The article proposes methods by which an in-depth analysis of the factors determining the planning activity of municipalities for renewable energy sources can be carried out. The article aims to determine the relationship between the number of local spatial plans specifying designation for [...] Read more.
The article proposes methods by which an in-depth analysis of the factors determining the planning activity of municipalities for renewable energy sources can be carried out. The article aims to determine the relationship between the number of local spatial plans specifying designation for renewable energy sources and the municipality’s area, population and planning situation. All local spatial plans in Poland (a total of 104,720 plans) were analysed, distinguishing in each municipality the number of plans with designation for renewable energy sources and micro-installations (a total of 11,338 plans). Then, using quantitative methods, this data was matched with data on the municipalities’ population, area, and planning activity. At the same time, the article provides a literature review of the critical problems concerning the relationship between investments in renewable energy sources and local planning. The barriers encountered are transnational in nature. The discussion section indicates how the proposed research methods can address identified barriers. Further possible research directions are also identified. The study shows a correlation between the planning activity of municipalities in the field of renewable energy sources and both population and population density. The higher the population density (highly urbanised areas), the higher the planning activity as well, and with it, the associated planning activity for renewable energy sources. The results in this respect are spatially differentiated. The main contribution of the research is to identify the relationship between the spatial and demographic characteristics of the municipalities and the way spatial plans are approached. This research identifies how local spatial policies toward renewable energy sources can be assessed. Full article
Show Figures

Figure 1

30 pages, 7936 KiB  
Article
Utilization of Basalt Dust as Waste Material in Cement Grouts for Geothermal Application
by Krzysztof Seńczuk, Aneta Sapińska-Śliwa and Tomasz Kowalski
Energies 2022, 15(19), 7033; https://doi.org/10.3390/en15197033 - 25 Sep 2022
Cited by 1 | Viewed by 1894
Abstract
Research on the utilization of the Earth’s heat focuses mainly on effective sourcing of energy accumulated in rock mass. One of the most important parameters is thermal conductivity, which can be modified using various compositions of cement grouts. Hardened cement slurry is intended [...] Read more.
Research on the utilization of the Earth’s heat focuses mainly on effective sourcing of energy accumulated in rock mass. One of the most important parameters is thermal conductivity, which can be modified using various compositions of cement grouts. Hardened cement slurry is intended to improve thermal conductivity. It should function as a sort of extension of the rock mass to the outer diameter of heat exchanger tubes. Regardless of the thermal conductivity of the rock, high conductivity of the grout increases the energy efficiency of the BHE. Heat accumulated in the rock mass can be extracted using borehole heat exchangers (BHE), in which high thermal conductivity of cement slurry is wanted over the entire length of the exchanger. Generally, in case of deep borehole heat exchangers (DBHE), it is recommended to use two types of cement slurry, one with reduced thermal conductivity in the upper part of the exchanger and grout with increased thermal conductivity in its lower part. When cementing geothermal wells, cement grout with decreased thermal conductivity along the entire length of the borehole is most commonly used. Geothermal boreholes extract geothermal water which, at the surface, is used for heating, for example. Then, after use, the cooled water is injected through injection holes. In this article, two different basalt dusts are examined. These dusts were obtained by crushing basalt boulders in open-pit mines. They were examined for their effect on thermal conductivity when added to grout. According to the Polish Ordinance of the Minister of Environment dated 9 December 2014 regarding the waste catalogue, they were classified as waste. The materials, named basalt dust A and basalt dust B, were used to create cement slurries with a water–cement ratio of 0.5–0.7 with a wide range of percentage concentration of basalt dust. The test results show that as concentrations in the slurry increase, the values of thermal conductivity and strength decrease. This correlation occurred for both tested additives. Full article
Show Figures

Figure 1

25 pages, 3270 KiB  
Review
Open-Circuit Voltage Models for Battery Management Systems: A Review
by Prarthana Pillai, Sneha Sundaresan, Pradeep Kumar, Krishna R. Pattipati and Balakumar Balasingam
Energies 2022, 15(18), 6803; https://doi.org/10.3390/en15186803 - 17 Sep 2022
Cited by 44 | Viewed by 5272
Abstract
A battery management system (BMS) plays a crucial role to ensure the safety, efficiency, and reliability of a rechargeable Li-ion battery pack. State of charge (SOC) estimation is an important operation within a BMS. Estimated SOC is required in several BMS operations, such [...] Read more.
A battery management system (BMS) plays a crucial role to ensure the safety, efficiency, and reliability of a rechargeable Li-ion battery pack. State of charge (SOC) estimation is an important operation within a BMS. Estimated SOC is required in several BMS operations, such as remaining power and mileage estimation, battery capacity estimation, charge termination, and cell balancing. The open-circuit voltage (OCV) look-up-based SOC estimation approach is widely used in battery management systems. For OCV lookup, the OCV–SOC characteristic is empirically measured and parameterized a priori. The literature shows numerous OCV–SOC models and approaches to characterize them and use them in SOC estimation. However, the selection of an OCV–SOC model must consider several factors: (i) Modeling errors due to approximations, age/temperature effects, and cell-to-cell variations; (ii) Likelihood and severity of errors when the OCV–SOC parameters are rounded; (iii) Computing system requirements to store and process OCV parameters; and (iv) The required computational complexity of real-time OCV lookup algorithms. This paper presents a review of existing OCV–SOC models and proposes a systematic approach to select a suitable OCV–SOC for implementation based on various constraints faced by a BMS designer in practical application. Full article
Show Figures

Figure 1

35 pages, 5464 KiB  
Review
Novel Trends in Proton Exchange Membrane Fuel Cells
by Abdul Ghani Olabi, Tabbi Wilberforce, Abdulrahman Alanazi, Parag Vichare, Enas Taha Sayed, Hussein M. Maghrabie, Khaled Elsaid and Mohammad Ali Abdelkareem
Energies 2022, 15(14), 4949; https://doi.org/10.3390/en15144949 - 6 Jul 2022
Cited by 22 | Viewed by 7040
Abstract
Fuel cells (FCs) have received huge attention for development from lab and pilot scales to full commercial scale. This is mainly due to their inherent advantage of direct conversion of chemical energy to electrical energy as a high-quality energy supply and, hence, higher [...] Read more.
Fuel cells (FCs) have received huge attention for development from lab and pilot scales to full commercial scale. This is mainly due to their inherent advantage of direct conversion of chemical energy to electrical energy as a high-quality energy supply and, hence, higher conversion efficiency. Additionally, FCs have been produced at a wide range of capacities with high flexibility due to modularity characteristics. Using the right materials and efficient manufacturing processes is directly proportional to the total production cost. This work explored the different components of proton exchange membrane fuel cells (PEMFCs) and their manufacturing processes. The challenges associated with these manufacturing processes were critically analyzed, and possible mitigation strategies were proposed. The PEMFC is a relatively new and developing technology so there is a need for a thorough analysis to comprehend the current state of fuel cell operational characteristics and discover new areas for development. It is hoped that the view discussed in this paper will be a means for improved fuel cell development. Full article
Show Figures

Figure 1

18 pages, 5101 KiB  
Article
Impact of Solar Inverter Dynamics during Grid Restoration Period on Protection Schemes Based on Negative-Sequence Components
by Almir Ekic, Di Wu and John N. Jiang
Energies 2022, 15(12), 4360; https://doi.org/10.3390/en15124360 - 15 Jun 2022
Cited by 2 | Viewed by 2255
Abstract
The growing penetration of renewable resources such as wind and solar into the electric power grid through power electronic inverters is challenging grid protection. Due to the advanced inverter control algorithms, the inverter-based resources present fault responses different from conventional generators, which can [...] Read more.
The growing penetration of renewable resources such as wind and solar into the electric power grid through power electronic inverters is challenging grid protection. Due to the advanced inverter control algorithms, the inverter-based resources present fault responses different from conventional generators, which can fundamentally affect the way that the power grid is protected. This paper studied solar inverter dynamics focused on negative-sequence quantities during the restoration period following a grid disturbance by using a real-time digital simulator. It was found that solar inverters can act as negative-sequence sources to inject negative-sequence currents into the grid during the restoration period. The negative-sequence current can be affected by different operating conditions such as the number of inverters in service, grid strength, and grid fault types. Such negative-sequence responses can adversely impact the performance of protection schemes based on negative-sequence components and potentially cause relay maloperations during the grid restoration period, thus making system protection less secure and reliable. Full article
Show Figures

Figure 1

13 pages, 7230 KiB  
Article
Control Strategies Applied to a Heat Transfer Loop of a Linear Fresnel Collector
by Alaric Christian Montenon and Rowida Meligy
Energies 2022, 15(9), 3338; https://doi.org/10.3390/en15093338 - 4 May 2022
Cited by 6 | Viewed by 1973
Abstract
The modelling of Linear Fresnel Collectors (LFCs) is crucial in order to predict accurate performance for annual yields and to define proper commands to design the suitable controller. The ISO 9806 modelling, applied to thermal collectors, presents some gaps especially with concentration collectors [...] Read more.
The modelling of Linear Fresnel Collectors (LFCs) is crucial in order to predict accurate performance for annual yields and to define proper commands to design the suitable controller. The ISO 9806 modelling, applied to thermal collectors, presents some gaps especially with concentration collectors including LFCs notably due to the factorisation of the incidence angle modifiers and the fact that they are considered symmetric around the south meridian. The present work details the use of two alternative modellings methodologies based on recorded experimental data on the solar system installed at the Cyprus Institute, in the outskirts of Nicosia, Cyprus. The first modelling is the RealTrackEff, which is an improved ISO9806 modelling, and the second is constructed using the CARNOT blockset in MATLAB/Simulink. Both models include all the elements of the heat transfer fluid loop, i.e., mineral oil, with a tank and a heat-exchanger. First, the open loop’s studies demonstrated that the root mean square on temperature is 1 °C with the RealTrackEff; 2.9 °C with the CARNOT and 6.3 °C with the ISO9806 in comparison to the experimental data. Then, a PID control is applied on the experimental values in order to estimate the impact on the outlet temperature on the absorber and on power generation. Results showed that the error on the estimation of the heat absorbed reaches 32%. Full article
Show Figures

Figure 1

15 pages, 1155 KiB  
Article
Optimization of Solar/Fuel Cell Hybrid Energy System Using the Combinatorial Dynamic Encoding Algorithm for Searches (cDEAS)
by Jong-Wook Kim, Heungju Ahn, Hyeon Cheol Seo and Sang Cheol Lee
Energies 2022, 15(8), 2779; https://doi.org/10.3390/en15082779 - 10 Apr 2022
Cited by 6 | Viewed by 2054
Abstract
This study proposes a computational design method for determining a hybrid power system’s sizing and ratio values that combines the national electric, solar cell, and fuel cell power sources. The inequality constraints associated with the ranges of power storage exchange and the stored [...] Read more.
This study proposes a computational design method for determining a hybrid power system’s sizing and ratio values that combines the national electric, solar cell, and fuel cell power sources. The inequality constraints associated with the ranges of power storage exchange and the stored energy are reflected as penalty functions in the overall cost function to be minimized. Using the energy hub model and the actual data for the solar cell power and the load of the residential sector in one Korean city for one hundred days, we optimize the ratio of fuel cell energy and solar cell energy to 0.46:0.54 through our proposed approach. We achieve an average cost-reduction effect of 19.35% compared to the cases in which the fuel-cell energy ratio is set from 0.1 to 0.9 in 0.1 steps. To optimize the sizing and the ratio of fuel-cell energy in the hybrid power system, we propose the modified version of the univariate dynamic encoding algorithm for searches (uDEAS) as a novel optimization method. The proposed novel approaches can be applied directly to any place to optimize an energy hub system model comprising three power sources, i.e., solar power, fuel cell, and power utility. Full article
Show Figures

Figure 1

22 pages, 89063 KiB  
Article
Energy Cell Simulation for Sector Coupling with Power-to-Methane: A Case Study in Lower Bavaria
by Robert Bauer, Dominik Schopf, Grégoire Klaus, Raimund Brotsack and Javier Valdes
Energies 2022, 15(7), 2640; https://doi.org/10.3390/en15072640 - 4 Apr 2022
Cited by 3 | Viewed by 2382
Abstract
In this study, the possibility of sector coupling with biological Power-to-Methane to support and stabilize the energy transition of the three major sectors of electricity, heat, and gas was addressed. For this purpose, the energy cell simulation methodology and the Calliope tool were [...] Read more.
In this study, the possibility of sector coupling with biological Power-to-Methane to support and stabilize the energy transition of the three major sectors of electricity, heat, and gas was addressed. For this purpose, the energy cell simulation methodology and the Calliope tool were utilized for energy system optimization. This combination provides detailed insights into the existing dependencies of consumers and fossil and renewable energy suppliers on a local scale. In this context, Power-to-Methane represents an efficient technology for quickly and effectively exploiting unused electricity potential for various sectors and consumers. It was found that, even in regions with low wind levels, this surplus electricity potential already exists and depends on various influencing factors in very different ways. The solar influence on these potentials was considered in connection with gas-fired cogeneration plants for district heating. It was found that the current heat demand for district heating produces a large amount of electricity and can generate surplus electricity in the winter. However, in the summer, large amounts of usable waste heat are dissipated into the environment, owing to the low consumption of district heat. This problem in the heat sector could be reduced by the expansion of photovoltaics, but this would require further expansion of storage or conversion systems in the electricity sector. This demonstrates that the consideration of several sectors is necessary to reflect the complexity of the sector coupling with Power-to-Methane properly. Full article
Show Figures

Figure 1

40 pages, 6078 KiB  
Review
Optimization Models under Uncertainty in Distributed Generation Systems: A Review
by Àlex Alonso-Travesset, Helena Martín, Sergio Coronas and Jordi de la Hoz
Energies 2022, 15(5), 1932; https://doi.org/10.3390/en15051932 - 7 Mar 2022
Cited by 14 | Viewed by 3638
Abstract
Distributed generation systems (DGSs) are one of the key developments enabling the energy transition. DGSs provide users with increased control over their energy use and generation, but entail greater complexity in their design and operation. Traditionally, optimization models have been used to overcome [...] Read more.
Distributed generation systems (DGSs) are one of the key developments enabling the energy transition. DGSs provide users with increased control over their energy use and generation, but entail greater complexity in their design and operation. Traditionally, optimization models have been used to overcome this complexity, and currently, research is focusing on integrating uncertainties on them. This review attempts to analyze, classify and discuss 170 articles dealing with optimization of DGSs under uncertainty. A survey has been performed to identify the selected manuscripts and the strengths and weaknesses of previous reviews. As a result, an innovative classification has been designed and the distinct elements of optimization models in DGSs have been highlighted: microgrid architecture, sources of uncertainty, uncertainty addressing methods, problem types and formulations, objective functions, optimization algorithms and additional features. Each part is detailed thoroughly to provide an instructive overview of the research output in the area. Subsequently, several aspects of interest are discussed in depth: the future of dealing with uncertainty, the main contributions and trends, and the relative importance of the field. It is expected that this review will be of use to both experts and lay people to learn more about the current state of optimization models in DGSs and provide insights into how to further develop this field. Full article
Show Figures

Figure 1

14 pages, 1843 KiB  
Article
Conversion of Waste Corn Straw to Value-Added Fuel via Hydrothermal Carbonization after Acid Washing
by Shulun Han, Li Bai, Mingshu Chi, Xiuling Xu, Zhao Chen and Kecheng Yu
Energies 2022, 15(5), 1828; https://doi.org/10.3390/en15051828 - 2 Mar 2022
Cited by 10 | Viewed by 2698
Abstract
To enhance the hydrothermal carbonization (HTC) process on biomass waste and improve the quality of biomass solid fuel. Corn straw was pretreated with acid washing and subsequently hydrothermally carbonized at 180–270 °C. The solid product obtained (hydrochars) was compared with the solid product [...] Read more.
To enhance the hydrothermal carbonization (HTC) process on biomass waste and improve the quality of biomass solid fuel. Corn straw was pretreated with acid washing and subsequently hydrothermally carbonized at 180–270 °C. The solid product obtained (hydrochars) was compared with the solid product produced from untreated hydrothermally carbonized straw. The results show that the acid pretreatment removed 7.9% of the ash from the straw. ICP and XRD analysis show that most of the alkali and alkaline earth metals have been removed. This addresses the defect of high ash content as the HTC temperature increases. The HHV of hydrochars produced by HTC after acid washing can reach 27.7 MJ/kg, which is nearly 10% higher than that of hydrochars prepared without acid washing pretreatment, and nearly 70% higher than that of straw raw materials. Elemental analysis and FTIR analysis show that the acid washing pretreatment changed the content and structure of the biomass components in the straw, resulting in a more complete HTC reaction and higher carbon sequestration. The decrease of H/C and O/C deepened the degree of coal-like transformation of hydrochars, with the lowest approaching the bituminous coal zone. The combustion characteristics of the hydrochars prepared after acid washing were significantly upgraded, the comprehensive combustion index and thermal stability of hydrochars both increased. Therefore, HTC after acid washing pretreatment is beneficial to further improve the high heating value and combustion characteristics of hydrochar. Full article
Show Figures

Figure 1

2021

Jump to: 2024, 2023, 2022, 2020

13 pages, 3029 KiB  
Article
The Effects of Module Temperature on the Energy Yield of Bifacial Photovoltaics: Data and Model
by Marco Leonardi, Roberto Corso, Rachela G. Milazzo, Carmelo Connelli, Marina Foti, Cosimo Gerardi, Fabrizio Bizzarri, Stefania M. S. Privitera and Salvatore A. Lombardo
Energies 2022, 15(1), 22; https://doi.org/10.3390/en15010022 - 21 Dec 2021
Cited by 22 | Viewed by 3859
Abstract
Bifacial photovoltaics (BPVs) are emerging with large momentum as promising solutions to improve energy yield and cost of PV systems. To reach its full potential, an accurate understanding of the physical characteristics of BPV technology is required. For this reason, we collected experimental [...] Read more.
Bifacial photovoltaics (BPVs) are emerging with large momentum as promising solutions to improve energy yield and cost of PV systems. To reach its full potential, an accurate understanding of the physical characteristics of BPV technology is required. For this reason, we collected experimental data to refine a physical model of BPV. In particular, we simultaneously measured the module temperature, short circuit current (Isc), open-circuit voltage (Voc), power at the maximum power point (Pmpp), and the energy yield of a bifacial and a monofacial minimodule. Such minimodules, realised with the same geometry, cell technology, and module lamination, were tested under the same clear sky outdoor conditions, from morning to afternoon, for three days. The bifacial system experimentally shows higher module temperatures under operation, about 10 °C on a daily average of about 40 °C. Nevertheless, its energy yield is about 15% larger than the monofacial one. We propose a physical quantitative model that fits the experimental data of module temperature, Isc, Voc, Pmpp, and energy yield. The model was then applied to predict the annual energy yield of PV module strings. The effect of different PV module temperature coefficients on the energy yield is also discussed. Full article
Show Figures

Figure 1

15 pages, 5789 KiB  
Article
Low Temperature One-Pot Hydrothermal Carbonization of Corn Straw into Hydrochar for Adsorbing Cadmium (II) in Wastewater
by Heng Li, Yan Shi, Li Bai, Mingshu Chi, Xiuling Xu and Yue Liu
Energies 2021, 14(24), 8503; https://doi.org/10.3390/en14248503 - 16 Dec 2021
Cited by 11 | Viewed by 2841
Abstract
Corn straw, a typical agricultural waste, was directly converted into hydrochar with a yield of 77.56% by hydrothermal carbonization at 140–230 °C for 2 h with a solid–liquid ratio of 1:20. The morphology and surface properties were characterized by elemental analysis, specific surface [...] Read more.
Corn straw, a typical agricultural waste, was directly converted into hydrochar with a yield of 77.56% by hydrothermal carbonization at 140–230 °C for 2 h with a solid–liquid ratio of 1:20. The morphology and surface properties were characterized by elemental analysis, specific surface area and pore size analysis and Fourier transform infrared spectroscopy. The results showed that with the increase of hydrothermal reaction temperature, some physical and chemical properties such as the increase of hydrocarbon content, crystallinity, and specific surface area of hydrochar changed significantly. A series of chemical reactions such as dehydration, decarboxylation, and aromatization occurred in the hydrothermal carbonization process so that the prepared hydrochar had rich oxygen-containing functional groups (-HO, C-O-C, C=O) and unique porous structure made the hydrochar prepared at 170 °C had the best removal effect on Cd2+ in solution (5.84 mg/g). These specific conditions could remove Cd2+ and greatly improve the adsorption performance. The pseudo-second-order kinetic model and Freundlich isotherm model could better describe the adsorption behavior of Cd2+. Therefore, corn straw hydrochar as a potential adsorbent for removing Cd2+ from water. Full article
Show Figures

Figure 1

25 pages, 4073 KiB  
Review
Brief Review of Photocatalysis and Photoresponse Properties of ZnO–Graphene Nanocomposites
by Chenhao Gao, Keyi Zhong, Xuan Fang, Dan Fang, Hongbin Zhao, Dengkui Wang, Bobo Li, Yingjiao Zhai, Xueying Chu, Jinhua Li and Xiaohua Wang
Energies 2021, 14(19), 6403; https://doi.org/10.3390/en14196403 - 7 Oct 2021
Cited by 13 | Viewed by 2854
Abstract
As a typical wide bandgap semiconductor, ZnO has received a great deal of attention from researchers because of its strong physicochemical characteristics. During the past few years, great progress has been made in the optoelectronic applications of ZnO, particularly in the photocatalysis and [...] Read more.
As a typical wide bandgap semiconductor, ZnO has received a great deal of attention from researchers because of its strong physicochemical characteristics. During the past few years, great progress has been made in the optoelectronic applications of ZnO, particularly in the photocatalysis and photodetection fields. To enable further improvements in the material’s optoelectronic performance, construction of a variety of ZnO-based composite structures will be essential. In this paper, we review recent progress in the growth of different ZnO–graphene nanocomposite structures. The related band structures and photocatalysis and photoresponse properties of these nanocomposites are discussed. Additionally, specific examples of the materials are included to provide an insight into the common general physical properties and carrier transport characteristics involved in these unique nanocomposite structures. Finally, further directions for the development of ZnO–graphene nanocomposite materials are forecasted. Full article
Show Figures

Figure 1

35 pages, 2046 KiB  
Review
Methane Cracking for Hydrogen Production: A Review of Catalytic and Molten Media Pyrolysis
by Malek Msheik, Sylvain Rodat and Stéphane Abanades
Energies 2021, 14(11), 3107; https://doi.org/10.3390/en14113107 - 26 May 2021
Cited by 136 | Viewed by 20014
Abstract
Currently, hydrogen is mainly generated by steam methane reforming, with significant CO2 emissions, thus exacerbating the greenhouse effect. This environmental concern promotes methane cracking, which represents one of the most promising alternatives for hydrogen production with theoretical zero CO/CO2 emissions. Methane [...] Read more.
Currently, hydrogen is mainly generated by steam methane reforming, with significant CO2 emissions, thus exacerbating the greenhouse effect. This environmental concern promotes methane cracking, which represents one of the most promising alternatives for hydrogen production with theoretical zero CO/CO2 emissions. Methane cracking has been intensively investigated using metallic and carbonaceous catalysts. Recently, research has focused on methane pyrolysis in molten metals/salts to prevent both reactor coking and rapid catalyst deactivation frequently encountered in conventional pyrolysis. Another expected advantage is the heat transfer improvement due to the high heat capacity of molten media. Apart from the reaction itself that produces hydrogen and solid carbon, the energy source used in this endothermic process can also contribute to reducing environmental impacts. While most researchers used nonrenewable sources based on fossil fuel combustion or electrical heating, concentrated solar energy has not been thoroughly investigated, to date, for pyrolysis in molten media. However, it could be a promising innovative pathway to further improve hydrogen production sustainability from methane cracking. After recalling the basics of conventional catalytic methane cracking and the developed solar cracking reactors, this review delves into the most significant results of the state-of-the-art methane pyrolysis in melts (molten metals and salts) to show the advantages and the perspectives of this new path, as well as the carbon products’ characteristics and the main factors governing methane conversion. Full article
Show Figures

Figure 1

21 pages, 3814 KiB  
Article
A Procedure to Calculate First-Order Wave-Structure Interaction Loads in Wave Farms and Other Multi-Body Structures Subjected to Inhomogeneous Waves
by José Miguel Rodrigues
Energies 2021, 14(6), 1761; https://doi.org/10.3390/en14061761 - 22 Mar 2021
Cited by 5 | Viewed by 2675
Abstract
A typical assumption when performing analytical, numerical, and experimental studies in wave–structure interaction in multi-body problems such as for wave farms and very large floating structures is the homogeneity of the wave field. Important interactions between the floating elements are dependent on the [...] Read more.
A typical assumption when performing analytical, numerical, and experimental studies in wave–structure interaction in multi-body problems such as for wave farms and very large floating structures is the homogeneity of the wave field. Important interactions between the floating elements are dependent on the direction, amplitude, and phase of the waves acting on each. Then, wave homogeneity is probably unrealistic in near-shore areas where these installations are to be deployed. In the present work, an existing interaction method, which allows the use of standard boundary element diffraction codes for solving the first order wave structure linear potential for each unique geometry in the problem, is shown to be able to account for inhomogeneous sea states across the domain of a multi-body problem requiring only minimal modification to its implementation. A procedure to use the method to include arbitrary incoming undisturbed wave conditions at each body is presented. A verification study was done by using an artificial numerical configuration to mimic an inhomogeneous wave field in a standard diffraction code, which was used as a reference. The results obtained using the interaction-method based procedure are shown to be in excellent agreement with the reference ones. Furthermore, an example of frequency inhomogeneity of the wave field in a wave farm is shown and the effects on the motion amplitudes and absorbed power are presented illustrating the applicability of the procedure. Full article
Show Figures

Figure 1

23 pages, 32320 KiB  
Article
Control of the Hybrid Renewable Energy System with Wind Turbine, Photovoltaic Panels and Battery Energy Storage
by Piotr Gajewski and Krzysztof Pieńkowski
Energies 2021, 14(6), 1595; https://doi.org/10.3390/en14061595 - 13 Mar 2021
Cited by 42 | Viewed by 9058
Abstract
The aim of the paper is the study of the Hybrid Renewable Energy System, which is consisted of two types of renewable energy systems (wind and sun) and is combined with storage energy system (battery). The paper presents the classification and review of [...] Read more.
The aim of the paper is the study of the Hybrid Renewable Energy System, which is consisted of two types of renewable energy systems (wind and sun) and is combined with storage energy system (battery). The paper presents the classification and review of architectures of Hybrid Renewable Energy Systems. The considered Hybrid Renewable Energy System was designed as a multi-converter system with gearless Wind Turbine driven Permanent Magnet Synchronous Generator and with a Photovoltaic Array and Battery Energy System. The mathematical models of individual elements of a complex Hybrid Renewable Energy System were described. In the control of both systems of Wind Turbine with Permanent Magnet Synchronous Generator and Photovoltaic array, the algorithms of Maximum Power Point Tracking have been implemented for higher efficiency of energy conversion. The energy storage in the battery has been managed by the control system of a bidirectional DC/DC converter. For the control of the Machine Side Converter and Wind Turbine with Permanent Magnet Synchronous Generator, the vector control method has been implemented. In the control system of the Grid Side Converter, the advanced method of Direct Power Control has been applied. The energy management strategies for optimal flows of electrical energy between individual systems of considered hybrid renewable energy system are developed and described. In order to determine the operation of proposed control systems, the simulation studies have been performed for different conditions of operation of individual elements of the complex hybrid system. The considered control methods and energy management strategies were tested thorough simulation studies for different wind speed variations, different sun irradiations, and different local load demands. The performed simulations are of practical importance in terms of proper operation requirements, design selection of components and energy management of Hybrid Renewable Energy Systems. Full article
Show Figures

Figure 1

24 pages, 2551 KiB  
Article
A Study on the Characteristics of Academic Topics Related to Renewable Energy Using the Structural Topic Modeling and the Weak Signal Concept
by Chankook Park and Minkyu Kim
Energies 2021, 14(5), 1497; https://doi.org/10.3390/en14051497 - 9 Mar 2021
Cited by 5 | Viewed by 3039
Abstract
It is important to examine in detail how the distribution of academic research topics related to renewable energy is structured and which topics are likely to receive new attention in the future in order for scientists to contribute to the development of renewable [...] Read more.
It is important to examine in detail how the distribution of academic research topics related to renewable energy is structured and which topics are likely to receive new attention in the future in order for scientists to contribute to the development of renewable energy. This study uses an advanced probabilistic topic modeling to statistically examine the temporal changes of renewable energy topics by using academic abstracts from 2010–2019 and explores the properties of the topics from the perspective of future signs such as weak signals. As a result, in strong signals, methods for optimally integrating renewable energy into the power grid are paid great attention. In weak signals, interest in large-capacity energy storage systems such as hydrogen, supercapacitors, and compressed air energy storage showed a high rate of increase. In not-strong-but-well-known signals, comprehensive topics have been included, such as renewable energy potential, barriers, and policies. The approach of this study is applicable not only to renewable energy but also to other subjects. Full article
Show Figures

Figure 1

26 pages, 7647 KiB  
Article
Investigation into Sizing Photovoltaic with Energy Storage for Off-Grid Transactive Scenarios
by David Vance, Ali Razban, Peter Schubert and Robert Weissbach
Energies 2021, 14(4), 1062; https://doi.org/10.3390/en14041062 - 18 Feb 2021
Cited by 5 | Viewed by 2140
Abstract
In this study, a novel sizing methodology was developed for centralized and interconnected operating strategies of transactive microgrids and several variables were investigated including starting month, initial charge of battery, load variability, unit cost of solar panels and energy storage, number of systems, [...] Read more.
In this study, a novel sizing methodology was developed for centralized and interconnected operating strategies of transactive microgrids and several variables were investigated including starting month, initial charge of battery, load variability, unit cost of solar panels and energy storage, number of systems, climate, and required reliability to determine their effect on total cost. The centralized strategy improved cost by seven to ten percent compared to the isolated strategy in every case. The interconnected strategy saved an incremental amount of money consistently compared to the isolated standard. The number of connected systems was not a strong effect. It was thought that increasing the number of systems would increase the benefit of energy sharing. Climate zones studied (“Cold”; “Hot-Dry/Mixed Dry”; “Mixed Humid”; and “Cold but with lower solar irradiation”) showed a large variation on cost with the Hot-Dry/Mixed Dry being the least expensive and Cold, with lower solar irradiation being the most expensive. Cost sensitivity analysis was performed showing that the unit cost of solar has a greater effect on the total cost. Required reliability of power, measured in outage hours, exhibited an inverse relation with cost. Full article
Show Figures

Figure 1

21 pages, 4047 KiB  
Article
Home Energy Management for Community Microgrids Using Optimal Power Sharing Algorithm
by Md Mamun Ur Rashid, Majed A. Alotaibi, Abdul Hasib Chowdhury, Muaz Rahman, Md. Shafiul Alam, Md. Alamgir Hossain and Mohammad A. Abido
Energies 2021, 14(4), 1060; https://doi.org/10.3390/en14041060 - 18 Feb 2021
Cited by 25 | Viewed by 3776
Abstract
From a residential point of view, home energy management (HEM) is an essential requirement in order to diminish peak demand and utility tariffs. The integration of renewable energy sources (RESs) together with battery energy storage systems (BESSs) and central battery storage system (CBSS) [...] Read more.
From a residential point of view, home energy management (HEM) is an essential requirement in order to diminish peak demand and utility tariffs. The integration of renewable energy sources (RESs) together with battery energy storage systems (BESSs) and central battery storage system (CBSS) may promote energy and cost minimization. However, proper home appliance scheduling along with energy storage options is essential to significantly decrease the energy consumption profile and overall expenditure in real-time operation. This paper proposes a cost-effective HEM scheme in the microgrid framework to promote curtailing of energy usage and relevant utility tariff considering both energy storage and renewable sources integration. Usually, the household appliances have different runtime preferences and duration of operation based on user demand. This work considers a simulator designed in the C++ platform to address the domestic customer’s HEM issue based on usages priorities. The positive aspects of merging RESs, BESSs, and CBSSs with the proposed optimal power sharing algorithm (OPSA) are evaluated by considering three distinct case scenarios. Comprehensive analysis of each scenario considering the real-time scheduling of home appliances is conducted to substantiate the efficacy of the outlined energy and cost mitigation schemes. The results obtained demonstrate the effectiveness of the proposed algorithm to enable energy and cost savings up to 37.5% and 45% in comparison to the prevailing methodology. Full article
Show Figures

Figure 1

21 pages, 8573 KiB  
Article
Voltage Optimization in MV Network with Distributed Generation Using Power Consumption Control in Electrolysis Installations
by Paweł Pijarski and Piotr Kacejko
Energies 2021, 14(4), 993; https://doi.org/10.3390/en14040993 - 14 Feb 2021
Cited by 13 | Viewed by 2895
Abstract
Connecting a large number of distributed sources to the medium and low voltage grid poses many problems. The most important of these are the voltage changes inside the network, what can be observed when the power flow from these sources towards the HV/MV [...] Read more.
Connecting a large number of distributed sources to the medium and low voltage grid poses many problems. The most important of these are the voltage changes inside the network, what can be observed when the power flow from these sources towards the HV/MV (High Voltage/Medium Voltage) transformer station. In particular, if the power consumption in nodes of the MV network is small and the distance between the place of installation of the source and the substation is large, increases and changes in voltage may be dangerous for the insulation of the network and burdensome for the consumers connected to it. The solution most frequently used to control voltage increases is the appropriate setting of the controller that affects the on-load tap changer of the MV/HV or even MV/LV (Medium Voltage/Low Voltage) transformer. It is also possible to regulate the reactive power of the sources and, of course, to limit their generated active power (curtailment of generation). The development of energy storage technology has made it possible to introduce consumers into the network, whose power can be controlled in a wide range. The article proposes the concept of an innovative voltage control system in the MV network, whose output values are three groups of parameters: HV/MV transformer ratio, reactive power of sources and active power of consumers connected in generation nodes. In the technological sense, it has been assumed that the loads are installations of electrolyzers used to produce “green hydrogen”, according to the P2G (Power to Gas) formula. The tests consisting in the execution of several hundred calculation cycles for the IEEE 37 test network, using the Monte Carlo simulation, have shown that the subordination of the hydrogen production process to the objectives of voltage control in the MV network clearly contributes to stabilizing its value, while meeting the technological requirements. The control variables of the proposed control system are the result of the optimization algorithm described in the article, the function of which is the quality of network voltage. Full article
Show Figures

Figure 1

21 pages, 4040 KiB  
Article
Prospects and Obstacles for Green Hydrogen Production in Russia
by Alexandra Kopteva, Leonid Kalimullin, Pavel Tcvetkov and Amilcar Soares
Energies 2021, 14(3), 718; https://doi.org/10.3390/en14030718 - 30 Jan 2021
Cited by 44 | Viewed by 6575
Abstract
Renewable energy is considered the one of the most promising solutions to meet sustainable development goals in terms of climate change mitigation. Today, we face the problem of further scaling up renewable energy infrastructure, which requires the creation of reliable energy storages, environmentally [...] Read more.
Renewable energy is considered the one of the most promising solutions to meet sustainable development goals in terms of climate change mitigation. Today, we face the problem of further scaling up renewable energy infrastructure, which requires the creation of reliable energy storages, environmentally friendly carriers, like hydrogen, and competitive international markets. These issues provoke the involvement of resource-based countries in the energy transition, which is questionable in terms of economic efficiency, compared to conventional hydrocarbon resources. To shed a light on the possible efficiency of green hydrogen production in such countries, this study is aimed at: (1) comparing key Russian trends of green hydrogen development with global trends, (2) presenting strategic scenarios for the Russian energy sector development, (3) presenting a case study of Russian hydrogen energy project «Dyakov Ust-Srednekanskaya HPP» in Magadan region. We argue that without significant changes in strategic planning and without focus on sustainable solutions support, the further development of Russian power industry will be halted in a conservative scenario with the limited presence of innovative solutions in renewable energy industries. Our case study showed that despite the closeness to Japan hydrogen market, economic efficiency is on the edge of zero, with payback period around 17 years. The decrease in project capacity below 543.6 MW will immediately lead to a negative NPV. The key reason for that is the low average market price of hydrogen ($14/kg), which is only a bit higher than its production cost ($12.5/kg), while transportation requires about $0.96/kg more. Despite the discouraging results, it should be taken into account that such strategic projects are at the edge of energy development. We see them as an opportunity to lead transnational energy trade of green hydrogen, which could be competitive in the medium term, especially with state support. Full article
Show Figures

Figure 1

2020

Jump to: 2024, 2023, 2022, 2021

16 pages, 5551 KiB  
Article
Experimental Determination of the Influence of Shape on the Heat Transfer Process in a Crushed Granite Storage Bed
by Magdalena Nemś
Energies 2020, 13(24), 6725; https://doi.org/10.3390/en13246725 - 20 Dec 2020
Cited by 3 | Viewed by 2343
Abstract
The article presents the problem of modelling the charging of a constant-phase bed storage in the first hours of the process. The places of errors in the heat transfer calculations for the packed beds were indicated. Granite in the shape of spheres and [...] Read more.
The article presents the problem of modelling the charging of a constant-phase bed storage in the first hours of the process. The places of errors in the heat transfer calculations for the packed beds were indicated. Granite in the shape of spheres and crushed rocks, with a characteristic dimension of 50 mm, was used for the experimental tests. The material was subjected to tomographic examination and then used as a storage material. The charging process was carried out for three flow rates: 0.006, 0.008 and 0.010 m3/s. After three hours of testing, the temperature of the outlet air for the granite sphere as the storage material was the same as for the granite crushed rock. However, the biggest differences occurred after 1 h of charging. They were equal to: 40.4% for the flow rate of 0.006 m3/s, 22.0% for the flow rate of 0.008 m3/s, and 18.5% for the flow rate of 0.010 m3/s. The differences were greater than the uncertainty of the measurements. As a result, different temperatures of the storage material were obtained. After three hours, they were equal to: 25.2%, 12.3% and 8.6% for the lowest, medium, and highest airflow, respectively. The conducted heat transfer analysis and the relationship Nu = f(Re) was determined. The influence of the calculated and actual surface of the crushed rock on the heat exchange process was explained. For all the tested air flow rates through the bed, higher thermal parameters were obtained for the crushed rock than for the sphere. The maximum differences in the Nu number were: 222.6%, 151.4% and 161.3% for the flow of 0.006, 0.008 and 0.010 m3/s, respectively. This means that the description of the heat exchange process in the piled beds would require a parameter that takes into account the geometry of the storage material. Full article
Show Figures

Figure 1

19 pages, 5111 KiB  
Article
Simulation of the Fast Pyrolysis of Coffee Ground in a Tilted-Slide Reactor
by Sang Kyu Choi, Yeon Seok Choi, Yeon Woo Jeong, So Young Han and Quynh Van Nguyen
Energies 2020, 13(24), 6605; https://doi.org/10.3390/en13246605 - 14 Dec 2020
Cited by 4 | Viewed by 2448
Abstract
The fast pyrolysis of coffee ground for bio-crude oil production was simulated in a tilted-slide reactor. The biochemical composition was derived by an extended biomass characterization method based on the elemental analysis. The simulation was performed in a steady-state and a Lagrangian multiphase [...] Read more.
The fast pyrolysis of coffee ground for bio-crude oil production was simulated in a tilted-slide reactor. The biochemical composition was derived by an extended biomass characterization method based on the elemental analysis. The simulation was performed in a steady-state and a Lagrangian multiphase model was adopted to describe the transport of sand and biomass particles together with a multistep kinetic mechanism for fast pyrolysis. When the secondary tar cracking reactions were not considered the volatile yield increased monotonically with temperature. The inclusion of secondary reactions could improve the prediction of volatile yield which turn to decrease at higher temperature. It was found that not only the maximum volatile yield but also the corresponding reactor temperature agreed well with the experimental results. At the temperature higher than 550 °C the trend of volatile yield is similar to that of experiment while it is larger at lower reactor temperature. The individual species yields were compared at various reactor temperatures and the pyrolysis processes were analyzed by tracking the reference components when they were decomposed along the distance. It was found that the reactor temperature should be above 500 °C for effective pyrolysis of all reference components of coffee ground. Full article
Show Figures

Figure 1

30 pages, 6667 KiB  
Review
A Comprehensive Review on Classification, Energy Management Strategy, and Control Algorithm for Hybrid Electric Vehicles
by Qicheng Xue, Xin Zhang, Teng Teng, Jibao Zhang, Zhiyuan Feng and Qinyang Lv
Energies 2020, 13(20), 5355; https://doi.org/10.3390/en13205355 - 14 Oct 2020
Cited by 53 | Viewed by 6419
Abstract
The energy management strategy (EMS) and control algorithm of a hybrid electric vehicle (HEV) directly determine its energy efficiency, control effect, and system reliability. For a certain configuration of an HEV powertrain, the challenge is to develop an efficient EMS and an appropriate [...] Read more.
The energy management strategy (EMS) and control algorithm of a hybrid electric vehicle (HEV) directly determine its energy efficiency, control effect, and system reliability. For a certain configuration of an HEV powertrain, the challenge is to develop an efficient EMS and an appropriate control algorithm to satisfy a variety of development objectives while not reducing vehicle performance. In this research, a comprehensive, multi-level classification for HEVs is introduced in detail from the aspects of the degree of hybridization (DoH), the position of the motor, the components and configurations of the powertrain, and whether or not the HEV is charged by external power. The principle and research status of EMSs for each type of HEV are summarized and reviewed. Additionally, the EMSs and control algorithms of HEVs are compared and analyzed from the perspectives of characteristics, applications, real-time abilities, and historical development. Finally, some discussions about potential directions and challenges for future research on the energy management systems of HEVs are presented. This review is expected to bring contribution to the development of efficient, intelligent, and advanced EMSs for future HEV energy management systems. Full article
Show Figures

Figure 1

25 pages, 1901 KiB  
Article
Performance Evaluation of Analytical Methods for Parameters Extraction of Photovoltaic Generators
by Nader Anani and Haider Ibrahim
Energies 2020, 13(18), 4825; https://doi.org/10.3390/en13184825 - 15 Sep 2020
Cited by 5 | Viewed by 2476
Abstract
This paper presents a succinct exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the [...] Read more.
This paper presents a succinct exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the development of each method. To evaluate the performance of these methods, MATLAB-based software has been devised and deployed to generate the results of each method when used to extract the SDM parameters of various PV test modules of different PV technologies. Similar software has also been developed to extract the same parameters using well-established numerical and iterative techniques. A comparison is subsequently made between the synthesized results and those obtained using numerical and iterative methods. The comparison indicates that although analytical methods may involve a significant amount of approximations, their accuracy can be comparable to that of their numerical and iterative counterparts, with the added advantage of a significant reduction in computational complexity, and without the initialization and convergence difficulties, which are normally associated with numerical methods. Full article
Show Figures

Figure 1

22 pages, 1325 KiB  
Article
A Comparison of Dispatchable RES Technoeconomics: Is There a Niche for Concentrated Solar Power?
by Alexandra G. Papadopoulou, George Vasileiou and Alexandros Flamos
Energies 2020, 13(18), 4768; https://doi.org/10.3390/en13184768 - 12 Sep 2020
Cited by 8 | Viewed by 3736
Abstract
Raising the penetration of renewable energy sources constitutes one of the main pillars of contemporary decarbonization strategies. Within this context, further progress is required towards the optimal exploitation of their potential, especially in terms of dispatchability, where the role of storage is considered [...] Read more.
Raising the penetration of renewable energy sources constitutes one of the main pillars of contemporary decarbonization strategies. Within this context, further progress is required towards the optimal exploitation of their potential, especially in terms of dispatchability, where the role of storage is considered vital. Although current literature delves into either storage per se or the integration of storage solutions in single renewable technologies, the comparative advantages of each technology remain underexplored. However, high-penetration solutions of renewable energy sources (RES) are expected to combine different technological options. Therefore, the conditions under which each technology outperforms their counterparts need to be thoroughly investigated, especially in cases where storage components are included. This paper aims to deal with this gap, by means of assessing the combination of three competing technologies, namely concentrated solar power (CSP), photovoltaics (PV) and offshore wind, with the storage component. The techno-economic assessment is based on two metrics; the levelized cost of electricity and the net present value. Considering the competition between the technologies and the impact storage may have, the paper’s scope lies in investigating the circumstances, under which CSP could have an advantage against comparable technologies. Overall, PVs combined with storage prevail, as the most feasible technological option in the examined storage scenarios—with an LCOE lower than 0.11 €/kWh. CSP LCOE ranged between 0.1327–0.1513 €/kWh for high capacity factors and investment costs, thus larger storage components. Offshore wind—with a lower storage component—had an LCOE of 0.1402 €/kWh. Thus, CSP presents the potential to outperform offshore wind in cases where the latter technology is coupled with high storage requirements. CSP can be viewed as one of the options that could support European Union (EU) decarbonization scenarios. As such, an appropriate market design that takes into consideration and values CSP characteristics, namely dispatchability, is needed at the EU level. Full article
Show Figures

Figure 1

18 pages, 6547 KiB  
Article
A Variable Fractional Order Fuzzy Logic Control Based MPPT Technique for Improving Energy Conversion Efficiency of Thermoelectric Power Generator
by N. Kanagaraj, Hegazy Rezk and Mohamed R. Gomaa
Energies 2020, 13(17), 4531; https://doi.org/10.3390/en13174531 - 1 Sep 2020
Cited by 31 | Viewed by 2754
Abstract
Thermoelectric generation technology is considered to be one of the viable methods to convert waste heat energy directly into electricity. The utilization of this technology has been impeded due to low energy conversion efficiency. This paper aims to improve the energy conversion efficiency [...] Read more.
Thermoelectric generation technology is considered to be one of the viable methods to convert waste heat energy directly into electricity. The utilization of this technology has been impeded due to low energy conversion efficiency. This paper aims to improve the energy conversion efficiency of the thermoelectric generator (TEG) model with a novel maximum power point tracking (MPPT) technique. A variable fractional order fuzzy logic controller (VFOFLC)-based MPPT technique is proposed in the present work in which the operating point of the TEG is moved quickly towards an optimal position to increase the energy harvesting. The fraction order term α, introduced in the MPPT algorithm, will expand or contract the input domain of the fuzzy logic controller (FLC to shorten the tracking time and maintain a steady-state output around the maximum power point (MPP). The performance of the proposed MPPT technique was verified with the TEG model by simulation using MATLAB /SIMULINK software. Then, the overall performance of the VFOFLC-based MPPT technique was analyzed and compared with Perturb and observe (P&O) and incremental resistance (INR)-based MPPT techniques. The obtained results confirm that the proposed MPPT technique can improve the energy conversion efficiency of the TEG by harvesting the maximum power within a shorter time and maintaining a steady-state output when compared to other techniques. Full article
Show Figures

Figure 1

12 pages, 2451 KiB  
Article
Characteristics of Flame Stability and Gaseous Emission of Bio-Crude Oil from Coffee Ground in a Pilot-Scale Spray Burner
by Sang Kyu Choi, Yeon Seok Choi, Yeon Woo Jeong, So Young Han and Quynh Van Nguyen
Energies 2020, 13(11), 2882; https://doi.org/10.3390/en13112882 - 4 Jun 2020
Cited by 5 | Viewed by 2526
Abstract
Coffee ground has been recently considered as a new biomass resource in relation to the increasing coffee consumption worldwide. The bio-crude oil can be produced by fast pyrolysis of coffee ground, and it has advantages of larger heating values in comparison with those [...] Read more.
Coffee ground has been recently considered as a new biomass resource in relation to the increasing coffee consumption worldwide. The bio-crude oil can be produced by fast pyrolysis of coffee ground, and it has advantages of larger heating values in comparison with those from other biomass. But the bio-crude oil from coffee ground has a significantly high viscosity which can hinder the application to conventional burners. In this study, a pilot-scale burner system with a 35 kW capacity with an air-blast atomizing nozzle was developed for the combustion of bio-crude oil from coffee ground with a high viscosity. A downward fuel injection system was adopted to enhance the ignition of fuel spray and the flame stabilization, and a movable block swirl generator was installed for the combustion air. The bio-crude oil was blended with ethanol at the volumetric ratio of 9:1 to enhance the combustion characteristics. The effect of various atomizing air pressures, swirl intensities, and overall equivalence ratios on the flame stability and gaseous emission were investigated to find out the optimum operating conditions for a bio-crude oil burner. Full article
Show Figures

Graphical abstract

Back to TopTop