Search Results (61)

The integration of microstructured current collectors offers a potential pathway to enhance interface properties in solid-state battery architectures. In this work, we investigate the influence of surface morphology on the electrochemical performance of Zn/Na_2.99Ba_0.005OCl/Cu electrodeless pouch cells by fabricating copper thin films on microstructured parylene-C substrates using a combination of colloidal lithography and reactive ion etching. O₂ plasma etching times ranging from 0 to 15 min were used to tune the surface topography, resulting in a systematic increase in root-mean-square roughness and a surface area enhancement of up to ~30% for the longest etching duration, measured via AFM. Kelvin probe force microscopy-analyzed surface potential showed maximum differences of 270 mV between non-etched and 12-minute-etched Cu collectors. The results revealed that the chemical potential is the property that relates the surface of the Cu current collector/electrode with the cell’s ionic transport performance, including the bulk ionic conductivity, while four-point sheet resistance measurements confirmed that the copper layers’ resistivity maintained values close to those of bulk copper (1.96–4.5 µΩ.cm), which are in agreement with electronic mobilities (−6 and −18 cm²V⁻¹s⁻¹). Conversely, the charge carrier concentrations (−1.6 to −2.6 × 10²³ cm⁻³) are indirectly correlated with the performance of the cell, with the samples with lower CCC_bulk (fewer free electrons) performing better and showing higher maximum discharge currents, interfacial capacitance, and first-cycle discharge plateau voltage and capacity. The data were further consolidated with Scanning Electron Microscopy and X-ray Photoelectron Spectroscopy analyses. These results highlight that the correlation between the surface morphology and the cell is not straightforward, with the microstructured current collectors’ surface chemical potential and the charge carriers’ concentration being determinant in the performance of all-solid-state electrodeless sodium battery systems. Full article

As the crucial current collector for lithium-ion batteries (LIBs), electrolytic copper foils are generally manufactured by electrodeposition in acidic copper sulfate solution. However, there are many disadvantages for traditional electrolytic copper foils, such as coarse grains, insufficient mechanical properties, and high energy consumption. In order to improve the performances of electrolytic copper foil, a novel cuprous electrodeposition system was developed in this study. A soluble cuprous coordination compound was synthesized. In addition, XPS, FT-IR spectrum, as well as single-crystal X-ray diffraction illustrated that thiourea coordinated with Cu(I) through S atom and therefore stabilized Cu(I) by the formation of CuCl·3TU. Importantly, the corresponding electrochemical behaviors were investigated. In aqueous solution, two distinct reduction processes were demonstrated by linear sweep voltammetry (LSV) at rather negative potentials, including the reduction of adsorbed state and non-adsorbed state. Moreover, the observed inductive loops in electrochemical impedance spectroscopy further confirmed the adsorption phenomenon. More significantly, the designed cuprous electrodeposition system could contribute to low energy consumptions during electrolysis. and produce ultrathin nanocrystalline copper foils with appropriate roughness. Consequently, the electrolysis method based on CuCl·3TU could provide an improved approach for copper foils manufacturing in advanced LIBs fabrication. Full article

This study investigates the emission characteristics and environmental impacts of pollutants from bagasse-fired biomass boilers through the integrated field monitoring of two sugarcane processing plants in Guangxi, China. Comprehensive analyses of flue gas components, including PM_2.5, NOx, CO, heavy metals, VOCs, HCl, and HF, revealed distinct physicochemical and emission profiles. Bagasse exhibited lower C, H, and S content but higher moisture (47~53%) and O (24~30%) levels compared to coal, reducing the calorific values (8.93~11.89 MJ/kg). Particulate matter removal efficiency exceeded 98% (water film dust collector) and 95% (bag filter), while NOx removal varied (10~56%) due to water solubility differences. Heavy metals (Cu, Cr, Ni, Pb) in fuel migrated to fly ash and flue gas, with Hg and Mn showing notable volatility. VOC speciation identified oxygenated compounds (OVOCs, 87%) as dominant in small boilers, while aromatics (60%) and alkenes (34%) prevailed in larger systems. Ozone formation potential (OFP: 3.34~4.39 mg/m³) and secondary organic aerosol formation potential (SOAFP: 0.33~1.9 mg/m³) highlighted aromatic hydrocarbons (e.g., benzene, xylene) as critical contributors to secondary pollution. Despite compliance with current emission standards (e.g., PM < 20 mg/m³), elevated CO (>1000 mg/m³) in large boilers indicated incomplete combustion. This work underscores the necessity of tailored control strategies for OVOCs, aromatics, and heavy metals, advocating for stricter fuel quality and clear emission standards to align biomass energy utilization with environmental sustainability goals. Full article

Thin films of manganese–nickel–cobalt oxide with graphene (G@MNCO) were deposited on copper foam using electrochemical deposition. NiCo₂O₄ is the main phase in these films. As the proportion of graphene in the precursor solution increases, the oxygen vacancies in the samples also increase. The microstructure of these samples evolves into hierarchical vertical flake structures. Cyclic voltammetry measurements conducted within the potential range of 0–1.2 V reveal that the electrode with the highest graphene content achieves the highest specific capacitance, approximately 475 F/g. Furthermore, it exhibits excellent cycling durability, maintaining 95.0% of its initial capacitance after 10,000 cycles. The superior electrochemical performance of the graphene-enhanced, manganese-doped nickel–cobalt oxide electrode is attributed to the synergistic contributions of the hierarchical G@MNCO structure, the three-dimensional Cu foam current collector, and the binder-free fabrication process. These features promote quicker electrolyte ion diffusion into the electrode material and ensure robust adhesion of the active materials to the current collector. Full article

The global scarcity of freshwater, particularly in arid regions, has intensified interest in sustainable desalination technologies. Among these, solar still (SS) systems stand out for their low operational costs and environmental compatibility. This review presents a comprehensive analysis of recent advancements in solar still technologies, with a particular emphasis on innovative materials, thermal management strategies, and hybrid systems aimed at improving water productivity and cost-efficiency. Key technologies such as phase change materials (PCMs) and thermoelectric modules (TEMs) are examined in detail, showing up to 140% and 6.7-fold improvements in productivity, respectively, in select configurations. The review also synthesizes results from various studies using a comparative lens, highlighting combinations such as double-glazed glass with fins and TEMs (5.7-fold increase) and CuO–water nanofluids coupled with TEMs and vibration (5.3-fold increase). Cost analyses reveal that some configurations achieve water production at as low as 0.011 USD/L under real-world conditions in Rajshahi, Bangladesh, using an integrated system with an external condenser and solar collector. Unlike general reviews, this work systematically compares performance metrics, cost-effectiveness, and design innovations across multiple studies to provide a clearer perspective on technology viability. Future directions suggest the integration of hybrid approaches using PCM, TEM, nanotechnology, and advanced geometries to overcome current limitations and further advance solar desalination efficiency. Full article

In this work, hollow dodecahedral carbon structures with abundant N-doping sites and metal nanoparticles (NC-Co-CNTs) based on MOF-derivative materials were designed and prepared as host materials for lithium metal to ensure uniform lithium deposition on a Cu current collector. NC-Co-CNTs have good electrical conductivity, which ensures fast electron transport and Li⁺ transfer. The carbon nanotubes catalytically derived by Co can promote the uniform distribution of Li⁺ along the hollow dodecahedral carbon surface and deposition inside the cavity, and the larger electronegativity of N-doped sites and lithophilic sites such as Co nanoparticles can effectively adsorb lithium, inducing the Li⁺ to be deposited in the form of spherical lithium in a dendrite-free state, inhibiting the growth of dendritic lithium and improving the electrochemical performance of the lithium metal battery. Based on the above advantages, the electrodes of NC-Co-CNT-based symmetric cells present superior cycling performance for more than 1100 h with low overpotential at 1 mAh cm⁻²/1 mAh·cm⁻². Even cycling at high current density of 5 mA cm⁻² and high deposition parameters of 5 mAh cm⁻², it still cycles for up to 800 h at a relatively low overpotential. Full article

Li metal anodes could significantly improve battery energy density. However, Li generally electrodeposits in poorly controlled morphology, leading to safety and performance problems. One factor that controls Li anode performance and electrodeposition morphology is the nature of the electrolyte–current collector interface. Herein, we modify the Cu current collector interface by depositing precisely controlled nanoporous carbon (NPC) coatings using pulsed laser deposition to develop an understanding of how NPC coating density and thickness impact Li electrodeposition. We find that NPC density and thickness guide Li morphological evolution differently and dictate whether Li deposits at the NPC-Cu or NPC-electrolyte interface. NPC coatings generally lower overpotential for Li electrodeposition, though thicker NPC coatings limit kinetics when cycling at a high rate. Lower-density NPC enables the highest Coulombic efficiency (CE) during calendar aging tests, and higher-density NPC enables the highest CE during cycling tests. Full article

Solid-state batteries offer significant advantages but present several challenges. Given the complexity of these systems, it is good practice to begin the study with simpler models and progressively advance to more complex configurations, all while maintaining an understanding of the physical principles governing solid-state battery operation. The results presented in this work pertain to cells without traditional electrodes, thus providing a foundation for guiding the development of fully functional solid-state cells. The open circuit voltage (OCV) of the Cu/Na_2.99Ba_0.005ClO composite in a cellulose/Zn pouch cell achieves 1.10 V, reflecting the difference in the chemical potentials of the current collectors (CCs), Zn and Cu, serving as electrodes. After 120 days, while set to discharge, conversely to what was expected, a higher potential difference of 1.13 V was attained (capacity of 5.9 mAh·g⁻¹_electrolyte). By incorporating a layer of carbon felt, the OCV became 0.85 V; however, after 95 days, the potential difference increased to 1.20 V. Ab initio simulations were additionally performed on a Cu/Na₃ClO/Zn heterojunction showing the formation of dipoles and the Na deposition on Zn which is demonstrated experimentally. The sodium plating on the negative CC (Zn) takes place as the cell is set to discharge at room temperature but is not observed at 40 °C. Full article

Anode-free lithium batteries (AFLBs) present an opportunity to eliminate the need for conventional graphite electrodes or excess lithium–metal anodes, thus increasing the cell energy density and streamlining the manufacturing process. However, their attributed poor coulombic efficiency leads to rapid capacity decay, underscoring the importance of achieving stable plating and stripping of Li on the negative electrode for the success of this cell configuration. A promising approach is the utilization of lithiophilic coatings such as silver to mitigate the Li nucleation overpotential on the Cu current collector, thereby improving the process of Li plating/stripping. On the other hand, inkjet printing (IJP) emerges as a promising technique for electrode modification in the manufacturing process of lithium batteries, offering a fast and scalable technology capable of depositing both thin films and patterned structures. In this work, a Fujifilm Dimatix inkjet printer was used to deposit Ag sites on a Cu current collector, aiming to modulate the interfacial electrochemistry of the system. Samples were fabricated with varying areas of coverage and the electrochemical performance of the system was systematically evaluated from bare Cu (non-lithiophilic) to a designed pattern (partially lithiophilic) and the fully coated thin film case (lithiophilic). Increasing lithiophilicity resulted in lower charge transfer resistance, higher exchange current density and reduced Li nucleation overpotential (from 55.75 mV for bare Cu to 13.5 mV for the fully coated case). Enhanced half-cell cyclability and higher coulombic efficiency were also achieved (91.22% CE over 76 cycles for bare Cu, 97.01% CE over 250 cycles for the fully coated case), alongside more uniform lithium deposition and fewer macroscopic irregularities. Moreover, our observations demonstrated that surface patterning through inkjet printing could represent an innovative, easy and scalable strategy to provide preferential Li nucleation sites to guide the subsequent Li deposition. Full article

Copper sulfide ores frequently co-occur with pyrite, presenting a significant challenge for their selective separation during beneficiation processes. Despite advancements in flotation technology, there remains a critical need for efficient methods to enhance copper recovery while suppressing pyrite interference, particularly without compromising the associated precious metals such as gold and silver. Current practices often struggle with achieving high selectivity and recovery while maintaining environmental sustainability. Here, we investigate the efficacy of a ternary collector mixture consisting of ammonium dibutyl dithiophosphate (ADD), butyl xanthate (BX), and ethyl xanthate (EX) for the selective flotation of copper sulfide from a complex ore containing 0.79% Cu and associated precious metals (0.233 g/t Au and 5.83 g/t Ag). A combination of lime and hydrogen peroxide as inhibitors was employed to suppress pyrite effectively under alkaline conditions (pH = 11.33). The results demonstrate that the optimized ternary collector system (ADD:BX:EX at a ratio of 1:0.5:0.5) significantly improves the copper grade and recovery at an ultra-low dosage of 10 g/t. The optimized flotation method using the combined collectors and inhibitors effectively separated chalcopyrite from pyrite, achieving a copper concentrate with 20.08% Cu content and a recovery of 87.73%. Additionally, the process yielded notable recoveries of gold (9.22%) and silver (26.66%). These findings advance the field by providing a viable and environmentally conscious approach to the beneficiation of sulfide ores, potentially serving as a blueprint for processing similar mineral deposits while minimizing reagent usage and costs. Full article

Zinc-based batteries (ZBBs) have proven to be tremendously plausible for large-scale electrochemical energy storage applications due to their merits of desirable safety, low-cost, and low environmental impact. Nevertheless, the zinc metal anodes in ZBBs still suffer from many issues, including dendrite growth, hydrogen evolution reactions (HERs), corrosion, passivation, and other types of undesirable side reactions, which severely hinder practical application. The modification of Cu-based current collectors (CCs) has proven to be an efficient method to regulate zinc deposition and prevent dendritic growth, thereby improving the Coulombic efficiency (CE) and lifespan of batteries (e.g., up to 99.977% of CE over 6900 cycles after modification), which is an emerging research topic in recent years. In this review, we provide a systematic overview of the modification of copper-based CCs and their application in zinc metal anodes. The relationships between their modification strategies, nano-micro-structures, and electrochemical performance are systematically reviewed. Ultimately, their promising prospects for future development are also proposed. We hope that this review could contribute to the design of copper-based CCs for zinc-based batteries and facilitate their practical application. Full article

Compared to traditional lithium metal batteries, anode-free lithium metal batteries use bare current collectors as an anode instead of Li metal, making them highly promising for mass production and achieving high-energy density. The current collector, as the sole component of the anode, is crucial in lithium deposition-stripping behavior and greatly impacts the rate of Li depletion from the cathode. In this study, to investigate the lithiophilicity effect of the current collector on the solid electrolyte interface (SEI) film construction and cycling performance of anode-free lithium batteries, various lightweight paper-based current collectors were prepared by electroless plating Cu and lipophilic Ag on low-dust paper (LDP). The areal densities of the as-prepared LDP@Cu, LDP@Cu-Ag, and LDP@Ag were approximately 0.33 mg cm⁻². The use of lipophilic Ag-coated collectors with varying loadings allowed for the regulation of lipophilicity. The impacts of these collectors on the distribution of SEI components and Li depletion rate in common electrolytes were investigated. The findings suggest that higher loadings of lipophilic materials, such as Ag, on the current collector increase its lipophilicity but also lead to significant Li depletion during the cycling process in full-cell anode-free Li metal batteries. Thus, moderately lithiophilic current collectors, such as LDP@Cu-Ag, show more potential for Li deposition and striping and stable SEI with a low speed of Li depletion. Full article

Alkali metals (Li, Na, and K) are deemed as the ideal anode materials for next-generation high-energy-density batteries because of their high theoretical specific capacity and low redox potentials. However, alkali metal anodes (AMAs) still face some challenges hindering their further applications, including uncontrollable dendrite growth and unstable solid electrolyte interphase during cycling, resulting in low Coulombic efficiency and inferior cycling performance. In this regard, designing 3D current collectors as hosts for AMAs is one of the most effective ways to address the above-mentioned problems, because their sufficient space could accommodate AMAs’ volume expansion, and their high specific surface area could lower the local current density, leading to the uniform deposition of alkali metals. Herein, we review recent progress on the application of 3D Cu-based current collectors in stable and dendrite-free AMAs. The most widely used modification methods of 3D Cu-based current collectors are summarized. Furthermore, the relationships among methods of modification, structure and composition, and the electrochemical properties of AMAs using Cu-based current collectors, are systematically discussed. Finally, the challenges and prospects for future study and applications of Cu-based current collectors in high-performance alkali metal batteries are proposed. Full article

The study investigates the performance of fluid flow, thermal, and mass transport within a cavity, highlighting its application in various engineering sectors like nuclear reactors and solar collectors. Currently, the focus is on enhancing heat and mass transfer through the use of ternary hybrid nanofluid. Motivated by this, our research delves into the efficiency of double-diffusive natural convective (DDNC) flow, heat, and mass transfer of a ternary hybrid nanosuspension (a mixture of Cu-CuO-Al₂O₃ in water) in a quadrantal enclosure. The enclosure’s lower wall is set to high temperatures and concentrations (${\mathrm{T}}_{\mathrm{h}}$ and ${\mathrm{C}}_{\mathrm{h}}$), while the vertical wall is kept at lower levels (${\mathrm{T}}_{\mathrm{c}}$ and ${\mathrm{C}}_{\mathrm{c}}$). The curved wall is thermally insulated, with no temperature or concentration gradients. We utilize the finite element method, a distinguished numerical approach, to solve the dimensionless partial differential equations governing the system. Our analysis examines the effects of nanoparticle volume fraction, Rayleigh number, Hartmann number, and Lewis number on flow and thermal patterns, assessed through Nusselt and Sherwood numbers using streamlines, isotherms, isoconcentration, and other appropriate representations. The results show that ternary hybrid nanofluid outperforms both nanofluid and hybrid nanofluid, exhibiting a more substantial enhancement in heat transfer efficiency with increasing volume concentration of nanoparticles. Full article

The preparation of composite carbon nanomaterials is one of the methods for improving the electrochemical performance of carbon-based electrode materials for supercapacitors. However, traditional preparation methods are complicated and time-consuming, and the binder also leads to an increase in impedance and a decrease in specific capacitance. Therefore, in this work, we reduced Ni-Cu nanoparticles on the surface of nitrogen-doped carbon nanofibers (CNFs) by employing an electrostatic spinning method combined with pre-oxidation and annealing treatments. At the same time, Ni-Cu nanoparticles were vulcanized to Ni–Cu–S nanoparticles without destroying the structure of the CNFs. The area-specific capacitance of the CNFs/Ni–Cu–S–300 electrode reaches 1208 mF cm⁻² at a current density of 1 mA cm⁻², and the electrode has a good cycling stability with a capacitance retention rate of 76.5% after 5000 cycles. As a self-supporting electrode, this electrode can avoid the problem of the poor adhesion of electrode materials and the low utilization of active materials due to the inactivity of the binder and conductive agent in conventional collector electrodes, so it has excellent potential for application. Full article