Electrochem, Volume 5, Issue 3 (September 2024) – 7 articles

Cu₂(ZnSn)(S)₄ (copper, zinc, tin, and sulfide (CZTS)) provides possible advantages over CuInGaSe2 for thin-film photovoltaic devices because it has a higher band gap. Preparing CZTS by electrodeposition because of its high productivity and lower processing costs, electroplating is appealing. Recently published studies reported that the electrodeposition process of CZTS still faces significant obstacles, such as the sulfur atomic ratio (about half of the whole alloy), deposits’ adhesion, film quality, and optical properties. This work introduces an improved bath that facilitates the direct electroplating of CZTS from one processing step. The precursors used were significantly more diluted than the typical baths mentioned in the last few years. An extensive analysis of the electrochemical behavior at various rotation speeds is presented at room temperature (~22 °C). The deposited alloy’s composition and adherence to the molybdenum back contact are examined with agitation. The annealing process was carried out in an environment containing sulfur, and the metal was not added at this stage. The ultimate sulfur composition was adjusted to 50.2%, about the desired atomic ratio. The compound’s final composition was investigated using the Energy-Dispersive X-ray Spectroscopy technique. Finally, X-ray diffraction analysis was applied to analyze CZTS crystallography and to measure thickness. Full article

Direct testing of pesticide contaminants in drinking water is a challenge. Portable and sensitive sensor platforms are desirable to test water contaminants directly at farm and consumer levels. In this study, we have demonstrated the feasibility of an electrochemical sensor for the direct detection of paraquat (PQ) in drinking water samples. An immunoassay-based sensing platform was fabricated using PQ-specific antibody immobilized on the surface of the electrochemically reduced graphene oxide (rGO) modified screen-printed carbon electrode (rGO-SPCE). Using non-faradaic electrochemical impedance spectroscopy (EIS) as a detection tool, the sensor platform demonstrated a dynamic response for PQ concentration in drinking water ranging from 0.05 ng/mL to 72.9 ng/mL (0.19 to 243.8 nM), with a coefficient of determination (r²) of 0.997 and a limit of detection of 0.05 ng/mL (0.19 nM). Percentage recovery within ±20% error was obtained, and the sensor cross-reactivity test showed a selective response against glyphosate antigen. With the flexibility to use single-frequency EIS and low sample volume, the developed sensor demonstrated testing in water samples directly without any sample pre-processing. This low-volume electroanalytical sensor platforms can be translated into portable testing tools for the detection of various water contaminants. Full article

Extracellular electron transfer (EET) by sulfate-reducing bacteria (SRB), such as Desulfovibrio ferrophilus IS5, enables bacterial interactions with minerals, which are vital for biogeochemical cycling and environmental chemistry. Here, we explore the direct EET mechanisms through outer-membrane cytochromes (OMCs) using IS5 as a model SRB. We employed nanostructured electrodes arrayed with 0, 50, 200, and 500 nm long nanowires (NWs) coated with indium–tin–doped oxide to examine the impact of electrode morphology on the direct EET efficacy. Compared to flat electrodes, NW electrodes significantly enhanced current production in IS5 with OMCs. However, this enhancement was diminished when OMC expression was reduced. Differential pulse voltammetry revealed that NW electrodes specifically augmented redox peaks associated with OMCs without affecting those related to redox mediators, suggesting that NWs foster direct EET through OMCs. Scanning electron microscopy observations following electrochemical analyses revealed a novel vertical cell attachment and aggregation on NW electrodes, contrasting with the horizontal monolayer cell attachment on flat electrodes. This study presents the first evidence of the critical role of electrode nanoscale topography in modulating SRB cell orientation and aggregation behavior. The findings underscore the significant influence of electrode morphology on the direct EET kinetics, highlighting the potential impact of mineral morphology on mineral reduction and biogeochemical processes. Full article

The escalating concern over environmental pollutants, particularly brominated flame retardants (BFRs), demands sophisticated detection methodologies for compounds like Tetrabromobisphenol A (TBBPA) and Hexabromocyclododecane (HBCD). Amidst these challenges, advancements in electrochemical detection have notably focused on the integration of inorganic modifiers within carbon electrodes. Inorganic nanoparticles, known for their catalytic and surface-enhancing properties, play a pivotal role in augmenting the sensitivity and selectivity of electrode-based detection systems. These modifiers, encompassing materials such as graphene, CeO₂ nanocubes, and metal-organic frameworks, among others, have revolutionized the capabilities of carbon-based electrodes in accurately identifying specific BFRs. Full article

Battery-type hybrid supercapacitors (HSCs) (otherwise known as supercapatteries) are novel electrochemical energy storage devices bridge the gap between rechargeable batteries and traditional SCs. Herein, we report the synthesis of layered two-dimensional (2D) nickel disulfide (NiS₂) nanosheets (NSNs) modified with poly(3,4-ethylenedioxythiophene:polystyrene sulfonate (PEDOT:PSS) and their successful implementation in battery-type SCs. Initially, a layered 2D NSN is synthesized via a microwave-assisted hydrothermal method and further used as a template to coat PEDOT:PSS in order to prepare NiS₂@PEDOT:PSS nanocomposite electrodes by a facile drop-casting method. This is the first-time report on the synthesis of a hierarchical NiS₂@PEDOT:PSS nanocomposite electrode for battery-type HSC applications. An asymmetric battery-type HSC fabricated with NSN@PEDOT:PSS nanocomposite as positrode and activated carbon as negatrode delivers a maximum energy density of 52.1 Wh/kg at a current density of 1.6 A/g with a corresponding power density of 2500 W/kg. Full article

Ni–W alloys have received considerable interest as a promising structural material for microelectromechanical systems (MEMS) due to their exceptional properties, including hardness, ductility, corrosion resistance, and thermal stability. However, the electrodeposition of Ni–W alloys in the MEMS fabrication process to achieve intact structures with a thickness of several tens of micrometers is challenging due to the occurrence of cracking caused by side reactions and internal stresses during the electrodeposition process. To address this issue, our focus was on pulsed reverse electrodeposition (PRE) as a potential solution. The utilization of the PRE technique allows for a high concentration of reactive species on the electrode surface, thereby mitigating side reactions such as hydrogen generation. In this study, we examined the effects of the PRE method on the morphological characteristics, average crystal grain size, Vickers hardness, and micro-mechanical properties of Ni–W alloys. Full article

This work describes the fabrication and characterization of a new high surface area nanocomposite electrode containing reduced graphene oxide (rGO) and titanium nitride (TiN) for electrochemical applications. This approach involves electrochemically depositing rGO on a high surface area TiN nanorod array electrode to form a new nanocomposite electrode. The TiN nanorod array was first formed by the glancing angle deposition technique in a DC (Direct Current) sputtering system. GO flakes of ~1.5 μm in diameter, as confirmed by Dynamic Light Scattering (DLS), were electrodeposited on the nanostructured TiN electrode via the application of a fixed potential for one hour. The surface morphology of the as-prepared rGO/TiN electrode was evaluated by scanning electron microscopy (SEM) and the presence of rGO on TiN was confirmed by Raman Microscopy. The CV shows an increase in the capacitive current at rGO/TiN as compared to TiN. The rGO decorated TiN electrode was then used for analyzing the electrocatalytic oxidation of ascorbic acid and dopamine, and the reduction of nitrate by CV and linear sweep voltammetry (LSV), respectively. CV or LSV show that the electrochemical kinetics of these three analytes are significantly faster on rGO/TiN than TiN itself. Overall, the rGO/TiN electrode showed better electrochemical behavior for biomolecules like ascorbic acid and dopamine as well as another target analyte, nitrate ions, compared to TiN by itself. Full article