Search Results (58)

This study focuses on the synthesis, properties, and comparative analysis of new flame-retardant compounds: coumarins and isophosphinolines. These compounds feature a diarylphosphine oxide (DAPO) substituent at the β-position relative to both the carbonyl and the phosphoryl groups. Various derivatives with halogens, phosphorus, and/or aromatics substituents were synthetized and their thermal stability and flammability were evaluated at the microscale by thermogravimetric analysis (TGA) and pyrolysis–combustion flow calorimetry (PCFC) in order to identify the most promising molecules for use as flame-retardant (FR) additives or comonomers. FTIR-coupled PCFC analysis was also carried out to study the combustion profiles of the molecules. Beyond the confirmation of some expected trends, such as the char promotion of phosphorus and flame inhibition of halogens, the study revealed some unexpected findings that warrant further investigation. These include the prominent role of the chlorine substitution position on the aromatic ring, as well as significant differences in FR performance between diastereoisomers. Full article

The commercialization of proton-conducting fuel cells (PCFCs) is hindered by the limited electroactivity and durability of cathodes at intermediate temperatures ranging from 400 to 700 °C, a challenge exacerbated by an insufficient understanding of high-entropy perovskite (HEP) materials for oxygen reduction reaction (ORR) optimization. This study introduces an yttrium-doped HEP to address these limitations. A comparative analysis of Ce_0.2−xY_xBa_0.2Sr_0.2La_0.2Ca_0.2CoO_3−δ (x = 0, 0.2; designated as CBSLCC and YBSLCC) revealed that yttrium doping enhanced the ORR activity, reduced the thermal expansion coefficient (19.9 × 10⁻⁶ K⁻¹, 30–900 °C), and improved the thermomechanical compatibility with the BaZr_0.1Ce_0.7Y_0.1Yb_0.1O_3−δ electrolytes. Electrochemical testing demonstrated a peak power density equal to 586 mW cm⁻² at 700 °C, with a polarization resistance equaling 0.3 Ω cm². Yttrium-induced lattice distortion promotes proton adsorption while suppressing detrimental Co spin-state transitions. These findings advance the development of durable, high-efficiency PCFC cathodes, offering immediate applications in clean energy systems, particularly for distributed power generation. Full article

A biobased flame retardant, trieugenylphosphate (TEP), was synthesized from eugenol and incorporated at concentrations of 10 and 30 wt.% into the epoxy matrix. Flammability and thermal stability were investigated using the UL-94 test, pyrolysis–combustion flow calorimetry (PCFC), and thermogravimetric analysis (TGA). Thermal and thermomechanical properties were examined by differential scanning calorimetry (DSC) and dynamical mechanical thermal analysis (DMTA). The modified resin with TEP content showed self-extinguishing properties and acceptable thermal and thermomechanical properties. Furthermore, the microcalorimetric method proved that the introduction of the TEP additive to the epoxy matrix reduced the values of p_cHRR (414.4 ± 5.5 W/g), THR (29.1 ± 0.6 kJ/g), and HRC (446 ± 7 J/g·K) for the sample tested compared to the unmodified resin. Full article

Phosphorus flame retardants react with cellulose hydroxyl groups via esterification, enhancing the effectiveness of char formation, which is beneficial in terms of the search for bio-sourced flame retardants. The current work assessed the flammability of a new polymer synthesized by Michael 1,4-addition (rP) and modified with developed intumescent flame retardant systems (FRs), in which lignocellulose components, such as sunflower husk (SH) and peanut shells (PS), replaced a part of the synthetic ones. The thermal and thermomechanical properties of the rP, with 20 wt.% each from six FRs, were determined by thermogravimetric analysis (TG), differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). Moreover, the flammability and evolved gas were studied with pyrolysis combustion flow calorimetry (PCFC) and thermogravimetric analysis connected with Fourier transform infrared spectroscopy tests (TGA/FT-IR). The effects were compared to those achieved for unmodified rP and a polymer with a commercially available intumescent flame retardant (IFR). The notable improvement, especially in terms of the heat release rate and heat release capacity, indicates that the system with melamine phosphate (MP) and peanut shells (PS) can be used to decrease the flammability of new polymers. An extensive analysis of the composition and geometry of the ground shells and husk particles preceded the research. Full article

Polymer concrete (PC) is recognized for its lightweight nature, wear resistance, and rapid curing, making it well-suited for the repair of deteriorated infrastructure. This research critically addresses the challenge of enhancing overlay adhesion to compromised substrates by uniquely evaluating the role of pristine versus functionalized multi-walled carbon nanotubes (MWCNTs) in improving polymer concrete (PC) bond strength, particularly on concrete deteriorated by sulfate attack. PC mixtures containing varying concentrations of MWCNTs (0%, 0.25%, and 0.5% by weight) were prepared and tested for their mechanical properties, including compressive strength, modulus of rupture, and pull-off strength. Pull-off tests were conducted to assess the bond between PC overlays and Portland cement concrete (PCC) substrates. To examine the effects of substrate deterioration, PCC specimens were cured under two conditions: standard and sulfate-exposed environments. The results showed that neat polymer concrete (PC-Neat) achieved a high average pull-off strength of 2.82 MPa under normal conditions. Incorporating 0.25% pristine MWCNTs (PC-P25) significantly reduced the bond strength to 0.039 MPa. In contrast, improved performance was observed with functionalized MWCNTs. The addition of 0.5% COOH-functionalized MWCNTs (PC-FC50) yielded a pull-off strength of 2.22 MPa under normal conditions and 1.65 MPa in sulfate environments. Notably, under sulfate exposure, functionalized MWCNTs enhanced the bond strength by up to 15% compared to PC-Neat, highlighting their potential in aggressive environments. This distinct improvement in bond strength presents a significant finding, demonstrating a novel pathway for developing more resilient repair materials for infrastructure exposed to aggressive chemical environments. Full article

The control of powder aging during Selective Laser Sintering (SLS) processing is one of the challenges to be overcome for the implementation of this technique in serial production. Aging phenomena, because of the elevated temperatures and long processing times, need to be considered when a fraction of the polymer powders present in the build chamber and not used to manufacture the parts are reused at various times. The aim of this study was to investigate the influence of successive reuse of blends of pure Polyamide 12 and its blends with two types of flame retardants (FR): ammonium polyphosphate (APP) and zinc borate (ZB). The composition of the blends was 70/30 (wt/wt) PA 12/FR. Four successive processing stages have been carried out by collecting the remaining powder blend each time. The powders were re-used using the same processing parameters after sieving. DSC measurements showed that the incorporation of FRs entailed a reduction in the processing window up to 4 °C; nevertheless, no further reduction was noted after aging. The TGA curves of aged blends of powders were also similar for pure PA 12 and PA 12 with FR. In addition, initial and reused powders presented a higher degree of crystallinity than the specimens processed from the powders. The heterogeneous character of the PA 12 after LS processing or reprocessing was shown through Pyrolysis Combustion Flow Calorimetry (PCFC) and cone calorimeter (CC) tests. FTIR analysis also showed that post-condensation reactions have occurred. The mode of action of the flame retardants was clearly seen on HRR curves at both tests. The first reuses of PA 12 powders entailed a significant reduction in time to ignition at the cone calorimeter (150 for the initial material to around 90 s for the reused material), indicating the formation of short polymer chains. Only in the case of zinc borate was it noticed that re-used powder was detrimental to the fire performance because of a strong increase in the value of pHRR (between 163 and 220 kW/m² for reused material instead of 125 kW/m² for the initial one). Full article

Yttrium-doped barium zirconate is a commonly used electrolyte material for Protonic Ceramic Fuel Cells (PCFC) due to its high protonic conductivity and high chemical stability. However, it is also known for its poor sinterability and poor grain boundary conductivity. In this work, in response to these issues, reactive magnetron sputtering was strategically chosen as the electrolyte deposition technique. This method allows the creation of a 4 µm tick electrolyte with a dense columnar microstructure. Notably, this technique is not widely utilized in PCFC fabrication. In this study, a complete cell is elaborated without exceeding a sintering temperature of 1350 °C. Tape casting is used for the anode, and spray coating is used for the cathode. The material of interest is yttrium-doped barium zirconate with the formula BaZr_0.8Y_0.2O_3−δ (BZY). The anode consists of a NiO-BZY cermet, while the cathode is composed of BZY and Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSFC) in a 50:50 weight ratio. The electrochemical impedance spectroscopy analysis reveals a global polarization resistance of 0.3 Ω cm², indicating highly efficient interfaces between electrolytes and electrodes. Full article

Water pollutants harm ecosystems and degrade water quality. At the same time, many pollutants carry potentially valuable chemical energy, measured by chemical oxygen demand (COD). This study highlights the potential for energy harvesting during remediation using photocatalytic fuel cells (PCFCs), stressing the importance of economically viable and sustainable materials. To achieve this, this research explores alternatives to platinum cathodes in photocathodes and aims to develop durable, cost-effective photoanode materials. Here, zinc oxide nanorods of high density are fabricated on carbon fiber surfaces using a low-temperature aqueous chemical growth method that is simple, cost-efficient, and readily scalable. Alternatives to the Pt cathodes frequently used in PCFC research are explored in comparison with screen-printed PEDOT:PSS cathodes. The fabricated ZnO/carbon anode (1.5 × 2 cm²) is used to remove the model pollutant used here and salicylic acid from water (30 mL, 70 μM) is placed under simulated sunlight (0.225 Sun). It was observed that salicylic acid was degraded by 23 ±0.46% at open voltage (OV) and 43.2 ± 0.86% at 1 V with Pt as the counter electrode, degradation was 18.5 ± 0.37% at open voltage (OV) and 44.1 ± 0.88% at 1 V, while PEDOT:PSS was used as the counter electrode over 120 min. This shows that the PEDOT:PSS exhibits an excellent performance with the full potential to provide low-environmental-impact electrodes for PCFCs. Full article

On-site hydrogen generation from ammonia decomposition is a promising technology to address the challenges of direct transportation and storage of hydrogen. The main problems with the existing support materials for ammonia decomposition catalysts are their high cost and time-consuming preparation process. In this work, ammonia decomposition catalysts consisting of in situ-formed nano-Ru particles supported on a naturally abundant mineral fiber, attapulgite (ATP), were proposed and studied. Also, 1 wt.% Ru was uniformly dispersed and anchored onto the surface of ATP fibers via the chemical method. We found that the calcination temperatures of the ATP support before the deposition of Ru resulted in little difference in catalytic performance, while the calcination temperatures of the 1Ru/ATP precursor were found to significantly influence the catalytic performance. The prepared 1 wt.% Ru/ATP catalyst (1Ru/ATP) without calcination achieved an ammonia conversion efficiency of 51% at 500 °C and nearly 100% at 600 °C, with the flow rate of NH₃ being 10 sccm (standard cubic centimeter per minute). A 150 h continuous test at 600 °C showed that the 1Ru/ATP catalyst exhibited good stability with a degradation rate of about 0.01% h⁻¹. The 1Ru/ATP catalyst was integrated with proton ceramic fuel cells (PCFCs). We reported that PCFCs at 650 °C offered 433 mW cm⁻² under H₂ fuel and 398 mW cm⁻² under cracked NH₃ fuel. The overall results suggest low-level Ru-loaded ATP could be an attractive, low-cost, and efficient ammonia decomposition catalyst for hydrogen production. Full article

Short flax fibers have been modified by radiation-induced grafting using methacrylate monomers containing phosphorus to give them a flame-retardant character. Two methodologies, namely pre-irradiation and simultaneous irradiation grafting, were examined. Certain parameters, notably the dose and the irradiation source (e-Beam and γ rays), were evaluated. The grafting efficiency, in terms of phosphorus content (mass percentage), was measured by X-ray fluorescence spectrometry (XRF). Using simultaneous irradiation, 2.39 wt% phosphorus could be obtained from 10 kGy, compared to 100 kGy in pre-irradiation. Furthermore, for similar phosphorus levels, the location of the grafted polymer chains was different for the two methodologies. The effect of phosphorus content on thermal properties and fire behavior was evaluated on a microscopic scale using a pyrolytic flow combustion calorimeter (PCFC) and on a laboratory scale using a cone calorimeter. It was then pointed out that flammability was linked to the phosphorus content and likely its location, which is associated with the radiation-induced grafting methodology, showing that the grafting conditions influence the final fire properties. Simultaneous irradiation, thus, proved to be more interesting in terms of efficiency and final properties. Full article

Polyurethane (PUR), as an engineering polymer, is widely used in many sectors of industries. However, the high fire risks associated with PUR, including the smoke density, a high heat release rate, and the toxicity of combustion products limit its applications in many fields. This paper presents the influence of silsesquioxane fillers, alone and in a synergistic system with halogen-free flame-retardant compounds, on reducing the fire hazard of polyurethane foams. The flammability of PUR composites was determined with the use of a pyrolysis combustion flow calorimeter (PCFC) and a cone calorimeter. The flammability results were supplemented with smoke emission values obtained with the use of a smoke density chamber (SDC) and toxicometric indexes. Toxicometric indexes were determined with the use of an innovative method consisting of a thermo-balance connected to a gas analyzer with the use of a heated transfer line. The obtained test results clearly indicate that the used silsesquioxane compounds, especially in combination with organic phosphorus compounds, reduced the fire risk, as expressed by parameters such as the maximum heat release rate (HRRmax), the total heat release rate (THR), and the maximum smoke density (SDmax). The flame-retardant non-halogen system also reduced the amounts of toxic gases emitted during the decomposition of PUR, especially NOx, HCN, NH₃, CO and CO₂. According to the literature review, complex studies on the fire hazard of a system of POSS–phosphorus compounds in the PUR matrix have not been published yet. This article presents the complex results of studies, indicating that the POSS–phosphorous compound system can be treated as an alternative to toxic halogen flame-retardant compounds in order to decrease the fire hazard of PUR foam. Full article

Research has been conducted on solid oxide fuel cells (SOFCs) for their fuel flexibility, modularity, high efficiency, and power density. However, the high working temperature leads to the deterioration of materials and increased operating costs. Considering the high protonic conductivity and low activation energy, the proton conducting SOFC, i.e., the protonic ceramic fuel cell (PCFC), working at a low temperature, has been wildly investigated. The PCFC is a promising state-of-the-art electrochemical energy conversion system for ecological energy; it is characterized by near zero carbon emissions and high efficiency, and it is environment-friendly. The PCFC can be applied for the direct conversion of various renewable fuels into electricity at intermediate temperatures (400–650 °C). The construction of the PCFC directly affect its properties; therefore, manufacturing technology is the crucial factor that determines the performance. As a thinner electrolyte layer will lead to a lower polarization resistance, a uniformly constructed and crack-free layer which can perfectly bond to electrodes with a large effective area is challenging to achieve. In this work, different fabrication methods are investigated, and their effect on the overall performance of PCFCs is evaluated. This article reviews the recent preparation methods of PCFCs, including common methods, 3D printing methods, and other advanced methods, with summarized respective features, and their testing and characterization results. Full article

Cermet films consisting of Ni, BaCe_0.4Zr_0.4Y_0.2O_3−δ (BCZY), and Gd_0.1Ce_0.9O_x (GDC), specifically, 60 wt%Ni–BCZY, 60 wt%Ni–BCZY–GDC, and 60 wt%Ni–GDC, were formed on BCZY electrolyte supports as anodes of proton ceramic fuel cells (PCFCs). The Ni grain size in these films after sintering at 1450 °C was around 2 μm. The GDC addition did not affect the Ni grain size in the case of the BCZY matrix. The anodic properties greatly depended on the oxide phase composition and worsened with increasing the GDC content. This probably occurred because of the addition of GDC, which has low proton conductivity and inhibited the proton conduction path of BCZY, reducing three-phase boundaries in the anode bulk. Since BCZY has a lower grain growth rate during sintering than BaCe_0.8Y_0.2O_3−δ, the Ni grain growth was likely suppressed by the surrounding Ni grains containing small BCZY grains. Full article

Ba_0.5Sr_0.5FeO_3−δ (BSF) nanofibers are prepared via electrospinning and sintering at a temperature of 800 °C for 2 h to produce a pure cubic perovskite phase, with the aim of finding a high-performance cathode material suitable for proton-conducting solid oxide fuel cells (PCFCs) operating at medium temperatures. The results of SEM analysis showed that the BSF nanofibers are alternately stacked, presenting fluffy and uniform high porosity, which is favorable to the cathode polarization reaction of PCFCs. To balance the excessive coefficient of thermal expansion of the BSF cathode, it is combined with a negative thermal expansion (NTE) material NdMnO_3−δ (NM). At 700 °C, the peak power density (PPD) of the BSF–NM cathode cell is 1170 mW cm⁻², and the open-circuit voltage (OCV) of the single cell is 1.04 V. The corresponding polarization impedance (R_p) of the BSF–NM is 0.037 Ω cm². This result is significantly better than the previously reported powder cathode BSF, indicating that the performance of PCFC can be further optimized by transforming the BSF cathode into a nanofiber state and compounding it with the NTE material NM. Full article

Understanding the impact of sintering temperature on the physical and chemical properties of Ni-BaCe_0.54Zr_0.36Y_0.1O_3-δ (Ni-BCZY) composite anode is worthy of being investigated as this anode is the potential for protonic ceramic fuel cell (PCFC) application. Initially, NiO–BCZY composite powder with 50 wt% of NiO and 50 wt% of BCZY is prepared by the sol–gel method using citric acid as the chelating agent. Thermogravimetric analysis indicates that the optimum calcination temperature of the synthesised powder is 1100 °C. XRD result shows that the calcined powder exists as a single cubic phase without any secondary phase with the lattice parameter (a) of 4.332 Å. FESEM analysis confirms that the powder is homogeneous and uniform, with an average particle size of 51 ± 16 nm. The specific surface area of the calcined powder measured by the Brunauer–Emmett–Teller (BET) technique is 6.25 m²/g. The thickness, porosity, electrical conductivity and electrochemical performance of the screen-printed anode are measured as a function of sintering temperature (1200–1400 °C). The thickness of the sintered anodes after the reduction process decreases from 28.95 μm to 26.18 μm and their porosity also decreases from 33.98% to 26.93% when the sintering temperature increases from 1200 °C to 1400 °C. The electrical conductivities of the anodes sintered at 1200 °C, 1300 °C and 1400 °C are 443 S/cm, 633 S/cm and 1124 S/cm at 800 °C, respectively. Electrochemical studies showed that the anode sintered at 1400 °C shows the lowest area specific resistance (ASR) of 1.165 Ω cm² under a humidified (3% H₂O) gas mixture of H₂ (10%) and N₂ (90%) at 800 °C. Further improvement of the anode’s performance can be achieved by considering the properties of the screen-printing ink used for its preparation. Full article